Related Manuals for Zodiac Chlor Perfect
Summary of Contents for Zodiac Chlor Perfect
- Page 1 Instruc� ons for installa� on and use - English Redox regulati on Translation of the original instructi ons in french More documents on: www.zodiac.com H0435000.G - 2019/11...
- Page 3 WARNINGS GENERAL WARNINGS • Failure to respect the warnings may cause serious damage to the pool equipment or cause serious injury, even death. • Only a person qualifi ed in the technical fi elds concerned (electricity, hydraulics or refrigerati on) is authorised to perform this procedure. The qualifi ed technician working on the appliance must use/wear personal protecti ve equipment (such as safety goggles and protecti ve gloves, etc.) in order to reduce the risk of injury oc- curring when working on the appliance.
- Page 4 WARNINGS ASSOCIATED WITH ELECTRICAL APPLIANCES • The electrical supply to the appliance must be protected by a dedicated 30 mA differential residual current protection device (RCD), complying with the standards and regulations in force in the country where it is installed. •...
-
Page 5: Table Of Contents
The distribu� on or modifi ca� on of this document in any way is prohibited, without prior • authorisa� on from Zodiac®. Zodiac® is constantly developing its products to improve their quality. The informa� on • contained herein may therefore be modifi ed without no� ce. -
Page 6: ❶ Specifi Ca� Ons
❶ Specifi ca� ons 1.1 I Descrip� on Control box Sucti on cane Pipework installati on kit ORP sensor Threaded sensor holder Fixture collar Wall-mounti ng bracket kit 465 mV buff er soluti on 1.2 I Technical specifi ca� ons Power supply voltage 220-240 VAC-50 Hz - 1-phase Electric output... -
Page 7: I Dimensions And Marking
1.3 I Dimensions and marking Peristalti c pump Master switch BNC connector socket for ORP sensor Cable gland for direct coupling with the fi ltering system Connector for sucti on tube Connector for injecti on tube Cable gland for sucti on cane cable Cable gland for 230Vac/50Hz power cord... -
Page 8: ❷ Installa� On
❷ Installa� on 2.1 I Preparing the pool 2.1.1 Water balance It is essenti al that the pool water balance is controlled and adjusted before installing the appliance. Making sure that the pool water balance is correct from the very start will reduce the likelihood of encountering problems on the fi rst days of operati on or during the season the pool is in use. - Page 9 2.1.2 Appliance injecti on programme Example of 4 injecti on cycles with a set point at 650 mV: • ORP ≥ 580 mV: 20% injecti on (2 min) & 80% pause (8 min) • ORP ≥ 510 mV: 50% injecti on (5 min) & 50 % pause (5 min) •...
-
Page 10: I Hydraulic Connecti Ons
2.2 I Hydraulic connec� ons 2.2.1 Sensor and injecti on point locati on • The ORP sensor must be installed more than 30 cm before or a� er a piping bend. Use the op- ti onal POD kit if necessary. Failing to follow this positi oning can lead to incorrect or unstable measurements. - Page 11 2.2. Sensor and injecti on point installati on • There must be at least 60 cm linear between the sensor and the injecti on point. If this is not possible, use the POD kit available as an opti on or a check valve. •...
-
Page 12: I Electrical Connecti Ons
2.3 I Electrical connec� ons • Only power on the appliance once all connec� ons (electrical and hydraulic) are complete. • Using the supplied fi xture kit, install the control box on a rigid, verti cal surface in an easy-access locati on. •... -
Page 13: ❸ Use
❸ Use 3.1 I Control box presenta� on Acti vate sensor calibrati on mode (press and hold for 5 seconds) Confi rm a choice in the "Setti ngs" menu Cancel the "OFA" over feed alarm View the set point value (press and hold for 5 seconds) Exit the "Setti ngs"... -
Page 14: I Calibrati Ng The Sensor
3.3 I Calibra� ng the sensor • For the appliance to operate accurately and reliably, the ORP sensor must be calibrated regularly (on installa� on, on re-commissioning a� er wintering, and every 2 months when in use). • Don’t wipe the sensor or touch its � p! •... -
Page 15: I Setti Ngs
3.6 I Se� ngs 3.6.1 "Se� ngs" menu Menu Default setti ngs Language French Set point 650 mV "Boost" mode durati on 10 minutes "OFA" over feed alarm 4 hours Calibrati on Acti vated "On" Filtering operati on detecti on Acti vated "On"... - Page 16 3.6.3 "Set point" menu 2 methods for adjusti ng the set point: • see § "3.6.1 "Setti ngs" menu" • Press when the appliance is running: • Press and hold and adjust the set point using the keys. • Release the key to exit.
- Page 17 3.6.6 "Calibra� on" menu This functi on can be removed (we advise strongly against this, except in the case of pools under a maintenance contract). 3.6.7 "Filtering" menu This appliance is fi tt ed with a double electric power supply making it possible to keep the appliance switched on to carry out ORP sensor calibrati on when fi ltering is not operati onal.
-
Page 18: ❹ Maintenance
❹ Maintenance 4.1 I Changing the peristal� c tube • Remove the peristalti c pump cover, • Place the roller holder at "10:20" by turning it clockwise, • Completely free the le� fi tti ng by keeping it stretched outwards, •... -
Page 19: ❺ Troubleshoo� Ng
❺ Troubleshoo� ng • If a problem occurs, before you contact your retailer, please carry out these few simple checks using the following tables. • If the problem con� nues, contact your retailer. • : Ac� ons to be performed by a qualifi ed technician only 5.1 I Appliance behaviour Behaviour Possible causes... -
Page 20: I Displays
5.2 I Displays Message Possible causes Soluti ons • Corrector product container • Replace the corrector product container empty "Level Low" • Floater blocked • Check that the white fl oater on the sucti on cane is in working order •... - Page 21 Your retailer Modèle appareil Appliance model Numéro de série Serial number Pour plus d’informations, enregistrement produit et support client : For more information, product registration and customer support: www.zodiac.com ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.