Related Manuals for Kenwood KDC-U7056DAB
Summary of Contents for Kenwood KDC-U7056DAB
- Page 1 KDC-U7056DAB KDC-U7056BT KDC-U7056BTL CD-RECEIVER Quick Start Guide © 2012 JVC KENWOOD Corporation B59-2188-10/01 (M)
-
Page 2: Table Of Contents
Cleaning the connector Specifications .............21 The unit may not function properly if the About the Quick Start connector between the unit and faceplate are dirty. Detach the faceplate and clean the Guide connector with a cotton swab gently, being careful not to damage the connector. This Quick Start Guide describes basic functions of this unit. Connector For functions not described in this Guide, refer to the Instruction Manual on the following website: Condensation manual.kenwood.com/edition/im362/ When the car is air-conditioned, moisture may collect on the laser lens. This may cause disc read errors. In this case, remove the disc and wait for the moisture to evaporate. Notes • If you experience problems during installation, consult your Kenwood dealer. • When you purchase optional accessories, check with your Kenwood dealer to make sure that they can work with your model To refer to the Instruction Manual, a browser and in your area. such as Internet Explorer® 7 or later, Firefox® • Characters that conform to ISO 8859-1 3.6 or later, Chrome™ 20 or later, Safari® 5.1 can be displayed. -
Page 3: How To Reset Your Unit
• To display characters in the following How to reset your unit language, additional setting is required. If the unit fails to operate properly, press the KDC-U7056DAB KDC-U7056BT Reset button. The unit returns to the factory - Chinese settings. Refer to “Chinese” of <12-5. Initial Reset button settings>. KDC-U7056BTL - Arabic - Persian - Thai Refer to “TAG Language” of <12-5. Initial settings>. About the discs used with this unit • This unit can only play the CDs with • The following discs cannot be used: - A disc that is not round - A disc with coloring on the recording surface or a disc that is dirty... -
Page 4: Appendix
FAT12, FAT16, FAT32 The online manual about Before using this unit for the first audio files is put on the site, time www.kenwood.com/cs/ce/audiofile/. When this unit is first turned on, the Models of iPods/iPhones that can interactive menu appears for setting the interface language and demonstration be connected to this unit mode. - Page 5 [Control] knob (Volume knob) [ 1 / 6 ] Release Adjusting the clock Detaching/ Attaching the faceplate Press [Control] knob to enter the Function setting mode. The item can be selected and determined as follows. ”Settings” Á “Clock & Date” Á “Clock Adjust” Turn [Control] knob to select the item, Press the Release button. and press [Control] knob. Turn [Control] knob to adjust the hour, and then press [Control] knob. Turn [Control] knob to adjust the minute, and then press [Control] knob. Press and hold [ 1/6] to exits the Function setting mode. • Remove the faceplate at once after pressing the Release button; otherwise it can fall down due to vibration. • The faceplate is a precision component of the unit and can be damaged by shocks or jolts.
-
Page 6: General Operations
[Control] knob (Volume knob) Auxiliary input Power Bluetooth audio “BT AUDIO” To turn the power ON, press [SRC]. “CD” To turn the power OFF, press and hold Auxiliary Input “AUX” [SRC]. T his source can be selected only when it can be played. Source selection Function of KDC-U7056DAB. Function of KDC-U7056BT. Pressing [SRC] repeatedly switches among sources. Volume Source Display Turn [Control] knob to adjust the sound Standby “STANDBY” volume. Digital radio “DIGITAL RADIO” USB terminal Tuner “TUNER”... -
Page 7: Playing Music (Cd/Usb/Ipod)
Playing music (CD/USB/iPod) Disc slot CA-U1EX [ G ] Disc slot cover [Control] knob KCA-iP102 [ 1 / 6 ] [ E / F ] [ R / S ] REAR USB indicator USB Terminal Playing a disc Pause and play a song (track or Open the Disc slot cover upward. -
Page 8: Listening To The Radio/Digital Radio
[SRC] [Control] knob [ 1 / 6 ] [ E / F ] Selecting a tuner source Turn [Control] knob to select preset number (FM/ Digital Radio: “1” – “18”, Press [SRC] to select “TUNER” or “DIGITAL AM: “1” – “6”), and then press and hold RADIO” (KDC-U7056DAB only). Refer to [Control] knob. <Source selection> (page 6). Recalling the stations in the Selecting a band (FM or AM) memory (Tuner only) Press [R]. Press [R] to select a band. (Tuner only) Selecting a station/ service Press [1/6]. -
Page 9: Hands-Free Phoning
Hands-free phoning [Control] knob [ Ú ] Dialing a number in the phone Pairing a Bluetooth device You can pairing your Bluetooth device in book this unit. Dial the phone number in the phone book of your cell phone. Operate the Bluetooth device to request If the phone book has not been this unit for connection. -
Page 10: Before Installation
Metal parts such as the heat sink and • If the console has a lid, make sure to enclosure become hot. install the unit so that the faceplate will • Mounting and wiring this product not hit the lid when it is closed or opened. requires skills and experience. For safety’s • After the installing the unit, check sake, leave the mounting and wiring work whether the brake lamps, blinkers, wipers, to professionals. etc. on the car are working properly. • If you experience any problem during • Mount the unit so that the mounting installation, consult your Kenwood dealer. angle is 30° or less. • Disconnect the battery’s negative terminal • Reception may become poor if there are before installing the unit. metal objects near the Bluetooth antenna. • Insulate unconnected wires with vinyl tape or other similar materials. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires and terminals. Bluetooth antenna unit • Be sure to ground this unit to the car’s chassis again after mounting. • If the fuse blows, first make sure the wires... - Page 11 KDC-U7056DAB • This unit has the cooling fan to decrease the internal temperature. Do not mount the unit in a place where the cooling ..4 fan of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction. Cooling fan ..4 For Good Reception ..1 (3m) To assure good reception, note the following: • Communicate with the cell phone within the line-of-sight distance of 10 m (30 ft). The communication range becomes ..1 shorter depending on the surrounding environment. The communication range also becomes shorter when there is an obstacle between this unit and the cell phone. The above maximum ..1 communication range (10 m) is not always assured. • A broadcast station or walkie-talkie located nearby can interfere with communication due to a too strong signal..3 Installation accessories ..1...
-
Page 12: Connecting Wires To Terminals
Connecting wires to terminals Rear output Front output Subwoofer output Fuse (10A) FM/AM antenna input Digital radio antenna (Accessory7) (KDC-U7056DAB only) Wiring harness Microphone (Accessory5) (Accessory1) (KDC-U7056BT/ KDC-U7056BTL only) White White/Black To front left speaker Gray To front right speaker Gray/Black Green Green/Black To rear left speaker Purple To rear right speaker Purple/Black < Ignition key • Speaker Impedance: 4 – 8 Ω switch Car fuse Red (Ignition wire) Yellow (Battery wire) Car fuse box (Main fuse) Black (Ground wire) · (To car chassis) –... - Page 13 USB connector (0.8m) To USB device. USB maximum power supply current : DC 5 V = 1 A Microphone (Accessory5) (KDC-U7056DAB only) If no connections are made, do not let the wire come out from the tab. Blue/White (Power control wire) When using the optional power amplifier, connect this wire to its power control terminal. P.CONT Depending on what antenna you are using, connect either to the control terminal of the motor antenna, Blue (Antenna control wire) or to the power terminal for the booster amplifier of ANT. the film-type or short pole type antenna. CONT (Max. 300mA, 12V) Brown (Mute control wire) When connecting to the Kenwood navigation system: Refer to your navigation manual. MUTE Orange/ White (Dimmer control wire) To car light control switch. ILLUMI Light Blue/ Yellow To use the steering wheel remote control feature, (Steering remote control wire) an exclusive remote adapter (not supplied) that REMOTE CONT matches your car is required. STEERING WHEEL REMOTE INPUT...
-
Page 14: Way Speaker System Setup
3 way speaker system setup Connect the speaker wires Tweeter output Mid Range output Woofer output Wiring harness (Accessory1) White White/Black To MID Range left speaker Gray To MID Range right speaker Gray/Black Green Green/Black To left Tweeter Purple To right Tweeter Purple/Black Blue/White (Power control wire) When using the optional power amplifier, P.CONT connect this wire to its power control terminal. If no connections are made, do not ⁄ let the wire come out from the tab. ¤ Select a crossover mode according to how the speakers are connected. Refer to <2-Way/3-Way Crossover Setting> (next page). For how to connect speaker wires ⁄... - Page 15 2-Way/3-Way Crossover Setting Select a crossover mode 2-way or 3-way according to how the speakers are connected. Press the [SRC] to select “STANDBY”. Pressing down the [S] and [E]s for at least 3 seconds, allows you to enter the 2-way/3-way crossover setting mode. The currently selected crossover mode is displayed. To change it, turn [Control] knob to select “YES”, and then press [Control] knob. A confirmation screen appears. If you are sure you want to change the crossover mode, turn the [Control] knob to select “YES”, and then press the [Control] knob. The newly selected crossover mode is displayed, canceling the 2-way/3-way crossover setting mode. English | 15...
-
Page 16: Installing/Removing The Unit
Installing/Removing the unit Non-Japanese cars Removing the trim plate Engage the catch pins on the extraction key (Accessory2) and release the two locks on the upper part of frame. Lift up and pull the frame forward as shown in the figure. Catch Bend the tabs of the mounting sleeve Lock with a screwdriver or the like and attach it in place. < Accessory When the upper part of frame is • Make sure that the unit is installed removed, remove the lower part of frame. securely in place. If the unit is unstable, it <... -
Page 17: Installing The Microphone Unit
KDC-U7056DAB only Installing the Installing the Digital Microphone unit radio antenna CAUTION Check the installation position of the microphone (Accessory 5). • This film antenna is exclusively for use inside the vehicle. Clean the installation surface. • Do not install at the following locations: Install the microphone. - Where it may block driver’s view Lay the cable up to the unit with it - Where it may obstruct operation of secured at several positions using tape safety devices such as air bags or the like. - On movable glass surface such as rear < hatch • Signal strength will decrease at the • Install the microphone as far as possible following locations: from the cell phone. - On IR reflecting glass or where covered... -
Page 18: Installation Overview
KDC-U7056DAB only Installing the Digital radio antenna Installation overview Determining the antenna installation location • When installing the antenna on the left side Accessory Front pillar 150 mm Earth sheet Antenna cable (3.5 m) 70 mm* • The antenna should be installed on the Accessory passenger side for safety. - Page 19 Antenna Installation After pasting, rub the element in the glass surface in the direction of the arrow Check the installation location. shown in the figure to bond it. Clean the area where antenna film (Accessory 6), amplifier unit (Accessory 7), and earth sheet are pasted with the included cleaner (Accessory 9). The coating on the metal surface need not be removed. • Wait until the glass surface is completely dry before pasting. • If the glass surface is cold, such as during winter, warm it with defroster or dryer. Remove the separator (tag I) of antenna film horizontally and paste the antenna Remove the application film (tag III). on the front glass. • Do not touch the feeder terminal of the element. Also, do not apply any glass cleaner. Feeder terminal Match the protrusion of the amplifier with the 5 on the antenna film and paste. • Remove the separator gently. • Do not touch the feeder terminal or • Do not touch the pasting surface the pasting surface (adhesive side) of (adhesive side) of the antenna film. the amplifier.
- Page 20 KDC-U7056DAB only Installing the Digital radio antenna < • When installing the antenna on the left side • Take the following precautions when Accessory passing the antenna cable inside the front pillar where the air bag is installed. Accessory - Install the amplifier part of the antenna cable in front or above the air bag so Earth sheet that the antenna and the air bag do not interfere. Match the protrusion with 5 Accessory Remove the film covering the earth sheet and paste the earth sheet on the metal part of the vehicle. Air bag...
-
Page 21: Specifications
Band11 : 6.3 kHz ±9 dB, Band12 : 10 kHz ±9 dB AM tuner section Band13 : 16 kHz ±9 dB Frequency range 10 kHz step : 5 30 kHz – 1700 kHz Bluetooth section 9 kHz step : 5 31 kHz – 1611 kHz Version : B luetooth Ver. 2.1+EDR Certified Usable sensitivity (S/N = 20dB) : 3 1 dBµ (36 µV) Frequency range : 2.402 – 2.480 GHz Output Power DAB tuner section (KDC-U7056DAB) : + 4dBm (MAX), 0dBm (AVE) Power Class 2 Frequency range Maximum Communication range L-BAND : 1452.960 MHz – 1490.624 MHz : Line of sight approx.10m BAND III : 174.928 MHz – 239.200 MHz Profiles Sensitivity : - 100 dBm : HFP (Hands Free Profile) Signal to Noise ratio : 80 dB... - Page 22 Requirements Pandora: Requirements Aha™: Requirements for listening to the Pandora Requirements for listening to the Aha™ are are as follows: as follows: iPhone or iPod touch iPhone or iPod touch • Use an Apple iPhone or iPod touch • Use an Apple iPhone or iPod touch running under iOS3 or later. running iOS4 or later. • Search for “Pandora” in the Apple iTunes • Search for “aha” in the Apple iTunes App App Store to find and install the most Store to find and install the most current current version of the Pandora application version of the Aha™ application on your on your device. device. • iPhone/ iPod touch connected to this unit • iPhone/ iPod touch connected to this unit with a KCA-iP102. with a KCA-iP102. Android™ or BlackBerry® Android™...
-
Page 23: Class 1 Laser Product
The marking of products using lasers (Except for some areas) CLASS 1 • The Bluetooth word mark and logos are LASER PRODUCT owned by the Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation The label is attached to the chassis/case and is under license. Other trademarks and trade names are those of their respective owners. says that the component uses laser beams • The “AAC” logo is a trademark of Dolby that have been classified as Class 1. It means Laboratories. that the unit is utilizing laser beams that • “Made for iPod” and “Made for iPhone” are of a weaker class. There is no danger of mean that an electronic accessory has been hazardous radiation outside the unit. designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note REGISTERED No. : ER0106384/13 that the use of this accessory with iPod or iPhone may affect wireless performance.