IBM System storage DS6000 Series Redbook page 219
Copy services with ibm system z
Hide thumbs
Also See for System storage DS6000 Series:
- Redbooks (406 pages) ,
- Attachment manual (298 pages) ,
- Introduction and planning manual (119 pages)
Table of Contents
Advertisement
Establish a volume pair
Similar to System z volumes, we first have to collect the required information. In this example,
we already had a path defined to the secondary subsystem. We issued a CQUERY command
with the ODEVN parameter to check the status of the volume, as seen in Example 16-8. Note
that we have to direct the command (using the DEVN parameter) to a z/OS device with the
same server affinity as the open systems volume (therefore, in this example, we direct it to a
volume in LSS 00, which has the same server affinity as LSS 16).
Example 16-8 CQUERY for open systems device
CQUERY DEVN(6030) ODEVN(AAGXA X'00' X'16') VOLUME
The serial number of the DS subsystem is supplied, along with the LUN number (x'00') and
the LSS number (x'16'). The output appears similar to that shown in Example 16-9.
Example 16-9 CQUERY for open systems device output
ANTP8802I CQUERY DEVN(6030) ODEVN(AAGXA X'00' X'16') VOLUME
ANTP0090I CQUERY FORMATTED LVL 3 472
VOLUME REPORT
************** PPRC REMOTE COPY CQUERY - VOLUME ********************
*
*
*DEVICE
LEVEL
STATE
*------ --------- ---------- ----------- ---------
* 6030 ......... SIMPLEX...
*
...............
* PATHS SAID DEST STATUS: DESCRIPTION
* ----- --------- ------ -------------------
*
0
---- ----
00
*
---- ----
00
*
---- ----
00
*
---- ----
00
* SUBSYSTEM
WWNN
* ----------- ----------------
* PRIMARY.... 500507630EFFFC6F
* SECONDARY.1 500507630EFFFCA0
* SECONDARY.2 500507630EFFFCA0
********************************************************************
ANTP0001I CQUERY COMMAND COMPLETED FOR DEVICE 6030. COMPLETION CODE: 00
The device is in simplex state. Note the SSID reports with special value FF16; this is the open
systems LSS number preceded with FF.
We want to establish a pair with the secondary device on LSS 16, LUN number 00. The
command format that we use is shown in Example 16-10.
Example 16-10 CESTPAIR command for open systems LUN
CESTPAIR DEVN(X'6030') PRIM(X'FF16' AAGXA X'00' X'16') -
SEC(X'FF16' AAVCA X'00' X'16') OPENDVCS(YES) -
OPTION(SYNC) MODE(COPY)
We used the OPENDVCS parameter and the special SSID value FF16 to identify that this is
an open systems device, on LSS 16, and that we want to direct the command to the open
systems LSS. The LUN number is supplied where we would normally supply the CCA, and
the LSS number is supplied in the normal position. The output from this command and a
subsequent CQUERY are shown in Example 16-11 on page 196.
(PRIMARY)
SSID LUN LSS SSID LUN LSS*
PATH STATUS SERIAL#
INACTIVE
FF16 00 16
........... 0000000AAGXA ............*
NO PATH............
NO PATH............
NO PATH............
NO PATH............
LIC LEVEL
-----------
5.0.00.0000
(SECONDARY) *
SERIAL#
*
--------- *
.......... *
*
*
*
*
*
*
*
*
*
*
*
Chapter 16. Metro Mirror examples
195
Advertisement
Table of Contents
