Sony PXW-X400 Upgrade Manual
Hide thumbs
Also See for PXW-X400:
- Instructions before use (99 pages) ,
- Quick manual (59 pages) ,
- Operating instructions manual (159 pages)
Advertisement
Quick Links
Introduction
This document describes the procedure for upgrading the
PXW-X400/X580 to the latest version (V3.02).
First save the upgrade data to an SD card, and then use the
menu to perform the upgrade.
For details on using menus, refer to the operation
manual.
Before Upgrading
Note
If the camcorder is running V1.00 or V1.10, first
upgrade to V2.00 before proceeding further. You can
check the version number using Maintenance >Version
>Number in setup menu. For details about upgrading to
V2.00,refer to the V2.00 version upgrade guide (4-688-
215-11)in the "PXW-X400_X580_Ver-UpGuide(V2.00).
zip"folder.
About the upgrade procedure
The following steps are required in order to upgrade
firmware.
A Upgrade the firmware of the camcorder.
B Upgrade the proxy recording and wireless
LAN connection functions.
About the Required SD Cards
Prepare two SD cards, described in the following table.
Each SD card should only be used in the corresponding
procedure shown.
SD card type
Upgrade SD Card
PROXY SD Card
Notes
• For details about supported SD cards, refer to the
Operation Manual.
• Always use SD cards that are formatted using the
format function of the camcorder.
© 20 17 Sony Corporation
Getting Started
Procedure
A
B
Notes on Performing Upgrade
• For details about obtaining the upgrade files, contact
your Sony dealer.
• Be sure to use the AC adaptor (AC-DN10 or AC-
DN2B) when performing the upgrade. If a battery pack
is attached at the same time, upgrading is still supported
if the AC power supply is interrupted.
• If the Streaming function is enabled, you cannot
upgrade. Please disable the function before start
upgrading procedure. You can check the current
setting below;
– Maintenance >Streaming >Setting
– Maintenance >Network Client Mode >Setting
• Do not do any of the following while performing the
upgrade. Doing so could interrupt the upgrade process,
and cause a malfunction.
– Eject or insert the upgrade SD card
– Turn the power off
• Disconnect connected devices (such as USB wireless
LAN module (IFU-WLM3), SDI, HDMI, microphone,
viewfinder, and lens) and eject any media in the SxS
memory card slots before upgrading.
• Check the operation of the camcorder before using the
camcorder after upgrading.
For details about using the camcorder, refer to the
operation manual.
Checking the Current Version
Display Maintenance >Version >Number in the setup
menu.
PXW-X400 / X580
Advertisement
Related Manuals for Sony PXW-X400
Summary of Contents for Sony PXW-X400
- Page 1 PXW-X400 / X580 Introduction Getting Started This document describes the procedure for upgrading the PXW-X400/X580 to the latest version (V3.02). Notes on Performing Upgrade First save the upgrade data to an SD card, and then use the menu to perform the upgrade.
- Page 2 setup menu, and select [Execute]. Performing the Upgrade A “Please use the AC adapter, Upgrade Version?” confirmation screen appears. A Upgrading the Firmware of the Step 8 Select [Execute]. Camdorder The upgrade begins. There are two phases to the upgrade, “Phase 1” Note →...
- Page 3 on the SD card. B Upgrading the Proxy Recording Next, perform the upgrade. and Wireless LAN Connection Step 6 Attach an AC adaptor to the camcorder, and Functions connect it to an AC power supply. Notes Step 7 Turn the camcorder on to start the camcorder. •...
- Page 4 Note If the problem persists after attempting to resolve the error, contact your Sony dealer. If the upgrade was interrupted If there was an error in the upgrade data, the “Version Upgrade NG: Cannot Read the File. Turn Power Off”...