Advertisement
Quick Links
R
ECTANGULAR
Congratulations!
purchased a high quality stereo
loudspeaker.
When matched to
comparable electronic equipment,
expect years of quality high fidelity
sound. We are constantly striving
to provide the very best technology
has to offer.
The following manual is designed
to give you, the installer or owner,
basic
information
as
speaker's installation and operation.
It is beyond the scope of this
manual to go into all the details that
must be taken into consideration in
a sophisticated high fidelity system.
If you have any further questions
regarding this speaker which are
not answered by this manual,
please feel free to contact your
local dealer.
GENERAL DESCRIPTION
The
5
1/4"
two-way
speaker
has
two
magnetically
shielded 5 1/4" Woven Kevlar
woofers with linear long throw butyl
rubber edge surrounds. Pivoting 1"
lens-free
aluminized
cooled dome tweeters are utilized
for
excellent
high
dispersion throughout the entire
listening environment.
Cut-out Dimensions
Width
7 7/8"
Height
14 7/16"
Depth
3 1/2"
SHIPPING DAMAGE
Each speaker is thoroughly tested
before
it
leaves
the
However, in shipment, accidents
may occur.
Please inspect your
speakers
carefully
5 1/4" 2-W
You
have
receive them to make sure there is
no damage.
notify your dealer, or supplier
immediately for assistance. If you
received your speakers by public
transportation, report the damage at
once.
AMPLIFIER OPERATION
to
the
The 5 1/4" two-way LCR speaker
is
equipped
automatic polyswitch circuit which,
when overdriven, will automatically
restrict electrical current to the
tweeter to prevent damage.
circuit will automatically re-engage
once the volume is turned down or
the problem is removed.
normally takes about thirty (30)
seconds to occur.
The speaker will perform well with
amplifiers from 15 to 150 Watts
RMS. However, any speaker can
LCRS
be
damaged
circuitry engaged by any size
amplifier that is being overdriven
into clipping. "Amplifier clipping" is
a phrase used to describe a
ferro-fluid
condition when, because of the
volume demand, an amplifier is
frequency
being asked for more power than it
can give.
your protective circuits on the
tweeter are activated often, please
consider reducing the volume at
which
speaker or purchasing a larger
amplifier with more reserve power.
DAMAGE DONE TO A SPEAKER
BY CLIPPING IS NOT COVERED
UNDER THE WARRANTY.
SPEAKER PLACEMENT
Placement of the Wall Mounted
Speakers in your room should be
carefully considered. They should
be located where they will provide
you with the best possible sound
and
installation.
factory.
It is beyond the scope of this
publication to discuss all of the
various
when
you
placement.
contact your dealer.
MTM S
AY
If there is, please
with
a
special
or
its
protective
If you should find that
you
normally
play
the
greatest
ease
aspects
of
speaker
Please feel free to
PS-525 LCRS
PEAKER
15 3/4"
The
3 1/2"
5 1/4" LCRS
This
WIRING
To achieve maximum performance
from
your
strongly suggest the use of special
low inductance stereo cable. There
are many good brands presently on
the market. The cable should be 16
gauge or larger.
smaller than 16 gauge, which is
sometimes
d e c r e a s e
performance. The larger the wire
is, the better. For a proper and safe
installation it is important when
the
installing your speakers and/or
running wire through your house
that you adhere to all local codes
and regulations. We suggest that a
professional be consulted in order
to
maximize
performance.
h o w e v e r ,
suggestions:
1. Try to keep the wire length to a
minimum. Runs of over 50 feet
should have 16 gauge or heavier
wire.
of
2. Avoid routing speaker cables
immediately parallel to electrical
cables.
This will help reduce
hum and RF
9"
new
speakers,
we
Speaker wire
clear
coated,
will
y o u r
s p e a k e r ' s
your
system's
The
following,
a r e
j u s t
a
f e w
interference.———
Advertisement
Related Manuals for OEM Architech PS-525
Summary of Contents for OEM Architech PS-525
- Page 1 If you received your speakers by public transportation, report the damage at once. AMPLIFIER OPERATION The 5 1/4" two-way LCR speaker equipped with special automatic polyswitch circuit which, when overdriven, will automatically restrict electrical current to the tweeter to prevent damage.
- Page 2 (+ & -). Do not over tighten these screws OEM Systems Company, Inc. www.oemsystems.com Install the frame and mounting better ring assembly by passing the black mounting ring through the cut-out as illustrated above (see figures 1 &...