Page 3
KDC-MP425/MP6026 KDC-W6027/W6027Y DISASSEMBLY FOR REPAIR 3 7 63 1515 0 How to Disassemble (PANEL ASSY) How to install knob (SRC) 1) Remove four screws (A). 1) Place knob (F) and knob (G) in the positions indicated in 2) While holding the section (B) indicated with arrows, pull and the diagram below.
Page 4
KDC-MP425/MP6026 KDC-W6027/W6027Y COMPONENTS DESCRIPTION 3 7 63 1515 0 SWITCH UNIT (X16-2490-10) Ref. No. Application / Function Operation / Condition / Compatibility LCD Driver Drives LCD Remote Control IC Controls the unit REMO ON SW The power supply of IC2 is turned on when base level goes “L”...
Page 5
KDC-MP425/MP6026 KDC-W6027/W6027Y COMPONENTS DESCRIPTION 3 7 63 1515 0 Ref. No. Application / Function Operation / Condition / Compatibility DSI lights when the base is “L”. Q151 DSI Driver DSI turns off when the base is “H”. DSI turns on and off when panel is taken off.
Page 6
KDC-MP425/MP6026 KDC-W6027/W6027Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Pin No. Pin Name Application Processing Operation Description value table R DATA RDS decoder DATA input terminal Not used Destination other than E and E2 L CE CE output terminal for LCD driver...
Page 7
KDC-MP425/MP6026 KDC-W6027/W6027Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Pin No. Pin Name Application Processing Operation Description value table DIMMER Small DET terminal ON : L, OFF : H BVDD BVSS Not used Non Ext AMP CON destination Output “L”...
Page 8
KDC-MP425/MP6026 KDC-W6027/W6027Y MICROCOMPUTER’S TERMINAL DESCRIPTION 3 7 63 1515 0 Truth Pin No. Pin Name Application Processing Operation Description value table LO.S SW Loading start SW DET terminal Loading start : L 12cm DISC EJECT position DET SW terminal 12EJE SW...
KDC-MP425/MP6026 KDC-W6027/W6027Y TEST MODE 3 7 63 1515 0 1. How to enter the test mode 7. CD Receiver Test Mode Specification • While holding the Preset 1 and Preset 3 keys, reset the unit. • When resetting to start, forced ejection of CD is prohib- ited.
Page 10
KDC-MP425/MP6026 KDC-W6027/W6027Y TEST MODE 3 7 63 1515 0 11. Special display when the display is All ON Security Pressing the Preset keys while the power is All OFF dis- • Forced Power ON mode (All models) plays the following information.
Page 11
KDC-MP425/MP6026 KDC-W6027/W6027Y PC BOARD 3 7 63 1515 0 (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) SWITCH UNIT SWITCH UNIT X16-2490-10 (J74-1566-02) X16-2490-10 (J74-1566-02) REMO PANEL 5V L 13942296513 1 100 X16-2490-10 X16-2490-10 Ref. No. Address Ref. No. Address u163 Refer to the schematic diagram for the...
Page 16
KDC-MP425/MP6026 KDC-W6027/W6027Y 3 7 63 1515 0 PC BOARD (COMPONENT SIDE VIEW) CD PLAYER UNIT X32-5500-00 (J74-1552-12) RFOK CP12 CP13 L 13942296513 CP15 MIACK X32-5500-00 Ref. No. Address u163 Refer to the schematic diagram for the values of resistors and capacitors.
Page 17
KDC-MP425/MP6026 KDC-W6027/W6027Y 3 7 63 1515 0 PC BOARD (FOIL SIDE VIEW) CD PLAYER UNIT X32-5500-00 (J74-1552-12) Vref FLAG HOLD MIRR LOCK TRK IN TRK OUT FCS DOWN FCS UP C22 C23 D3.3V DAVdd3.3V SDIO BCKIA 12EJE A.+8V LRCKIA /EJECT...
Page 21
KDC-MP425/MP6026 KDC-W6027/W6027Y 3 7 63 1515 0 (E30-6229) : KDC-MP425 KDC-MPV525 (E30-6278) : KDC-MPV7026 (E30-6277) : KDC-X579 KDC-MPV5025 KDC-MP6026 KDC-WV6027 PRE OUT KDC-W6027/W6027Y ∗ F GND F GND ∗ F GND R365 AUX R R GND AUX GND W101 ∗...
Page 22
KDC-MP425/MP6026 KDC-W6027/W6027Y 3 7 63 1515 0 SWITCH UNIT (X16-2490-10) ED1(SEGMENT) ED1( ESD-GND TP13 FLIP DET RESET RESET VOL A D-GND+ILL-GND L 13942296513 VOL B ILL+B DIMMER REMOTE CONTROL IC TP11 REMO CP2 470 TP10 REMOTE CONTROL TP12 REMO PANEL 5V...