Related Manuals for Ultratec LSG PFI-9D
Summary of Contents for Ultratec LSG PFI-9D
- Page 1 LSG Low Smoke Generator w/ Power Fog Industrial 9D Operator’s Manual www.ultratecfx.com VER. 04.11.12...
-
Page 2: Table Of Contents
Power Fogger Industrial 9D ............4 LSG w/ PFI-9D Technical Drawings ..........5 LSG PFI System on a Cart ............5 LSG PFI-9D System in a Roadcase ..........5 Operating Procedure ..............6 Operating Procedure w/ Air Option ........... 6 Operation Procedure LSG MK II High Pressure w/ 20 &... -
Page 3: Introduction
3. Allow sufficient air circulation around the machine at all times. 4. Protect the machine from direct weather effects and wet locations. 5. Only use fluids manufactured by Ultratec Special Effects. 6. Do not continue to produce fog when visibility is reduced to 20” 50cm or below. -
Page 4: Lsg Pfi-9D Technical Specifications
120 Volt - High Pressure PFI-9D System w/Cart Power Rating: 120 Volt A.C. 50/60 Hz. 13 Amps. 220-240 Volt A.C. 50/60 Hz. 6.5 Amps. Fluid: Water Base Fog Fluid (Use only Ultratec Fluid) PFI Technical Drawings Power Fogger Industrial 9D www.ultratecfx.com... -
Page 5: Lsg W/ Pfi-9D Technical Drawings
LSG w/ PFI-9D Technical Drawings LSG PFI System on a Cart 28.02 32.2 29.6 LSG PFI-9D System in a Roadcase 23.25 39.5 28.75 34.5 www.ultratecfx.com... -
Page 6: Operating Procedure
1. The fog machine must be connected to a grounded supply of at least 15 amps free of any electrical interference. 2. Open a 4L or 20 Litre (5 Gallon) container of Ultratec Special Effects fog fluid and insert the fluid pickup tube into the spout of the fluid container. -
Page 7: Operation Procedure Lsg Mk Ii High Pressure W/ 20 & 50Lbs Cylinders
2. Connect the grey Twist Lock connector from the LSG MK II into the controlling power source (i.e. control port on the rear panel of the Power Fog Family of Ultratec Special Effects Foggers). This port can be controlled via DMX, the Timer/ Duration Remote or the Show Control Remote. - Page 8 9. Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the temperature. 10. After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect hoses.
-
Page 9: Operation Procedure Lsg Mk Ii Low Pressure W/ 350Lbs Dewar Tank
2. Connect the grey Twist lock connector from the LSG MK II into the controlling power source (i.e. control port on the rear panel of the Power Fog Family of Ultratec Special Effects Foggers). This port can be controlled via DMX, the Timer/ Duration Remote or the Show Control Remote. - Page 10 10. Verify cool temperature output by using your hand and passing it through the fog-CO2 output noting the temperature. 11. After use, turn off the valves and trigger the LSG MK II to depressurize the system before attempting to disconnect the hoses.
-
Page 11: Options
Solid Light: Indicates that the unit is ready to fog at full output. No Light: Indicates problems; a loss of power or remote is not connected. If these fail to correct the problem, contact your local Ultratec Special Effects dealer. www.ultratecfx.com... -
Page 12: Show Control Operation
No Light: Indicates problems; a loss of power or remote is not connected. If these fail to correct the problem, contact your local Ultratec Special Effects dealer. Note: To operate the LSG MK II using the Timer/ Duration Remote, the DMX Address must be set on 555 and the Duration control set over 50%. -
Page 13: Dmx Operation
The casing of the PFI is stainless steel with a powder paint coating. To clean simply wash with mild soap and warm water. Heat Exchanger Using high quality Ultratec Special Effects fluid should result in a long heat exchanger life. (See warranty policy outlined on the last page of this document). Recommended Fluid Director’s Choice Fog Fluid: The choice of professionals. -
Page 14: Warranty
RA number clearly marked on the outside of the box. Warning: Ultratec Special Effects considers all of it’s product to be safe for use in the application it was intended. Ultratec Special Effects takes no responsibility for misuse or incorrect use. Always refer to the Product Manual for proper use.