Table of Contents
Advertisement
SERVICE MANUAL
Ver 1.1 2003. 07
HCD-SA30 is the amplifier, DVD/SACD and tuner
section in DAV-SA30.
Amplifier section
Stereo mode
44 W + 44 W (6 ohms at
1 kHz, THD 10 %)
Surround mode
Front: 44 W + 44 W
Center*: 44 W
Surround*: 44 W + 44 W
(6 ohms at 1 kHz, THD
10 %)
Subwoofer*: 80 W
(3 ohms at 100 Hz, THD
10 %)
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs
VIDEO 1:
Sensitivity: 150 mV
Impedance: 50 kilohms
VIDEO 2:
Sensitivity: 300 mV
Impedance: 50 kilohms
Outputs
VIDEO 1 (AUDIO
OUT):
Voltage: 1 V
Impedance: 1 kilohm
PHONES:
Accepts stereo
headphones only.
Super Audio CD/DVD system
Laser
Semiconductor
(Super Audio CD/DVD:
= 650 nm)
(CD:
= 780 nm)
Emission duration:
continuous
Signal format system
NTSC or NTSC/PAL
Frequency response (at 2 CH STEREO mode)
DVD (PCM): 2 Hz to
22 kHz (±1.0 dB)
CD: 2 Hz to 20 kHz
(±1.0 dB)
Harmonic distortion
Less than 0.03 %
Sony Corporation
9-877-177-02
2003G16-1
Home Audio Company
© 2003.07
Published by Sony Engineering Corporation
SPECIFICATIONS
Tuner section
System
FM tuner section
Tuning range
North American models: 87.5 – 108.0 MHz
Other models:
Aerial
Aerial terminals
Intermediate frequency
AM tuner section
Tuning range
North American models: 531 – 1,710 kHz (with the
Middle Easten models:
Other models:
Aerial
Intermediate frequency
Video section
Inputs
laser
Outputs
HCD-SA30
Model Name Using Similar Mechanism
Mechanism Type
Optical Pick-up Name
General
PLL quartz-locked digital
Power requirements
synthesizer system
European model:
Australian and Asian models:
Canadian and Mexican models:
(100 kHz step)
87.5 – 108.0 MHz
Saudi Arabian model:
(50 kHz step)
FM wire aerial
75 ohms, unbalanced
10.7 MHz
Voltage selector models: 120 V, 220 V or
interval set at 9 kHz)
Power consumption
530 – 1,710 kHz (with the
Canadian model:
interval set at 10 kHz)
Other models:
531 – 1,602 kHz (with the
Dimensions (approx.)
interval set at 9 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
Mass (approx.)
530 – 1,710 kHz (with the
Operating temperature
interval set at 10 kHz)
Operating humidity
Loop aerial
450 KHz
Design and specifications are subject to change
without notice.
Video: 1 Vp-p 75 ohms
Video: 1 Vp-p 75 ohms
S video:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
P
/C
, P
/C
: 0.7 Vp-p
B
B
R
R
75 ohms
COMPACT AV SYSTEM
AEP Model
UK Model
E Model
Australian Model
NEW
CDM77A-DVBU20
TDP022W
230 V AC, 50/60 Hz
230 – 240 V AC, 50/60 Hz
120 V AC, 60 Hz
120 – 127 V, 220 V or
230 – 240 V AC, 50/60 Hz
Adjustable with voltage
selector
230 – 240 V AC 50/60 Hz
Adjustable with voltage
selector
80 W
90 W
355 75 360 mm
(14 3 14
/
inches) (w/
1
4
h/d) incl. projecting parts
5.9 kg (13 lb 1 oz)
5°Cto 35°C (41°F to 95°F
5 % to 90 %
Advertisement
Table of Contents
Related Manuals for Sony HCD-SA30
Summary of Contents for Sony HCD-SA30
-
Page 1: Specifications
HCD-SA30 SERVICE MANUAL AEP Model UK Model Ver 1.1 2003. 07 E Model Australian Model HCD-SA30 is the amplifier, DVD/SACD and tuner section in DAV-SA30. Model Name Using Similar Mechanism Mechanism Type CDM77A-DVBU20 Optical Pick-up Name TDP022W SPECIFICATIONS Amplifier section... - Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
-
Page 3: Table Of Contents
HCD-SA30 TABLE OF CONTENTS 1. SERVICING NOTE 6. EXPLODED VIEWS ·························································· 4 6-1. Case Section ································································ 82 2. GENERAL 6-2. Front Panel Section ····················································· 83 ·········································································· 7 6-3. Chassis Section ···························································· 84 6-4. DVD Mechanism Section (CDM77A-DVBU20) ········ 86 3. DISASSEMBLY 3-1. -
Page 4: Servicing Note
HCD-SA30 SECTION 1 SERVICING NOTE MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK — BACK PANEL — OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. - Page 5 HCD-SA30 • Service position of UCOM board J-2501-200-A (1mm/11P/L300) J-2501-212-A (1mm/5P/L300) J-2501-167-A (1.25mm/17P/L300) UCOM board...
- Page 6 HCD-SA30 • Service position of DMB03 board UCOM board J-2501-188-A (1mm/15P/L400) J-2501-094-A (1mm/19P/L300) DMB03 board DMB03 board J-2501-188-A (1mm/15P/L400)
-
Page 7: General
HCD-SA30 SECTION 2 GENERAL Front Panel A "/1 (power) (21) I VOLUME control (21, 62) B STANDBY indicator (21) J FUNCTION (21, 52, 54) C Disc tray (21) K PHONES jack (21) D A (open/close) (21) L ./>, PREV/NEXT, PRESET –/+... -
Page 8: Rear Panel
HCD-SA30 Rear Panel AEP, UK models VIDEO OUT VIDEO IN VIDEO IN EURO AV CENTER WOOFER FRONT R FRONT L AUDIO OUT AUDIO IN AUDIO IN OUTPUT(TO TV) COAXIAL VIDEO 1 VIDEO 2 SURR SURR A SPEAKER jacks (12) F EURO AV OUTPUT (TO TV) jacks (17) B VIDEO 1 ANALOG OUT jack (17) G FM 75Ω... - Page 9 HCD-SA30 L ./>, PREV/NEXT, TV CH –/+, Remote PRESET –/+ (23, 51, 54) M H PLAY/SELECT (21, 23, 28, 29, 30) N DVD TOP MENU/ALBUM– (23, 25, 26) O DVD DISPLAY (25, 26, 30, 33, 37, 39, 44, P C/X/x/c/ENTER (23, 25, 26, 28, 30, 32,...
-
Page 10: Case
HCD-SA30 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. CASE DVD MECHANISM HP BOARD, FRONT BOARD UCOM BOARD (CDM77A-DVBU20) DMB03 BOARD TRAY (AU) MS-128 BOARD BASE UNIT PICK-UP UNIT Note: Follow the disassembly procedure in the numerical order given. -
Page 11: Hp Board, Front Board
HCD-SA30 3-2. HP Board, FRONT Board 2 w ire (flat type) 17p (CN801) q; seven screws qa STANDBY board (+BVTP2.6 × 8) qs FRONT board 1 connector (CN881) 4 two claws 6 screw (+PTPWHM2.6 × 6) 7 HP board 8 knob volume assy... -
Page 12: Dmb03 Board
HCD-SA30 3-4. DMB03 Board 1 two screws 3 heat sink (DMB) (+BVTP3 × 8) 2 two screws (+BVTP3 × 12) 5 connector 6 w ire (flat type) (CN102) 13p (CN107) 7 w ire (flat type) 9p (CN106) 4 w ire (flat type) -
Page 13: Tray (Au)
HCD-SA30 3-6. Tray (AU) bottom side 3 two claws 4 tray (AU) 3-7. MS-128 Board 1 belt 3 MS-128 board 2 four claws... -
Page 14: Base Unit
HCD-SA30 3-8. Base Unit 1 belt 7 chuck cam 3 puley 5 two claws 4 gear 2 claw 6 base unit 3-9. Pick-up Unit 6 holder (DVU1) 7 three insulators 1 claw 8 pick-up unit 2 flexible board (CN003) 3 w ire (flat type) -
Page 15: Test Mode
HCD-SA30 Ver 1.1 2003.07 SECTION 4 TEST MODE [GENERAL DESCRIPTION] 0-0. Quit Quit the Syscon Diagnosis and return to the Test Mode Menu. The Test Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions, 0-1. - Page 16 HCD-SA30 0-2. Version 1-0. ALL [10/0] 0-2-2. Revision Press the key on the remote commander, and the servo set The revision number of ROM (IC206) that the program for data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD the DVD system processor (IC207) is stored.
- Page 17 HCD-SA30 11. Wait 500 msec 38. EQ boost adjust 12. Tracking on 39. Auto Loop Filter Offset 13. (TC display start) 40. Auto track gain adjust 14. Wait 1 sec Search Check 15. Jitter display start 41. 32 track jump forward 16.
- Page 18 HCD-SA30 2-1. Disc Type 2-1-3. Disc Type CD It sets up so that it may judge as a disc type of specification of the Disc Type disc with which the set was inserted. : CD disc (normal speed, 12 cm)
- Page 19 HCD-SA30 2-3. Track/Layer Jump 2-5. EEPROM Write Adjust Track/Layer Jump EEPROM Write Adjust FWD R.Lj L0>L1 REV L.Lj L1>L0 1. Focus Offset 3.500Tj Fine FWD U.Fj L0>L1 2. Focus Gain 4.500Tj Fine REV D.Fj L1>L0 3. Trk. Offset Coarse 5.10kTj Dirc 4.
- Page 20 HCD-SA30 2-7. Disc Check Memory MECHA AGING On the Test Mode Menu screen, selecting executes the aging of Disc Check Memory the mechanism deck. 1. SL Disc check 2. SL Disc check ### Aging Test MENU ### 3. SL Disc check Pls use over 40min.
- Page 21 HCD-SA30 • Code list of Emergency History aa: Initialization is completed or not. 10: Communication to RF AMP (IC001) failed. : Complete. 11: Each servo for focus, tracking, and spindle is unlocked. other number : Not complete. 12: Check sum error of EEPROM (IC204).
- Page 22 HCD-SA30 VERSION INFORMATION On the Test Mode Menu screen, selecting displays the ROM version and region code. The parenthesized hexadecimal number in version field is checksum value of ROM. ## Version Information ## IF con. Ver.x. xx SYScon. Ver.x. xx...
- Page 61 HCD-SA30 • Waveforms — RF Board — IC001 r; (FE) IC001 tj (RFAC) IC001 1 (DVDRFP) IC001 el (TE) 0.3 Vp-p 0.5 Vp-p 800m Vp-p 1.3 Vp-p 100m V/DIV, 1 ms/DIV 500m V/DIV, 100 ns/DIV 200m V/DIV, 100 ns/DIV 500m V/DIV, 1 ms/DIV —...
- Page 62 HCD-SA30 — AMP Board — IC450 4 IC300,301,302 2 (OUTL1) 4.6 Vp-p 4.4 Vp-p 1.3 μ s 20.3ns 1 V/DIV, 400 ns/DIV 1 V/DIV, 10 ns/DIV — I/O Board — IC103 wk (YOUTb) IC103 wk (YOUTb) IC103 ea (VOUTb) IC103 ed (COUT)
-
Page 63: Ic Block Diagrams
HCD-SA30 5-35. IC Block Diagrams IC216 SN74ALVCH16841DGGR (DMB03 BOARD) IC257 TC7WH157FK(TE85R) (DMB03 BOARD) 56 1LE 11 7 11 6 SELECT EN G GND 4 LATCH 1D10 1Q10 LATCH 2D10 2Q10 29 2LE IC352 PCM1800E/2K (DMB03 BOARD) 15 14 13 DIGITAL ∑... - Page 64 HCD-SA30 IC509 CXD3068Q (DMB03 BOARD) 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 DVDD2 ASYE DIGITAL ASYMMETRY CORRECTOR DIGITAL DOUT LRCK D/A DIGITAL PCMD INTERFACE DEMODULATOR TES1 TEST1 ERROR...
- Page 65 HCD-SA30 IC808 MSM56V16160F-8TK7R1 (DMB03 BOARD) 35 34 TIMING REGISTER PROGRAMING OUTPUT REGISTER BUFFERS LATENCY INTERNAL INTERNAL COLUMN & COLUMN READ ADDRESS ADDRESS BURST ADDRESS ADDRESS DATA BUFFERS BUFFERS CONTROLLER COUNTOR COUNTOR REGISTER CONTROLLER INPUT DATA SENSE COLUMN REGISTER AMPLIFIER DECODERS...
- Page 66 HCD-SA30 IC103 MM1568 (I/O BOARD) VCC2 VCC1 BIAS 75Ω COUT DRIVER MUTE1 CLAMP GND2 75Ω VOUT DRIVER YC MIX VSAG CLAMP GND2 75Ω YOUT DRIVER BIAS BIAS YSAG GND1 GND1 10 NC 11 GND2 CYIN 12 75Ω CYOUT DRIVER CLP 13...
- Page 67 HCD-SA30 IC903 SI-8120JF (POWER BOARD) OVER CURRENT REGULATOR PROTECTOR LATCH RESET & ON/OFF DRIVER SOFT COMPARATOR START OVER HEAT – PROTECTOR – VREF ERROR AMP IC904 SI-8050S-LF1101 (POWER BOARD) OVER REGULATOR CURRENT PROTECTOR LATCH RESET & DRIVER OVER HEAT –...
- Page 68 HCD-SA30 IC001 CXD1881AR (RF BOARD) 64 63 62 61 60 59 55 54 53 52 FAST ATTACK INPUT OUTPUT HOLD FULL WAVE AGC CHARGE INHIBIT RECTIFER PUMP PROGRAMMABLE FROM S-PORT EQUALIZER INPUT DVDRFP BIAS FILTER DVDRFN DIFFERENTIATOR INPUT INPUT IMPEDANCE...
- Page 69 HCD-SA30 IC502 BA6956AN (UCOM BOARD) CONTROL LOGIC...
-
Page 70: Ic Pin Function Description
HCD-SA30 5-36. IC Pin Function Description • IC207 ZIVA5X-C1F (DVD SYSTEM PROCESSOR)(DMB03 BOARD) Pin No. Pin Name Description VDDP — Power supply terminal (+3.3V) (I/O signal) Address bus HD15 Data bus (address signal multiplexed) HD14 Data bus (address signal multiplexed) - Page 71 HCD-SA30 Pin No. Pin Name Description MRAS SDRAM row address strobe signal output MCAS SDRAM column address strobe signal output SDRAM write enable signal output (“H” : read, “L” : write) GND25 — Ground terminal (SDRAM I/O signal) VDD25 —...
- Page 72 HCD-SA30 Pin No. Pin Name Description MD30 SDRAM data MD31 SDRAM data GND25 — Ground terminal (SDRAM I/O signal) VDD25 — Power supply terminal (+3.3V) (SDRAM I/O signal) VCLK System clock (not used) XCK_I/O_SEL 5.1ch/downmix switch signal output S1 signal output...
- Page 73 HCD-SA30 Pin No. Pin Name Description DATA1(FLR) Audio data(Front L/R signal) output VDDP — Power supply terminal (+3.3V) (I/O signal) GNDP — Ground terminal (I/O signal) DATA2(SLR) Audio data(Rear L/R signal) output DATA3(CSW) Audio data(Center/Subwoofer signal) output IEC958 S/PDIF signal (not used)
- Page 74 HCD-SA30 Pin No. Pin Name Description TCK signal input RESET ZIVA reset input BUS CLK Not used — Ground terminal (inside core) — Power supply terminal (+1.8V) (inside core) Address bus 3 Address bus 2 GNDP — Ground terminal (I/O signal)
- Page 75 HCD-SA30 • IC701 CXD1882R (DVD DECODER)(DMB03 BOARD) Pin No. Pin Name Description 1, 2 D5, D6 Two-way data bus with the mechanism controller — Ground terminal (digital system) Two-way data bus with the mechanism controller Address signal input from the mechanism controller —...
- Page 76 HCD-SA30 Pin No. Pin Name Description XPDI Not used VDDS — Power supply terminal (+5V) (digital system) 59, 60 HA0, HA2 Not used — Ground terminal (digital system) 62, 63 HCS0, HCS1 Not used — Power supply terminal (+3.3V) (digital system)
- Page 77 HCD-SA30 Pin No. Pin Name Description 128, 129 VCCA3, VCCA2 — Power supply terminal (+3.3V) (analog system) Signal output from the charge pump for phase comparator PDHVCC Middle point voltage input terminal for RF PLL Signal output from the charge pump for frequency comparator...
- Page 78 HCD-SA30 • IC901 CXP973064-226R (MECHANISM CONTROLLER)(DMB03 BOARD) Pin No. Pin Name Description NO USE Not used SDEN Serial data enable signal output to DVD/CD RF amplifier DOCTRL/ Digital out on/off control signal output to the digital signal processor ISBTEST “L”: digital out off, “H”: digital out on...
- Page 79 HCD-SA30 Pin No. Pin Name Description CONTROL 2 Disc tray out detection signal input terminal Not used GFS DVD Guard frame sync signal input from the DVD decoder MUTE CD Muting on/off control signal output to the digital signal processor “H”: muting on MUTE 2D Muting on/off control signal output to the motor/coil driver “H”: muting on...
- Page 80 HCD-SA30 • IC501 μPD703260YGF-S01-JBT-A (SYSTEM CONTROLLER)(UCOM BOARD) Pin No. Pin Name Description UNREG MONITOR Monitoring voltage input for protecting power block VDD MONITOR Monitoring voltage input for protecting power block AVREF0 — Analog reference voltage for A/D converter AVSS —...
- Page 81 HCD-SA30 Pin No. Pin Name Description DSP ACK Acknowledge signal output to the DSP (not used) DIR HDIN Data input from the DIR (IC372) DSP ERROR ERROR signal input from the DSP (not used) DSP EXLOCK EXLOCK signal output to the DSP (not used)
-
Page 82: Exploded Views
HCD-SA30 SECTION 6 EXPLODED VIEWS NOTE: • Abbreviation • -XX, -X mean standardized parts, so they may The components identified by mark 0 or AUS : Australian model have some difference from the original one. dotted line with mark 0 are critical for safety. -
Page 83: Front Panel Section
HCD-SA30 6-2. Front Panel Section including S800 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4955-241-1 VOLUME ASSY, KNOB 4-951-620-01 SCREW (2.6X8), +BVTP 4-243-626-01 PLATE, ORNAMENTAL 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING X-4955-257-1 FRONT PANEL ASSY (EXCEPT AEP, UK, RU) -
Page 84: Chassis Section
HCD-SA30 6-3. Chassis Section AEP/ UK / RU model only T101 supplied TU101 supplied supplied supplied supplied 121 122 DVD mechanism section (CDM77A-DVBU20) - Page 85 HCD-SA30 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-243-615-01 LID, CD A-4733-221-A UCOM BOARD, COMPLETE (AUS) 1-775-267-11 WIRE (FLAT TYPE)(29 CORE) A-4747-330-A UCOM BOARD, COMPLETE (KR) 4-951-620-01 SCREW (2.6X8), +BVTP A-4747-390-A UCOM BOARD, COMPLETE (RU)
-
Page 86: Dvd Mechanism Section (Cdm77A-Dvbu20)
HCD-SA30 Ver 1.1 2003.07 6-4. DVD Mechanism Section (CDM77A-DVBU20) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-243-742-01 TRAY (AU) 4-243-743-01 HOLDER (DBU1) 3-080-484-01 DRIVING GRAR 3-053-847-41 INSULATOR 3-080-485-01 PULLEY GEAR 1-689-264-11 PWB, FLEXIBLE (24 CORE) -
Page 87: Electrical Parts List
HCD-SA30 SECTION 7 ELECTRICAL PARTS LIST Note: • COILS • Due to standardization, replacements in the parts When indicating parts by reference number, uH : μ H list may be different from the parts specified in the please include the board name. - Page 88 HCD-SA30 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C403 1-162-927-11 CERAMIC CHIP 100PF C484 1-162-968-11 CERAMIC CHIP 0.0047uF 10% C404 1-162-927-11 CERAMIC CHIP 100PF C485 1-162-968-11 CERAMIC CHIP 0.0047uF 10% C405 1-162-927-11 CERAMIC CHIP 100PF...
- Page 89 HCD-SA30 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D396 8-719-988-61 DIODE 1SS355TE-17 L302 1-456-380-11 INDUCTOR D397 8-719-988-61 DIODE 1SS355TE-17 L303 1-456-380-11 INDUCTOR D401 1-163-001-11 CERAMIC CHIP 220PF L304 1-456-380-11 INDUCTOR < GROUND TERMINAL > L305...
- Page 90 HCD-SA30 COMPONENT DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R403 1-216-843-11 METAL CHIP 1/16W A-4733-215-A DMB03 BOARD, COMPLETE (AUS) ********************** R404 1-218-725-11 METAL CHIP 1/10W A-4733-223-A DMB03 BOARD, COMPLETE (AEP) R405 1-218-725-11 METAL CHIP...
- Page 91 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C264 1-164-947-11 CERAMIC CHIP 0.01uF C502 1-164-943-11 CERAMIC CHIP 0.01uF 10.00% 16V C265 1-117-370-11 CERAMIC CHIP 10uF C503 1-127-772-81 CERAMIC CHIP 33000PF C266 1-164-947-11 CERAMIC CHIP 0.01uF...
- Page 92 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C715 1-164-938-11 CERAMIC CHIP 0.0015uF 10.00% 50V C819 1-164-947-11 CERAMIC CHIP 0.01uF C716 1-125-891-11 CERAMIC CHIP 0.47uF 10.00% 10V C820 1-107-820-11 CERAMIC CHIP 0.1uF C821 1-107-820-11 CERAMIC CHIP 0.1uF...
- Page 93 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C928 1-117-370-11 CERAMIC CHIP 10uF FL908 1-234-177-21 FERRITE C1302 1-125-777-11 CERAMIC CHIP 0.1uF 10.00% 10V < IC > C1304 1-125-777-11 CERAMIC CHIP 0.1uF 10.00% 10V IC203 6-704-069-01 IC MT48LC4M32B2TG-6 <...
- Page 94 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks L416 1-216-296-11 SHORT CHIP R255 1-216-864-11 METAL CHIP 1/16W R257 1-216-829-11 METAL CHIP 4.7K 1/16W L824 1-414-137-31 INDUCTOR 0.22uH R259 1-216-829-11 METAL CHIP 4.7K 1/16W L901...
- Page 95 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R378 1-216-809-11 METAL CHIP 1/16W R555 1-216-864-11 METAL CHIP 1/16W R379 1-216-809-11 METAL CHIP 1/16W R558 1-216-841-11 METAL CHIP 1/16W R380 1-216-809-11 METAL CHIP 1/16W R381...
- Page 96 HCD-SA30 DMB03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R724 1-216-821-11 METAL CHIP 1/16W R809 1-216-864-11 METAL CHIP 1/16W R725 1-216-824-11 METAL CHIP 1.8K 1/16W R810 1-216-864-11 METAL CHIP 1/16W R726 1-216-845-11 METAL CHIP 100K...
- Page 97 HCD-SA30 DMB03 FRONT Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R910 1-216-864-11 METAL CHIP 1/16W R1801 1-162-923-11 CERAMIC CHIP 1/16W R911 1-216-833-11 METAL CHIP 1/16W R1802 1-162-923-11 CERAMIC CHIP 47PF R912 1-216-833-11 METAL CHIP 1/16W...
- Page 98 HCD-SA30 FRONT Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C811 1-126-795-11 ELECT 10uF 20.00% 50V < TRANSISTOR > C813 1-164-360-11 CERAMIC CHIP 0.1uF C814 1-162-964-11 CERAMIC CHIP 0.001uF Q803 8-729-808-42 TRANSISTOR 2SD1624-T-TD Q804 8-729-808-42 TRANSISTOR...
- Page 99 HCD-SA30 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < FERRITE BEAD > < CAPACITOR > FB851 1-500-284-21 FERRITE C101 1-162-964-11 CERAMIC CHIP 0.001uF FB852 1-500-284-21 FERRITE C103 1-128-551-11 ELECT 22uF 20.00% 25V FB881 1-469-144-21 FERRITE...
- Page 100 HCD-SA30 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C191 1-164-156-11 CERAMIC CHIP 0.1uF CN106 1-779-552-21 CONNECTOR, FFC (LIF (NON-ZIF)) 15P C192 1-216-864-11 METAL CHIP 1/16W CN107 1-784-865-01 CONNECTOR, FFC (LIF (NON-ZIF)) 13 C193 1-164-156-11 CERAMIC CHIP 0.1uF...
- Page 101 HCD-SA30 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q144 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R169 1-216-864-11 METAL CHIP 1/16W (AEP, UK, RU) R174 1-216-825-11 METAL CHIP 2.2K 1/16W Q146 8-729-901-00 TRANSISTOR DTC124EKA-T146 R176 1-216-833-11 METAL CHIP 1/16W...
-
Page 102: Ms-128 Board
HCD-SA30 MS-128 POWER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R223 1-216-815-11 METAL CHIP 1/16W A-4731-576-A POWER BOARD, COMPLETE (E, SP, HK, TW, EA) R224 1-218-867-11 METAL CHIP 6.8K 1/10W *********************** R225 1-216-839-11 METAL CHIP... - Page 103 HCD-SA30 POWER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks D918 6-500-522-11 DIODE 10EDB40-TA2B5 A-4728-690-A RF BOARD, COMPLETE D920 8-719-110-03 DIODE MTZJ-T-77-7.5C ****************** < GROUND TERMINAL > < CAPACITOR > EP901 1-537-770-21 TERMINAL BOARD, GROUND C001...
- Page 104 HCD-SA30 SCART STANDBY Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < IC > FB207 1-500-284-21 FERRITE 0uH (AEP, UK, RU) FB208 1-500-284-21 FERRITE 0uH (AEP, UK, RU) IC001 6-703-551-01 IC CXD1881AR < JACK > < COIL >...
- Page 105 HCD-SA30 UCOM Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-4731-578-A UCOM BOARD, COMPLETE (E) < CONNECTOR > ********************** A-4731-588-A UCOM BOARD, COMPLETE (AEP, UK) CN501 1-784-778-11 CONNECTOR, FFC 17P * CN503 1-564-704-11 PIN, CONNECTOR (SMALL TYPE)2P...
- Page 106 HCD-SA30 UCOM Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q515 6-550-363-01 TRANSISTOR 2SB1690KT146 R555 1-216-864-11 METAL CHIP 1/16W Q516 8-729-900-53 TRANSISTOR DTC114EKA-T146 R556 1-216-809-11 METAL CHIP 1/16W Q517 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R558 1-216-809-11 METAL CHIP...
- Page 107 HCD-SA30 UCOM Ref. No. Part No. Description Remarks R634 1-216-833-11 METAL CHIP 1/16W R635 1-216-864-11 METAL CHIP 1/16W R637 1-216-833-11 METAL CHIP 1/16W R638 1-216-845-11 METAL CHIP 100K 1/16W R639 1-216-829-11 METAL CHIP 4.7K 1/16W R640 1-216-833-11 METAL CHIP 1/16W...
- Page 108 HCD-SA30 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003.05...