EX2L-Basil SERVICE MANUAL CHASSIS MODEL MODEL DEST DEST KDL-32W5800 KDL-46W5800 AEP / UK AEP / UK KDL-37W5800 KDL-52W5800 AEP / UK AEP / UK KDL-40W5800 AEP / UK RM-ED020 (UK) RM-ED06 (AEP) - -...
COMPONENTS IDENTIFIED BY SHADING AND MARKED THE EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. - -...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com UK PLUG WARNING WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S.
Page 4
CAUTION 1. MDF-61 Connector (Removal) Slide the slider to release slider Press the centre lock tab to Remove connector lock. release the lock and pull the connector up 2. MDF-61 Connector (Refiitting) Hold the centre of connector Press centre of connector to insert Slide the slider to lock connector - 4 -...
Page 5
3. The harness must not be crossed or twisted 4. Wire Dressing at connector The harness must not bend more than 45 degrees from the direction of the connector base to avoid crossing or twisting. 5. Wire distance at connector The distance between each wire must be wider than 4mm to ensure isola- tion from lamp voltage.
CONNECTORS 2 Pin Connector (SCART) Pin No AV-1 AV-2 Signal Signal Level • • Audio Output B Standard Level: 0.5V rms (Right) Impedance: less than 1KΩ* • • Audio Input B Standard Level: 0.5V rms (Right) Impedance: more than 10KΩ* •...
EX2L SELF DIAGNOSTIC SOFTWARE The identification of errors within the EX2L chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flash- ing LED) and then communicate with each device in turn to establish if a device is faulty.
2-4. Stand Assy Removal 2-5. Under Cover Removal > = > => > Remove the 4 stand fixing screws indicated and lift the TV set To remove the ‘Under Cover’ first remove the ‘Rear Cover’ up and away from the ‘Stand Assy’. (See Sec 2-2-1) and then the ‘Stand Assy’...
2-8. D5N Board Removal (52 inches) 2-9. D6N Board Removal (52 inches) Screws Screws To remove the ‘D5N’ board disconnect all connectors and To remove the ‘D6N’ board disconnect all connectors and then remove the 4 screws circled and ease the board gently then remove the 4 screws circled and ease the board gently away from the back of the TV set.
2-13. HL4A Board Removal 2-12. G5 Board Removal (52 inches) Clip To remove the ‘HL4A’ board first remove the ‘Rear Cover’ (See Sec 2-2-1) the Stand Assy (See Sec 2-2-4) and then the ‘Under Cover’ (See Sec 2-2-5). The ‘Guide, Led’ can then be removed by disconnecting the 1 connector and releasing the 1 clip circled.
2-16. IP2 Board Removal (46 inches) 2-17. TUS Board Removal Screws Screws To remove the ‘IP2’ board disconnect all connectors and then To remove the ‘TUS’ board disconnect the 1 connector and remove the 4 screws circled and ease the board gently away then remove the 2 screws circled and ease the board gently from the back of the TV set.
SECTION 3 SERVICE MENUS 3-1. How to enter the Service Mode 3-3. Writing TVM Data Service adjustments to this model can be performed using the Press “Mute” on the remote commander. The word “SERVICE” supplied Remote Commander (See front cover). changes to “WRITE”...
• : earth - chassis. NOTE: The G2, G4 and G5 boards are not Sony boards so their schematic diagrams and printed wiring boards are not shown in this Service Manual. Schematic diagrams are for reference only. Please refer to the electrical parts list for the correct value and part number of components.
Page 22
BA-EX2L D3.3V Po r t i o n 3 007:2F;007:8H;010:5B X_BOOT_RST RB2009 R2002 1/16W CL2013 CHIP C2002 D3.3V GND_D PLLSYGND Po r t i o n 7 AA19 D1.05V Po r t i o n 1 PLLUMGND AA20 PLSBGND PLSVGND C2007 GND_D 32.768MHz...
TUS-EX2L P l a c e a 4 x 4 a r r a y o f v i a ’ s u n d e r t h e S i l i c o n T u n e r I C f o r g o o d g r o u n d X500 c o n n e c t i o n t o a g r o u n d p l a n e a n d a l s o 27MHz...
~ D6N Printed Wiring Board Side A ~ ~ D6N Printed Wiring Board Side B ~ Text Search J L 6 9 0 8 T 6 9 5 1 F B 6 9 1 1 E Y 6 9 7 4 E Y 6 9 7 5 F B 6 9 1 1 J W 6 9 2 0...
~ IP1 Printed Wiring Board Side A ~ Text Search E T 6 0 0 0 A - 1 6 0 2 - 2 1 1 - A J W 6 2 7 L 6 1 5 1 J W 6 4 6 C N 6 1 5 4 J W 6 4 4 T 6 8 0 0...
Page 50
~ IP1 Printed Wiring Board Side B ~ Text Search J L 6 4 0 2 E T 6 0 0 0 C N 6 1 5 4 J L 6 4 0 7 Q 6 7 0 2 R 6 1 5 3 R 6 1 5 4 R 6 7 0 3 J L 6 4 0 5 I C 6 1 0 1...
~ IP2 Printed Wiring Board Side A ~ Text Search A - 1 6 0 2 - 2 1 2 - A D I M M E R R 6 7 4 6 E T 6 0 0 2 B A C K _ L I G H T _ O N / O F F P H 6 3 0 1 P H 6 1 0 0 I N V _ E R R...
Page 52
~ IP2 Printed Wiring Board Side B ~ Text Search C N 6 1 5 4 D I M M E R B A C K _ L I G H T _ O N / O F F I N V _ E R R E T 6 1 0 1 R 6 1 5 5 J L 6 4 0 7...
SECTION 5 EXPLODED VIEWS NOTE : Non-serviceable items with no part number and no Items marked “*” are not stocked description are not stocked because they are not since they are seldom required for required for routine service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these items.
....................75 Note: To ensure safety and reliability it is Sony policy that power supply boards should not be repaired at component level in the field as a result... The D5N, D6N, G2, G4, G5, IP1 and IP2 boards are regarded as non service items for exchange only and are not indicated in the parts list of this service manual.
Page 58
Note : The components identified by mark contain confidential information. Strictly follow the instructions when ever the components are repaired and/or replaced. REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK A-1743-179-A BA Board, Complete C2015 1-112-777-11 CERAMIC CHIP 0.01UF C2016 1-112-777-11 CERAMIC CHIP 0.01UF <...