Page 1
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SERVICE MANUAL AE-6Y CHASSIS MODEL MODEL COMMANDER DEST CHASSIS NO. COMMANDER DEST CHASSIS NO. KP-44PX3 KP-44PX3U RM-945 SCC-Q85K-A RM-945 SCC-Q84U-A KP-44PX3 RM-945 PROJECTION TV - 1 -...
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE AN ISOLATION TRANSFORMER SHOULD BE USED DURING THESE COMPONENTS WITH SONY PARTS WHOSE PART ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 l l a . s l . s l . s l . s l . s l e i l i n i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SECTION 1 SELF DIAGNOSIS FUNCTION AE-6Y Self Diagnostic Software The identification of errors within the AE-6Y chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SECTION 3 DISASSEMBLY 3-1. REAR COVER REMOVAL 3-2. SPEAKER BRACKET REMOVAL Rear cover Speaker bracket Six Screws Thirteen screws 3-3. MAIN BRACKET BLOCK REMOVAL 3-4. SERVICE POSITION Two screws Main bracket block...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 3-5. FRONT PANEL REMOVAL 3-6. H1 BOARD REMOVAL Four screws H1 Board 3-7. F1 BOARD REMOVAL 3-8. FRONT SPEAKERS REMOVAL 1 Speakers 1 Three Screws (+BVTP 4x16) F1 Board – 17 –...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 3-11. AD AND D BOARD REMOVAL 1 AD board Screw (+BVTP 3x12) D board 3 Three claws 3-12. G BOARD REMOVAL Five claws 2 G board – 19 –...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 3-13. A BOARD REMOVAL 3-14. HIGH_VOLTAGE CABLE REMOVAL AND INSTALLATION (1) Removal 3 B board 2 A board Rubber cap HV cable turn 90 (2) Installation Rubber cap HV cable Four claws...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SECTION 4 SET-UP ADJUSTMENTS 4-3. SCREEN (G2) ADJUSTMENT 4-1. SCREEN VOLTAGE ADJUSTMENT (ROUGH ALIGNMENT) Turn on the power of the set. Select VIDEO1 mode without signals. Receive the Monoscope signal. Supply DC 175 ±0.5 V from external power supply to Set 50% BRIGHTNESS and minimum PICTURE.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 4-5. 2-POLE MAGNET ADJUSTMENT 4-7. GREEN, RED AND BLUE FOCUS ADJUSTMENT Receive the Dot signal and set PICTURE to 80%, BRIGHTNESS to 50%. 4-7-1. Green, Red and Blue Lens Focus Place the caps on the red and blue lens so that only the Adjustment green color is shown.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SECTION 5 SAFETY RELATED ADJUSTMENT When replacing the following components marked with below D BOARD – CONDUCTOR SIDE – always check hold-down voltage and if necessary re-adjust. CN8015 Part Replaced (...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 SECTION 6 ELECTRICAL ADJUSTMENTS 6-1. Adjustments with Commander 6-1-2. Programming the Remote Commander for Operation in Service Mode Service adjustments to this model can be performed using the supplied remote Commander RM-945.
Page 25
All manuals and user guides at all-guides.com KP-44PX3 RM-945 c t i t l i – 25 –...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 6-1-4. Service List (Projector Engine) : Fixed data. xxxx : Cannot change. Standard Data Item Name/Description Data Range NTSC Name Wide Zoom 14 : 9 Smart Wide Zoom 14 : 9 Smart...
Page 27
All manuals and user guides at all-guides.com KP-44PX3 RM-945 Standard Data Item Name/Description Data Range NTSC Name Wide Zoom 14 : 9 Smart Wide Zoom 14 : 9 Smart SOGV –128 ~ 127 GREEN vertical skew offset data for Auto Regi.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 Adjust “V-Size” and “H-Size” so that the picture size is 6-2. Registration Adjustments within the specification. 6-2-1. Setup for Adjustment SPEC Overscan Spec. = 7.5% 1. Marking Input Signal H SIZE...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 6-2-3. Operation Method for Projector Engine Mode Commander Function Buttons Mode Description WRITE Writes data to NVM. TV STANDBY VIDEO STANDBY 7 + - READ Reads data from NVM. 5 + - Service data initialization.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 6-2-4. Projector Engine Adjustment 3. Operation Method for Fine Adjustment (Sub Deflection Adjustment) (in GRN, BLU, or RED Mode) Select the Projector Engine mode. a a a a a : Yes Adjustment –...
Page 31
All manuals and user guides at all-guides.com KP-44PX3 RM-945 Select “GRN SIZE”, and adjust so that each distance from 12. Select “GRN MSIZ”, and correct the space intervals for center to left end and to right end is equal. Adjust so that the horizontal section of the screen are equal.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 3. Red Adjustment 6-4. WHITE BALANCE ADJUSTMENT Place a cap on the blue lens so that green and red colors 1. Enter the monoscope signal. are displayed. 2. Press “MENU” button on the commander to enter the Press “3”...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 6-7. AUTO CONVERGENCE ERROR CODE LIST If an error code is displayed after the set has been fully adjusted, correctly, plese check the following items : position, tilt and sizing. If either of these adjustments are off, even slightly, the auto registration pattern will not hit the four sensors properly. This occurs when the internal generator patterns is being flashed on the screen for the sensor to read.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 6-8. TEST-TEST MODE Is available by pressing “OSD”, “5”, “Volume minus”, “TV” button in the standby mode, OSD “TT--” appears. The functions described below are available by pressing the two numbers. To release the Test-Test mode, Press “-” twice or switch the TV set into standby mode.
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (1) TUNER TU1100 AGC DEFEAT SWITCH IC2000 FROM B BOARD Q1100 SOUND PROCESSOR CONNECTOR IC2200 AUDIO AMP J2200 REAR-R POWER FM/AM SPEAKER REAR-L CN6400 CN6401 F6400 AC IN AC OUT CVBS ANALOG RF IC2500 X2000...
Page 36
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (2) IC9407 D-A CONVERTOR B CLK IC9420 IC9401 B CLK DF FILTER DSP PJE W CLK 1 W CLK OUT C D FOCUS OUT C B CLK RV OUT 1 W CLK 1 GV OUT 1 DF-V...
Page 37
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (3) CN3100 KEY 2 B 1/2 ( IC0001 B 2/2 ( BACKEND/SCANRATE/ BACKEND/SCANRATE/ IR-DATA OCP-OVP LVDS/A-INTERFACE P2.15 LVDS/A-INTERFACE LUMISPONDER OCP-FLAG P2.14 EPG MODE EPG-MODE P2.11 OCP-OVP IR DATA P2.9 OCP-FLAG SIRCS P2.8 MAIN-SW...
Page 38
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (4) CN3601 IC3600 RIGHT OUT AUDIO/VIDEO SWITCH BUFFER V-OUT-35 V-OUT-3B RIGHT IN V-OUT-15 LAST RF SC3-IN-R Q3656 AV3 IN R LEFT OUT V-OUT-25 AV2 OUT CVBS SC2-IN-R AV2 I R LEFT IN CVBS/Y MAIN BUFFER...
Page 39
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (5) TO FOCUS BLOCK TO FOCUS BLOCK TO FOCUS BLOCK CN9000 CN9300 CN9600 CR ( CG ( CB ( TO FBT TO FBT TO FBT RGB OUT RGB OUT RGB OUT CN9007 CN9307 CN9607...
All manuals and user guides at all-guides.com 7-1. BLOCK DIAGRAMS (6) 7-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM : SOLID CN8007 FPRD : NON FLAMMABLE CARBON V DEF- TO DY (R) V RET CN8025 FUSE : NON FLAMMABLE FUSIBLE IC8003 CN8008 V DRV+...
All manuals and user guides at all-guides.com B-#SSAE6Y<...>-A..-44PX3 TO WOOFER C2515 0.01 0.47 0.47 0.47 100000PF MSD601 MSB709-RT1 100000PF MMDL914T1 MSB709-RT1 MSD601 R5270 MSD601 100000PF 15000PF MMDL914T1 TO J BOARD CN3604 SWITCH AV LINK CONVERTER SWITCH ~ A Board Schematic Diagram [ Audio, Deflection, J_Interface ] Page 1/3 ~ - 41 -...
Page 42
All manuals and user guides at all-guides.com B-#SSAE6Y<...>-A..-44PX3 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL BTF-EF411 33pf 10UH Tab Contact BA033T 3.3V REGULATOR 6.8k 100k 1.8V REGULATOR 150K ~ A Board Schematic Diagram [ Modem, A_Tuner, Regulators ] Page 2/3 ~ - 42 -...
Page 43
All manuals and user guides at all-guides.com TO D BOARD CN8029 TO F1 BOARD CN0982 TO D BOARD CN8025 3.3K 3.3K 0.01 5.6K TO D BOARD CN8031 B-#SSAE6Y<...>A..-44PX3 TO D BOARD CN8023 ~ A Board Schematic Diagram [ B_Interface, N_Interface, Dig_Tuner ] Page 3/3 ~ - 43 -...
All manuals and user guides at all-guides.com ~ A Printed Wiring Board Conductor Side A ~ ~ A Board Location Table (B Side) ~ - 44 -...
Page 45
All manuals and user guides at all-guides.com ~ A Printed Wiring Board Conductor Side B ~ ~ A Board Location Table (B Side) ~ ~ A Board Semiconductor Voltage Table ~ ~ A Board IC Voltage Table ~ - 45 -...
All manuals and user guides at all-guides.com B-#SSAE6Y<...>-AD.-44PX3 TP 2 TP 1 TP 3 TP 4 TP 6 TP •7 TP 8 TP 10 TP 9 TP 11 TP 5 ~ AD Board Schematic Diagram [ PJED, REGI Correction ] Page 1/2 ~ - 46 -...
Page 47
All manuals and user guides at all-guides.com B-#SSAE6Y<...>-AD.-44PX3 COMPARATOR COMPARATOR ~ AD Board Schematic Diagram [ PJED, REGI Correction ] Page 2/2 ~ - 47 -...
All manuals and user guides at all-guides.com ~ AD Printed Wiring Board Conductor side A ~ ~ AD Board Location Table (A Side) ~ ~ AD Board Waveforms ~ 4.9 Vp-p (500 kHz) 0.9 Vp-p (V) 4.9 Vp-p (8.9 MHz) 1.3 Vp-p (V) 4.9 Vp-p (H) 1.9 Vp-p (V)
Page 49
All manuals and user guides at all-guides.com AD Board IC Voltage Table ~ D Board Waveforms ~ 1.0 Vp-p (V) 56.0 Vp-p (V) 0.8 Vp-p (V) 5.4 Vp-p (H) 221.5 Vp-p (H) TP10 9.0 Vp-p (H) 1245 Vp-p (H) 22.8 Vp-p (V) 17.8 Vp-p (V) 38.3 Vp-p (V) TP11...
All manuals and user guides at all-guides.com TO VMB BOARD - CN9701 TP 2 TP 3 TP 1 TO A BOARD CN3011 TP 10 TP 9 TP 8 +210V TO CB BOARD CN9601 TP 13 TP12• TP 11 TO A BOARD CN3013 EL1Z TO A BOARD...
All manuals and user guides at all-guides.com B-#SSAE6Y<...>-G..-44PX3 POWER SUPPLY S1VB40 MAIN_STBY R6081 5.6k R6082 4.7k R6080 Q6007 MSB709-RT1 R6079 R6083 D6047 MMDL914T1 Q6008 R6084 MSD601-RST1 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL ~ G Board Schematic Diagram [ Power Supply ] ~ - 52 -...
All manuals and user guides at all-guides.com ~ G Printed Wiring Board Conductor side ~ ~ G Board Location Table ~ Note : Portions of the circuit contained within the marked areas as shown have high voltages present. Use care to prevent electric shock during inspection or repair.
All manuals and user guides at all-guides.com ~ B Printed Wiring Board Conductor Side A ~ ~ J Printed Wiring Board Conductor Side ~ 1-723-216-12 1-689-676-12 ~ B Printed Wiring Board Conductor Side B ~ 1-689-677-12 (1-723-217-12) 1-689-676-12 (1-723-216-12) - 56 -...
All manuals and user guides at all-guides.com ~ CB Board Schematic Diagram [ RGB Out ] ~ ~ H1 Board Schematic Diagram [ AV Input, HP Out ] ~ CB.-44PX3 TO J BOARD TO A BOARD CN3600 CN2300 R,G,B OUT CN9600 CN2912 CN2909...
All manuals and user guides at all-guides.com ~ CB Printed Wiring Board Conductor side ~ ~ VMB Printed Wiring Board Conductor side ~ ~ F1 Printed Wiring Board Conductor side ~ ~ H1 Printed Wiring Board Conductor side ~ - 59 -...
All manuals and user guides at all-guides.com ~ CG Board Schematic Diagram [ RGB Out ] ~ ~ VMR Board Schematic Diagram [ Velocity Modulation ] ~ CG.-44PX3 VMR-44PX3 CN9300 CN9101 R9101 VELOCITY MODULATION TO FBT R9310 R,G,B OUT TO F. BLOCK 560k 1/4W L9101...
All manuals and user guides at all-guides.com 7-6 IC BLOCK DIAGRAMS A BOARD IC2500 TDA7265 A BOARD IC6201/IC6210 BA033T REFERENCE VOLTAGE A BOARD IC6202 PQ1CG2032FZ Vout ON/OFF PWM COMP ON/OFF ERROR AMP Oadj Vref - 64 -...
Page 65
All manuals and user guides at all-guides.com A BOARD IC2000 MSP3411G SBUS Interface I2C Interface DEMODULATOR IDENT SCART Switching Facilities D BOARD IC8003 STV9379 FLYBACK GENERATOR POWER AMPLIFIER THERMAL PROTECTION G BOARD IC6004 SE135N-LF4 D BOARD IC8006/IC8007 NJM2903M - 65 -...
Page 66
All manuals and user guides at all-guides.com G BOARD IC6002 MCZ3001D Remote DVLD Internal Driver Sel=34v ref 5v Reg. 10v 15v/8v Level Shift Vsense Control Logic Latch Centre Timer CR BOARD IC9000 CG BOARD IC9300 CB BOARD IC9600 TDA6118JF BIAS CIRCUIT AND THERMAL PROTECTION - 66 -...
All manuals and user guides at all-guides.com KP-44PX3 SECTION 8 RM-945 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for The components identified by shading £...
All manuals and user guides at all-guides.com KP-44PX3 RM-945 8-2. CABINET BLOCK The components identified by shading £ and mark are critical for safety. Replace only with part number specified. 7-685-648-79 +BVTP 3X12 TYPE 2 IT3 7-685-663-79 +BVTP 4X16 TYPE 2 IT3 REF.NO.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 8-3. MAIN BRACKET BLOCK The components identified by shading £ and mark are critical for safety. Replace only with part number specified. 7-685-648-79 +BVTP 3X12 TYPE 2 IT3 7-685-663-79 +BVTP 4X16 TYPE 2 IT3 REF.NO.
All manuals and user guides at all-guides.com KP-44PX3 RM-945 8-4. PICTURE TUBE BLOCK The components identified by shading £ and mark are critical for safety. Replace only with part number specified. 7-685-663-71 +BVTP 4X16 TYPE 2 IT3 REF.NO. PART.NO DESCRIPTION REMARK REF.NO.
All manuals and user guides at all-guides.com SECTION 9 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page CR BOARD COMPLETE Parts List : ....................72 CB BOARD COMPLETE Parts List : ....................72 CG BOARD COMPLETE Parts List : ....................
Page 72
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1405-595-A CR Board Complete R9002 1-216-814-11 METAL CHIP 1/10W R9003 1-216-813-11 METAL CHIP 1/10W R9004 1-216-864-11 SHORT CHIP * 4-102-022-01 PIN(30), WIRE R9006 1-216-864-11 SHORT CHIP 4-382-854-01 SCREW (M3X8), P, SW (+)
Page 73
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK < IC > C9301 1-107-652-11 ELECT 10UF 20.00% 250V C9302 1-165-176-11 CERAMIC CHIP 0.047UF 10.00% 16V IC9600 6-704-806-01 IC TDA6118JF C9303 1-126-947-11 ELECT 47UF 20.00% 35V C9304 1-117-216-51 CERAMIC...
Page 74
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R9313 1-260-328-11 CARBON 1/2W Q9411 8-729-045-05 TRANSISTOR 2SA2005 R9321 1-216-826-11 METAL CHIP 2.7K 5% 1/10W Q9412 8-729-045-04 TRANSISTOR 2SC5511 R9323 1-249-409-11 CARBON 1/4W Q9413 8-729-010-29 TRANSISTOR MSD601-RST1 Q9414 8-729-010-05...
Page 75
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK C9109 1-107-636-11 ELECT 10UF 20.00% 160V R9118 1-249-393-11 CARBON 1/4W C9110 1-137-528-11 MYLAR 0.1UF 10.00% 250V R9119 1-216-839-11 METAL CHIP 1/10W C9111 1-107-826-11 CERAMIC CHIP 0.1UF 10.00% 16V R9120 1-216-821-11...
Page 78
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK IC9401 8-759-683-55 IC CM0017AF R9415 1-216-821-11 METAL CHIP 1/10W IC9402 8-759-682-41 IC M24C32-WMN6T(A) R9416 1-216-825-11 METAL CHIP 2.2K 5% 1/10W IC9403 8-759-352-91 IC PST9143NL R9417 1-216-809-11 METAL CHIP 1/10W...
Page 79
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R9466 1-218-871-11 METAL CHIP 0.5% 1/10W R9559 1-216-821-11 METAL CHIP 1/10W R9467 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W R9561 1-216-864-11 SHORT CHIP R9468 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W R9562 1-216-864-11...
Page 83
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK Q8029 8-729-010-29 TRANSISTOR MSD601-RST1 R8042 1-216-826-11 METAL CHIP 2.7K 5% 1/10W Q8030 8-729-010-05 TRANSISTOR MSB709-RT1 R8043 1-218-895-11 METAL CHIP 100K 0.5% 1/10W Q8031 8-729-010-29 TRANSISTOR MSD601-RST1 R8044 1-218-863-11 METAL CHIP...
Page 84
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R8097 1-214-808-11 METAL 1/2W R8151 1-218-847-11 METAL CHIP 0.5% 1/10W R8098 1-214-808-11 METAL 1/2W R8152 1-218-871-11 METAL CHIP 0.5% 1/10W R8100 1-216-475-21 METAL OXIDE R8153 1-218-847-11 METAL CHIP 0.5% 1/10W...
Page 85
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R8218 1-260-123-11 CARBON 100K 5% 1/2W C2606 1-164-227-11 CERAMIC CHIP 0.022UF 10.00% 25V R8219 1-249-377-11 CARBON 0.47 5% 1/4W C2607 1-162-964-11 CERAMIC CHIP 0.001UF 10.00% 50V R8220 1-216-821-11 METAL CHIP...
Page 90
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK < TRANSISTOR > JR6011 1-216-864-11 SHORT CHIP JR6012 1-216-864-11 SHORT CHIP Q0100 8-729-028-28 TRANSISTOR 2SK2036(TE85L) JR6014 1-216-864-11 SHORT CHIP Q0200 8-729-028-28 TRANSISTOR 2SK2036(TE85L) JR6015 1-216-864-11 SHORT CHIP Q0201 8-729-028-28...
Page 91
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R2026 1-216-809-11 METAL CHIP 1/10W R2512 1-216-835-11 METAL CHIP 1/10W R2029 1-216-864-11 SHORT CHIP R2514 1-216-826-11 METAL CHIP 2.7K 5% 1/10W R2030 1-216-864-11 SHORT CHIP R2515 1-216-833-11 METAL CHIP...
Page 92
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R5240 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R8014 1-216-809-11 METAL CHIP 1/10W R5257 1-216-809-11 METAL CHIP 1/10W R8015 1-216-809-11 METAL CHIP 1/10W R5258 1-216-833-11 METAL CHIP 1/10W R8016 1-216-809-11...
Page 94
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK < CONNECTOR > < TRANSISTOR > CN3100 1-794-244-11 CONNECTOR, DIN (PLUG) 96P Q0001 8-729-010-05 TRANSISTOR MSB709-RT1 CN3400 * 1-564-524-11 PLUG, CONNECTOR 9P Q0002 8-729-010-05 TRANSISTOR MSB709-RT1 CN3402 * 1-564-519-11 PLUG, CONNECTOR 4P...
Page 95
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R0014 1-216-805-11 METAL CHIP 1/10W R0072 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R0015 1-216-805-11 METAL CHIP 1/10W R0073 1-216-833-11 METAL CHIP 1/10W R0016 1-216-805-11 METAL CHIP 1/10W R0074 1-216-864-11...
Page 96
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R3311 1-216-864-11 SHORT CHIP R5510 1-216-809-11 METAL CHIP 1/10W R3314 1-216-821-11 METAL CHIP 1/10W R5511 1-216-809-11 METAL CHIP 1/10W R3315 1-216-821-11 METAL CHIP 1/10W R5512 1-216-838-11 METAL CHIP 1/10W...
Page 101
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.