Connector Output Parameters - Siemens Sinamics G120 Series Parameter Manual
Hide thumbs
Also See for Sinamics G120 Series:
- List manual (1256 pages) ,
- Manual (732 pages) ,
- Operating instructions manual (550 pages)
Table of Contents
Advertisement
Parameters
Connector/Binector (BICO)-Parameters
1.4.4
Connector Output Parameters
r0020
r0021
r0024
r0025
r0026[0...1]
r0027
r0029
r0030
r0031
r0032
r0035[0...2]
r0036
r0037[0...1]
r0038
r0039
r0051[0...1]
r0061
r0062
r0063
r0064
r0065
r0066
r0067
r0068
r0069[0...5]
r0070
r0071
r0072
r0074
r0075
r0076
r0077
r0078
r0079
r0080
r0084
r0085
r0086
r0087
r0090
r0094
r0394
r0395
r0396
r0485
r0623[0...2]
r0630[0...2]
r0631[0...2]
r0632[0...2]
r0633[0...2]
r0755[0...1]
r0947[0...63]
r0949[0...63]
1-310
CO: Freq. setpoint before RFG / Setp before RFG
CO: Act. filtered frequency / Act. filt. freq.
CO: Act. filt. output frequency / Act. outp. freq
CO: Act. output voltage / Act.outp. volt
CO: Act. filtered DC-link volt. / Act. fil. Vdc
CO: Act. output current / Act. outp. cur
CO: Flux gen. current / Flux gen. cur.
CO: Torque gen. current / Torque gen.cur
CO: Act. filtered torque / Act fil torque
CO: Act. filtered power / Act fil. power
CO: Act. motor temperature / Act. mot.temp.
CO: Inverter overload utilization / Invert ovl util
CO: Inverter temperature [°C] / Inverter temp.
CO: Fil. power factor / Fil.power fact
CO: Energy consumpt. meter [kWh] / Energy meter
CO: Active Drive Dataset (DDS) / Active DDS
CO: Act. rotor speed / Act rotor speed
CO: Freq. setpoint / Freq. setpoint
CO: Act. frequency / Act. frequency
CO: Dev. frequency controller / Dev. freq ctrl
CO: Slip frequency / Slip frequency
CO: Act. output frequency / Act. outp freq
CO: Act. output current limit / Outp cur limit
CO: Output current / Output current
CO: Act. phase currents / Act. phase cur
CO: Act. DC-link voltage / Act. Vdc
CO: Max. output voltage / Max. outp.volt
CO: Act. output voltage / Act. outp.volt
CO: Act. modulation / Act modulation
CO: Current setpoint Isd / Cur. setp. Isd
CO: Act. current Isd / Act. cur. Isd
CO: Current setpoint Isq / Cur. setp. Isq
CO: Act. current Isq / Act. cur. Isq
CO: Torque setpoint (total) / Total trq setp
CO: Act. torque / Act. torque
CO: Act. air gap flux / Air gap flux
CO: Act. re-active current / Act.re-active cur
CO: Act. active current / Act.active cur
CO: Act. power factor / Act.power fact
CO: Act. rotor angle / Act rotor angle
CO: Transformation angle / Transf. angle
CO: Stator resistance IGBT [%] / Stat. res.IGBT
CO: Total stator resistance [%] / Total stat.res
CO: Act. rotor resistance / Act rotor res.
CO: Encoder counter value / Encoder count val.
CO: Display for the identified stator resistance / Act. stator resist
CO: Motor model ambient temperature / Mot. model amb. te
CO: Stator iron temperature / Stat.iron temp
CO: Stator winding temperature / Stat.wind.temp
CO: Rotor winding temperature / Rot. wind.temp
CO: Act. AI after scal. [4000h] / CO:AI scal[4000h]
CO: Last fault code / Last fault code
CO: Fault value / Fault value
© Siemens AG 2007 All Rights Reserved
SINAMICS G120 Control Units CU240S, Edition 05/2007
Hide quick links:
Advertisement
Chapters
Table of Contents
