Advertisement
Quick Links
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT
INTRODUCTION
This remote control system was developed to provide safe, reliable, and user-friendly remote control system for gas heating appliances.
The system can be operated manually from the transmitter. The system operates on one of 65,536 security codes that are programmed
into the transmitter at the factory.
TRANSMITTER
f i r e - p a r t s . c o m
SIGNAL
LIGHT
ON
ON/OFF
OFF
BUTTONS
FRONT
RECEIVER
The remote receiver operates on (4) AA-size 1.5V batteries. It is recommended that ALKALINE batteries be used for longer battery life
and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential for proper operation of the
remote receiver.
The remote receiver houses the microprocessor that responds to commands from the transmitter to control system operation. The
remote receiver has a 3-position slide switch for selecting the MODE of operation: ON/REMOTE/OFF
With the slide switch in the ON position (toward the LEARN button), the system will
•
remain on until the slide switch is placed in the OFF or REMOTE position.
With the slide switch in the REMOTE position (centered), the system will only operate
•
if the remote receiver receives commands from the transmitter.
With the slide switch in the OFF position (away from the LEARN button), the system
•
is OFF.
It is suggested that the slide switch be placed in the off position if you will be
•
away from your home for an extended period of time. If the remote receiver is
mounted out of children's reach, placing the slide switch in the OFF position
also functions as a safety "lock-out" by both turning the system off and
rendering the remote receiver inoperative.
___________________________________________________________________________________________________________
Rasmussen SR-MV1
Model: SR-MV1
INSTALLATION AND OPERATING INSTRUCTIONS
ATTEMPT TO INSTALL OR OPERATE
12V
BATTERY
COMPARTMENT
BACK
The transmitter operates on a 12V battery (included) made specifically for remote
controls and electronic lighters. Install the 12V battery supplied with the
transmitter into the battery compartment.
It is recommended that AKALINE batteries always be used for longer battery life
and maximum operational performance.
The transmitter has ON and OFF functions that are activated by pressing either
button on the face of the transmitter. When a button on the transmitter is
pressed, a signal light on the transmitter illuminates briefly to verify that a signal
has been sent. Upon initial use, there may be a delay of three seconds before
the remote receiver will respond to the transmitter. This is part of the system's
design. If the signal light does not illuminate, check the position of the
transmitter's battery.
Requires 4-AA 1.5V
alkaline batteries
Learning
button
Slide
Switch
ON
REMOTE
OFF
Remote Receiver
REV 3/15/12 Page 1 of 4
Advertisement
Related Manuals for Rasmussen SR-MV1
Summary of Contents for Rasmussen SR-MV1
- Page 1 Model: SR-MV1 INSTALLATION AND OPERATING INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote control system was developed to provide safe, reliable, and user-friendly remote control system for gas heating appliances.
- Page 2 The remote receiver can be placed on the fireplace hearth or under the fireplace, behind the control access panel. Position where the ambient temperature inside the receiver case does not exceed 130 NOTE: Black Slide Button is used for Hearth Mount applications. ___________________________________________________________________________________________________________ Rasmussen SR-MV1 REV 3/15/12 Page 2 of 4...
- Page 3 When you release the LEARN button the receiver will emit an audible “beep”. After the receiver emits the beep press the transmitter ANY button and release. The receiver will emit several beeps indicating that the transmitter’s code has been accepted into the receiver. ___________________________________________________________________________________________________________ Rasmussen SR-MV1 REV 3/15/12 Page 3 of 4...
- Page 4 FCC REQUIREMENTS NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. ___________________________________________________________________________________________________________ Rasmussen SR-MV1 REV 3/15/12 Page 4 of 4...