Sony IPELA SNC-EM602R Installation Manual page 2
Network camera
Hide thumbs
Also See for IPELA SNC-EM602R:
- Specification sheet (2 pages) ,
- Instruction manual (2 pages) ,
- User manual (80 pages)
Advertisement
G
ZOOM/FOCUS
switch
Camera block
fixing screws (tilt)
IR LED
Camera block
Camera head
G-1
G-2
IR LED position mark
TOP
mark
IR LED
IR LED position mark
TOP mark
G-3
IR LED position mark
TOP
mark
More
than 60°
IR LED
IR LED position mark
TOP mark
G-4
plate of the camera
G-5
G-6
H
I
12 mm (
More
than 60°
ø20 mm (
more
J
Ceiling
LAN cable
Network
cable
(straight,
not
supplied)
10BASE-
T/100BASE-TX
Router or hub
K
4-M4 hole
Adjusting the position of IR LED
You can adjust all tilt and rotation positions. There is no screw for rotation and
Base(PAN) position.
Turn the camera head to rotate the camera.
You can invert the image by using the setting menu.
1
Loosen the camera block fixing screws.
Loosen the two camera block fixing screws (tilt).
2
Adjust the camera to turn the lens in the desired direction.
3
If the camera is installed on the wall and the tilt angle is more than 60°,
adjust the position of the IR LED depending on the following installation
conditions (-(1), -(2)). If the IR LED is blocked when the lens is
pointed downwards, rotate the camera head 180°, then select the invert
the image function from the setting menu to adjust the top and bottom
position of the image. For other cases, use the camera in the factory
default setting.
Holding both sides of Base(PAN) (arrow ), hold the black metal part
on the camera head and pull up (arrow ) to remove the camera head.
(-1)
Note
If the harness is removed from the connector, connect it to the connector, again.
Turn the camera head clockwise or counterclockwise (90°) to adjust
the position of the IR LED. The adjustment position will depend on the
following installation conditions.
(1) When the camera is pointing to your left
(when you are facing in front of the camera) (-2)
Turn the camera head counterclockwise (90°) to move the mark to "2" on
the plate of the camera.
(2) When the camera is pointing to your right
(when you are facing in front of the camera) (-3)
Turn the camera head clockwise (90°) to move the mark to "3" on the
plate of the camera.
Holding Base(PAN), insert the camera head to the camera block.
Before inserting the camera head, check if the clutches (two positions) on the
camera head are outside of the plates of the camera. (-4)
(1) Slide one side of the camera head downwards (arrow ). (-5)
(2) Pushing the camera head to the opposite direction (arrow ), slide it
downwards (arrow ) and insert into the camera block. (-5)
(3) Tighten the two camera block fixing screws to fix the camera. Check if the
camera head and camera block can be rotated smoothly clockwise and
counterclockwise. (-6)
Note
The mark is positioned to "1" on the plate of the camera at the factory.
4
Slide the ZOOM/FOCUS switch to W/T to adjust the angle of view.
5
Hold down ZOOM/FOCUS switch for a moment to adjust the focus
automatically.
6
Repeat step 1 to 5 until the coverage and the focus are determined.
Notes
ˎ
If you do not follow the steps above to adjust the direction of the IR LED, IR
LED working distance or the image quality may be affected due to the IR LED
being blocked.
ˎ
When you insert the camera head to the camera block, be careful not to shut
the harness between the clutch on the camera head and the plate on the
camera.
ˎ
After you insert the camera head into the camera block, check if the clutches
on the camera head (two positions) are inserted properly in the concave
portion of the camera block.
ˎ
When you adjust the camera head angle without loosening camera block
fixing screw, an internal part may be damaged.
ˎ
If you cannot achieve satisfactory focus by holding down the ZOOM/FOCUS
switch due to the shooting environment, slide the ZOOM/FOCUS switch level
to N/F to focus manually.
ˎ
Do not turn off this unit as soon as the focus is adjusted. Turn off after five
minutes have passed since the focus was adjusted.
ˎ
Poor focus may also be caused by the dome case assembly. Readjust the focus
/
inches) or less
1
2
using the system menu.
For details, refer to the User's Guide of the equipment.
ˎ
When the dome casing is attached it may be visible in the monitor depending
on zoom and rotation. Also, distortion might be observed in images shot
outside the specified optical area.
/
inches) or
13
ˎ
Do not turn the camera block fixing screws (tilt) more than 0.5 to 1 turn, as
16
they may become loose and fall out.
Attaching the Dome Casing
Fix the dome casing and the camera unit.
Align four screw holes on the dome casing with those on the camera unit, and
tighten four screws with the supplied wrench to secure the dome casing.
Note
Make sure the safety cord does not get caught between the dome casing and
camera unit. Rotate the cord and adjust the position of the cord.
Important precautions
Despite the fact that this unit is rated IP66, this section includes important
precautions to prevent any malfunction caused by condensation and/or water
ingress. Read the precautions below thoroughly before installing the unit.
ˎ
Make sure that the cables and/or connectors of the unit that join to the
ones of the installation surface are waterproofed, before you install the unit.
Otherwise, there may be a risk of water entering the unit through these cables.
ˎ
Install the bracket and the camera on an even ceiling or wall, etc. (
ˎ
Install the camera properly, using the supplied screws, while referring to the
Installation Manual. (-2)
ˎ
When feeding the wire rope through one of the wiring slits, fix the wire rope
with the supplied screw to the hole on the bottom of the unit according to
which wiring slit is used. (-3)
ˎ
Use the supplied cable holder (for conduit) or seal the inside of the pipe to
prevent moisture (condensation) entering the pipe. (-4)
ˎ
Use a pipe/joint of ¾ inches-14 NPT or M27 (2.0 mm (
with a thread length of 12 mm or less, and an internal diameter is at least
ø20 mm. Any threaded parts should be waterproofed with a sealant material.
(-5)
ˎ
When connecting flanged pipe to the side conduit hole, seal all around the
flange to prevent water entering. Otherwise water enters the unit through the
gap between the flange and unit. (-6)
ˎ
The bottom of this unit is designed to be waterproof. However, in case b)
in "Preparations" (on the front page), when you use a LAN cable of non-
recommended size to connect to this unit, install this unit in a waterproof
enclosure or on a waterproof ceiling, to prevent water ingress. Alternatively,
seal the bottom hole. (-7) Cover the joint between the ceiling and the unit
with a sealant material to prevent water ingress. (-8)
Install the camera on a wall lengthwise.
ˎ
Position the side conduit hole downward to prevent water ingress from cables.
(-9)
ˎ
In an environment of high temperature and exposed to direct sunlight, install
a SNCA-WP602 Weather protector (not supplied). The Weather protector can
also protect against rain and snow.
Notes on assembly
ˎ
Make sure the safety cord does not get caught between the dome casing and
camera unit. (-10)
ˎ
Before attaching the dome casing to the camera unit, make sure the
waterproof rubber gasket is clean and fits in the groove of the joint surface
properly. (-11)
ˎ
Before attaching the conduit hole cover to the bottom hole, make sure the
waterproof rubber gasket is clean and fits in the groove properly. (-12)
Connection
Connecting to the Network
Connect the LAN port of the camera to a router or hub in the network using a
commercially available network cable (not supplied).
Connecting the Power Source
Power supply equipment pursuant to IEEE802.3af/at (PoE/PoE+* system)
*PoE means Power over Ethernet.
Notes
ˎ
Do not turn off the camera immediately after turning it on. Wait for at least five
ø166 (6
5
/
)
8
minutes before turning off the camera.
ˎ
When power is supplied by IEEE802.3af (PoE) equipment, do not set the
HEATER (EN/EN) switch to EN.
Connecting to the power supply equipment pursuant
to IEEE802.3af/at
The power supply equipment pursuant to IEEE802.3af/at supplies the power
through a commercially available network cable. For details, refer to the
Instruction Manual of the equipment.
Note
Unit: mm (inches)
If you connect the camera to power supply equipment pursuant to IEEE802.3at,
the equipment may limit the power supply and the camera may stop operating.
For details, refer to the instruction manual of the power supply equipment.
Specifications
Compression
Video compression format
JPEG/H.264
Audio compression format
G.711/G.726/AAC
Maximum frame rate
30 fps
Camera
IR LED
20 pcs
IR working distance
30 m (50 IRE)
Signal system
NTSC color system/PAL color system
(switchable)
Image device
SNC-EM602R
1/3type CMOS (Exmor)
Effective picture elements:
Approx. 1,370,000
SNC-EM632R
1/2.9type CMOS (Exmor)
Effective picture elements:
Approx. 2,140,000
Synchronization
Internal synchronization
Horizontal resolution
SNC-EM602R: 600 TV lines (analog video)
SNC-EM632R: 700 TV lines (monitor display ratio
4:3)
Video S/N
More than 50 dB (Auto gain control maximum
rate 0 dB)
Minimum illumination
F1.2/View-DR Off/VE* Off/Auto gain control
maximum rate MAX/50 IRE (IP)/30 fps
SNC-EM602R
Color: 0.05 lx
Black & White: 0 lx (IR ON)
SNC-EM632R
Color: 0.10 lx
Black & White: 0 lx (IR ON)
* VE stands for Visibility Enhancer.
Lens
Focal length
3.0 mm to 9.0 mm
Maximum relative aperture
F1.2 ~ F2.1
View angle
SNC-EM602R: 1280 × 1024 (aspect ratio 5:4)
Vertical: 73.1° to 25.5°
Horizontal: 92.9° to 31.8°
SNC-EM632R: 1920 × 1080 (aspect ratio 16:9)
Vertical: 56.9° to 20.1°
Horizontal: 105.3° to 35.6°
Minimum object distance
300 mm
Interface
LAN port (PoE/PoE+)
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
Others
Power supply
IEEE802.3at compliant (PoE/PoE+ system)
Power consumption
Max. 17W (IEEE802.3at (PoE+), heater enable)
Max. 11W (IEEE802.3af/at (PoE/PoE+), heater
disabled)
Operating temperature
Start temperature:
-30°C to +50°C (-22°F to +122°F) (heater enable)
0°C to 50°C (32°F to 122°F) (heater disable)
Working temperature:
-40°C to +50°C (-40°F to +122°F) (heater enable)
-10°C to +50°C (14°F to 122°F) (heater disable)
Storage temperature
-20°C to +60°C (-4°F to +140°F)
Operating humidity
20% to 90%
Storage humidity
20% to 95%
Dimensions (diameter/height)
166 mm × 128 mm (6
not including the projecting parts
Mass
Approx. 1,580 g (3 lb 7.7 oz), not including the
bracket
Supplied accessories
CD-ROM (supplied programs) (1), Bracket (1),
Template (1), Wire rope (1), Camera unit
mounting screws (4), Screw M4 × 8 (2),
Wrench (1), Installation Manual (this document)
(1 set), Safety Regulations (1 set), Cable holder
(for conduit) (1)
Optional accessory
In-ceiling bracket YT-ICB45*
* Use the fixture position on the bracket.
Weather protector SNCA-WP602
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
-1)
3
/
inches)-pitched)
32
5
/
inches × 5
1
/
inches),
8
8
Advertisement
