Sony CPD-101VS Operating Instructions Manual
Trinitron multimedia computer display
Hide thumbs
Also See for CPD-101VS:
- Service manual (48 pages) ,
- Operating instructions manual (39 pages) ,
- Service bulletin (9 pages)
Related Manuals for Sony CPD-101VS
Summary of Contents for Sony CPD-101VS
- Page 1 3-864-163-13 (1) Trinitron Multimedia Computer Display Operating Instructions CPD-101VS CPD-201VS 1998 by Sony Corporation...
- Page 2 Cordon Type SVT ou SJT, minimum 3 Longueur Maximum 15 pieds As an NERGY TAR Partner, Sony Corporation has determined that this product meets the NERGY guidelines for energy efficiency. NERGY TAR is a U.S. registered mark. 18 AWG...
- Page 3 Declaration of Conformity Model Number : CPD-101VS CPD-201VS Trade Name : SONY Responsible party : Sony Electronics Inc. Address : 1 Sony Drive, Park Ridge, New Jersey 07656 U.S.A. Telephone number : 201-930-6970 This device complies with Part 15 of the FCC Rules.
-
Page 5: Table Of Contents
Table of Contents Introduction ... 6 Plug and play ... 6 Precautions ... 7 Functions of Controls ... 9 Getting Started ... 11 Installation ... 12 Using Your Display ... 14 Preset and user modes... 14 Using the tilt-swivel ... 15 Damper wire ... -
Page 6: Introduction
Introduction Congratulations on your purchase of a Sony Multimedia CPD-101VS/ 201VS display! This display incorporates over 25 years of Sony experience with Trinitron display technology, ensuring excellent performance and outstanding reliability. This display’s wide scan range (30 – 70 kHz), together with Digital... -
Page 7: Precautions
Precautions Installation • Prevent internal heat build-up by allowing adequate air circulation. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. • Do not install the unit near heat sources such as radiators or air ducts, nor in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. -
Page 8: Warning On Power Connection
Warning on Power Connection • Use the supplied power cord. For the customers in U.S.A. If you do not do this, this display will not conform to mandatory FCC standards. For the customers in UK. If you use the display in the UK, please use the supplied UK cable with the UK plug. -
Page 9: Functions Of Controls
Functions of Controls Front 4 5 6 Microphone Screen Stereo speakers ¤ Mute button ? Reset switch GPE button and indicator . Volume +/– buttons MENU button > +/– Contrast buttons !º U Power switch and indicator 7 8 9 —... - Page 10 Rear !¡ !™ !£ !¢ !¡ AC IN connector !™ 2 Audio plug (green) !£ h MIC plug (red) !¢ ; Video signal cable (blue) !∞ 2 Headphones jack !§ Tilt-Swivel !¶ Subwoofer output jack Functions of Controls Connect the supplied power cord (page 13). Connect to the computer’s audio output (page 12).
-
Page 11: Getting Started
Although this display will sync to other platforms running at horizontal frequencies between 30 and 70 kHz, including Macintosh cable adapter is required. Please consult Sony Technical Support for advice on which adapter is suitable for your needs. -
Page 12: Installation
Installation Step 1: Connect the computer With the computer switched off, connect the video signal cable to the display (VGA) connector on your computer. If your computer supports the DDC plug-and-play standard, this connection will enable DDC communication between the display and the computer. The video signal cable is combined with audio and microphone cables. - Page 13 Step 2: Connect the power cord With the display switched off, connect the power cord to the display and the other end to a power outlet. to a power outlet Power cord (supplied) Step 3: Turn on the display, and then your computer.
-
Page 14: Using Your Display
Using Your Display Preset and user modes The Multimedia CPD-101VS/201VS display has factory preset modes for the 9 most popular industry standards for true “plug and play” capability. For less common modes, its Digital Multiscan Technology will perform all of the complex adjustments necessary to ensure a high quality picture for any timing between 30 and 70 kHz. -
Page 15: Using The Tilt-Swivel
To enter new timings When using a video mode that is not one of the 9 factory preset modes, some fine tuning may be required to optimize the display to your preferences. Simply adjust the display according to the adjustment instructions. -
Page 16: Damper Wire
Damper wire Using a white background, a very thin horizontal line on the screen may be visible as shown below. This line is the damper wire. The Trinitron tube has a vertically striped Aperture Grille inside. The Aperture Grille allows more light to pass through to the screen giving the Trinitron CRT more color and brightness. -
Page 17: Adjustments
Adjustments When one of the preset-type signals is input, no picture adjustment is necessary. You can, however, adjust the picture to your preference by following the procedure described below. To adjust the display, turn on the display and computer. Introducing the On-Screen Display Beyond sound volume and picture contrast adjustment, most adjustments are made using the OSD menu system. - Page 18 Summary of each item MENU COLOR BRIGHT GEOM 1 COLOR Selects the color temperature. 2 CENTER Adjusts the picture centering. 3 SCREEN Reduces the moiré pattern. Adjusts the vertical and horizontal convergence (CPD-201VS only). 4 ZOOM Adjusts the picture size in horizontal and vertical direction proportionally.
-
Page 19: Adjusting The Sound Volume
Adjusting the sound volume Press the . + or – button. The VOLUME/CONTRAST OSD appears. The horizontal and vertical frequencies for each input signal received appear. Horizontal frequency Press the . +/– buttons to adjust volume. + to increase volume –... - Page 20 Select BASS BOOST with the >/. buttons. Press the / button to select ON. To cancel bass boost, press the ? button to select OFF. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. To mute the sound Press the ¤...
-
Page 21: Adjusting The Picture Contrast
Adjusting the picture contrast The adjustment data becomes the common setting for all input signals. Press the > + or – button. The VOLUME/CONTRAST OSD appears. The horizontal and vertical frequencies for each input signal received appear. Press the > +/– buttons to adjust the picture contrast. + for more contrast –... -
Page 22: Adjusting The Picture Centering
Press the ?// buttons to adjust the picture brightness. / for more brightness ? for less brightness To exit the OSD Press the MENU button again. If you don’t touch any buttons the OSD automatically disappears after 30 seconds. Adjusting the picture centering The adjustment data becomes the individual setting for each input signal received. -
Page 23: Adjusting The Picture Size
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Adjusting the picture size The adjustment data becomes the individual setting for each input signal received. To adjust the picture size in horizontal and vertical direction proportionally Select ZOOM in the MENU OSD and press the MENU button. -
Page 24: Adjusting The Geometry
For vertical adjustment Press the >/. buttons. > to increase . to decrease To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Adjusting the geometry The rotation adjustment data becomes the common setting for all input signals. -
Page 25: Selecting The Color Temperature
Press the ?// buttons to adjust. ROTATION / to rotate the picture clockwise PINCUSHION / to bend both sides outward PIN BALANCE / to bend both sides to the right KEYSTONE / to widen the top KEY BALANCE / to move the top to the right To exit the OSD Press the MENU button again. -
Page 26: Adjusting The Convergence (Cpd-201Vs Only)
Select the desired color temperature with the >/. buttons. 11000K for the brightest white 9300K for TV white 6500K for video monitor white 5000K for printing paper white To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Adjusting the convergence (CPD-201VS only) Adjust the convergence to eliminate red or blue shadows that may... -
Page 27: Adjusting The Screen Moiré
Press the ?// buttons to shift the red or blue shadows horizontally or vertically until they disappear. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Adjusting the screen moiré This adjustment is to eliminate wavy or elliptical lines that may appear on the screen. -
Page 28: Activating Screen Degauss
Press the . button to select MOIRE ADJUST. Press the ?// buttons to tune the moiré cancellation effect. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Note on the moiré... -
Page 29: Changing The Osd Position
Select MANUAL DEGAUSS with the >/. buttons. Press the / button to activate the degauss cycle. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Changing the OSD position Select OPTION in the MENU OSD and press the MENU button. -
Page 30: Selecting The Osd Language
Press the ?// buttons to move the OPTION OSD to the desired position. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Selecting the OSD language English, French, German, Spanish and Japanese version of the OSDs are available. -
Page 31: Resetting
Press the ?// buttons to select the desired language. To exit the OSD Press the MENU button again. If you don’t touch any buttons, the OSD automatically disappears after 30 seconds. Resetting To recall the factory settings for an individual adjustment item Select the item you want to reset. -
Page 32: Graphic Picture Enhancement (Gpe)
For inquiries about “IntelliLight” and compatible software, check Sony’s web site (www.ita.sel.sony.com) or call Sony Technical Support (1-888- 4SONYPC). -
Page 33: Selecting The Gpe Mode
MODE 2 Higher contrast and sharpness is applied across the entire screen. MODE 2 is designed to enhance graphic games and movie/video presentations. Note on MODE 2 Whenever the screen resolution is changed, power saving activated, or power turned off, MODE 2 is cancelled and GPE returns to the AUTO mode. -
Page 34: Power Saving Function
Normal Operation mode. Note that the power saving function may not work properly if the video signal contains a “Sync on Green” signal. Mode Power consumption Normal CPD-101VS: 110 W (max) Operation CPD-201VS: 120 W (max) Sleep 15 W (max) Deep Sleep... -
Page 35: Specifications
Specifications Picture tube CPD-101VS: 0.25 mm aperture grille pitch, 15 inches measured diagonally (14.0” viewable), 90-degree deflection, AR coating CPD-201VS: 0.25 mm aperture grille pitch, 17 inches measured diagonally (16.0” viewable), 90-degree deflection, AR coating Viewable image size CPD-101VS: Approx. 285 14.0”... - Page 36 Keystone/Key balance/Bass boost/Manual Degauss/OSD position/OSD language AC input voltage/current CPD-101VS: 100 to 240 V, 50 – 60 Hz, 1.1 – 0.6 A CPD-201VS: 100 to 240 V, 50 – 60 Hz, 1.5 – 0.6 A Power consumption CPD-101VS: Max. 110 W CPD-201VS: Max.
-
Page 37: Troubleshooting
Troubleshooting This section may help you isolate a problem and as a result, eliminate the need to contact technical support, allowing continued productivity. No picture If the U indicator is not lit m Check that the power cord is properly connected. m Check that the U switch is in the “on”... - Page 38 Howling (feedback) is heard m Decrease the volume with . +/– buttons, or turn down the microphone input volume of the sound board. Picture is scrambled m Check your computer manual for the proper display setting. m Check this manual and confirm that the graphic mode and the frequency you are trying to operate is supported.
- Page 39 Picture bounces or has wavy oscillations m Isolate and eliminate any potential sources of electric or magnetic fields. Common causes for this symptom are electric fans, fluorescent lighting, laser printers, etc. m If you have another display close to this display, increase the distance between them to reduce interference.
-
Page 40: Self-Diagnosis Function
While the Auto-degauss cycle is activated, a hum may be heard. The same hum is heard when the display is manually degaussed. This is not a malfunction. • If the problem persists, call your authorized Sony dealer from a location near you, or call Sony Technical Support at 1-888-4SONYPC (1-888-476-6972).