DeWalt D26450 Instruction Manual
Random orbit palm sanders
Hide thumbs
Also See for D26450:
- Instruction manual (6 pages) ,
- Instruction manual (7 pages) ,
- User manual
Advertisement
Available languages
Available languages
Quick Links
D
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
E
(AUG04) Form No. 624291-00
D26450, D26451, D26453
The following are trademarks for one or more D
scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box con-
figuration; and the array of lozenge-shaped humps on the surface of the tool.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
1-800-4-DEWALT (1-800-433-9258)
CALL US TOLL FREE AT:
General Safety Instructions
WARNING! Read and understand all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flam-
mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
• Keep bystanders, children, and visitors away while operating a power tool. Distractions
can cause you to lose control.
ELECTRICAL SAFETY
• Grounded tools must be plugged into an outlet properly installed and grounded in
accordance with all codes and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec-
trician if you are in doubt as to whether the outlet is properly grounded. If the tools
should electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user. Applicable only to Class I (grounded) tools.
• Double insulated tools are equipped with a polarized plug (one blade is wider than the
other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in any way. Double insulation
inates the need for the three wire grounded power cord and grounded power supply system.
Applicable only to Class II (double insulated) tools.
• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
• Don't expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of electric shock.
• When operating a power tool outside, use an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor use and reduce the risk of electric shock. When
using an extension cord, be sure to use one heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-
ber, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V
0-25
26-50
240V
0-50
51-100
Ampere Rating
More Not more
Than
Than
0
-
6
18
16
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
A moment of inattention while operating power tools may result in serious personal injury.
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be
caught in moving parts. Air vents often cover moving parts and should also be avoided.
Copyright © 2004 D
WALT power tools: the yellow and black color
E
51-100
101-150
101-200
201-300
AWG
16
14
• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
is left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-
ance enables better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventative safety measures reduce the risk of
starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are dan-
gerous in the hands of untrained users.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tool's operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on
another tool.
SERVICE
• Tool service must be performed only by qualified repair personnel. Service or mainte-
nance performed by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte-
nance instructions may create a risk of electric shock or injury.
Additional Safety Instructions for Sanders
• Accessories must be rated for at least the speed recommended on the tool warning
label. Wheels and other accessories running over rated speed can fly apart and cause injury.
Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.
• Hold tool by insulated gripping surfaces when performing an operation where the cut-
ting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock the operator.
• Always wear eye protection and a respirator when sanding.
• Sanding of lead-based paint is not recommended. See Precautions To Take When
Sanding Paint for additional information before sanding paint.
• Do not operate the unit without the dust collection bag.
• Clean your tool out periodically.
• Empty dust bag frequently, especially when sanding resin coated surfaces such as
polyurethane, varnish, shellac, etc. Dispose of coated dust particles according to the finish
manufacturer's guidelines, or place in a metal can with a tight-fitting metal lid. Remove coated
dust particles from the premises daily. The accumulation of fine sanding dust particles may
self ignite and cause fire.
WALT
E
• Replace worn CFS disc when it causes high tool rpm. High tool rpm caused by a worn
out CFS disc may result in separation of sanding pad from the sander, possibly causing per-
sonal injury. For instructions on replacing the CFS disc, see Tool Care.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
WALT TOOL,
E
tive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and
duration of use, noise from this product may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V ..............volts
Hz ............hertz
min............minutes
..........direct current
..............Class II Construction
elim-
..............safety alert symbol
COMPONENTS (Fig. 1)
A. On/Off switch
B. Speed control dial (D26453)
C. Sanding pad
Motor
Your D
WALT tool is powered by a D
E
the nameplate marking. (Volts, 120 AC only). Voltage decrease of more than 10% will cause loss
of power and overheating. All D
check the power supply.
Model
Sander
D26450
D26451
D26453
Attaching Sanding Discs
Your sander is designed to use 5" (127mm) sanding discs with an 8-hole dust extraction pattern.
Sanding discs for the D26451 and D26453 attach with hook and loop. Sanding discs for the
D26450 attach using pressure sensitive adhesive (PSA).
TO ATTACH PAPER TO THE SANDING PAD (FIG. 2)
CAUTION: Turn off and unplug the tool before making any adjustments or removing
or installing attachments or accessories. Be sure the switch is in the OFF position.
1. Turn the sander over so that the sanding pad is facing upward.
2. Clean the dust from the vinyl pad face.
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, align the holes and place the disc directly on top of the pad.
A................amperes
W ..............watts
............alternating current
n o ..............no load speed
..............earthing terminal
.../min ........revolutions per minute
D. Dust collection bag
E. Vac-adapter
F. CFS disc (Fig. 6)
WALT built motor. Be sure your power supply agrees with
E
WALT tools are factory tested; if this tool does not operate,
E
REQUIRED SANDPAPERS
Disc
Attachment
Hole
Size
Method
Pattern
5"
PSA
8 Holes
5"
Hook & Loop
8 Holes
5"
Hook & Loop
8 Holes
Advertisement
Related Manuals for DeWalt D26450
Summary of Contents for DeWalt D26450
-
Page 1: Additional Safety Instructions For Sanders
Sanding discs for the D26451 and D26453 attach with hook and loop. Sanding discs for the More Not more Than Than D26450 attach using pressure sensitive adhesive (PSA). TO ATTACH PAPER TO THE SANDING PAD (FIG. 2) PERSONAL SAFETY CAUTION: Turn off and unplug the tool before making any adjustments or removing •... - Page 2 FOLLOW ALL SAFETY INSTRUCTIONS IN HEAT GUN INSTRUCTION MANUAL. NOTE (D26450 only): When using PSA sanding discs, remove the disc soon after operation. PSA paper, if the disc is left on during tool storage, sometimes becomes difficult to remove. To aid in the removal of old PSA paper, sand for a few minutes to soften the adhesive backing prior to changing disc.
-
Page 3: Entretien
WALT, COMPOSEZ indiquée sur l’étiquette d’avertissement de l’outil, car les meules et les accessoires SANS FRAIS LE : 1 800 433-9258 (1-800-4-DEWALT). qui sont réglés à une vitesse trop élevée peuvent se briser et occasionner des Règles de sécurité – Généralités blessures lorsque des fragments de métal sont projetés. - Page 5 Parts List for D26451 Type 1 Item Number Part Number Description Qty Required 623832-00 FIELD CASE 624309-00 ARMATURE & BRGS 627401-00 BEARING SUPPORT 624277-00 FIELD 330019-09 SCREW 445860-00 SPRING,BRUSH 445861-03 BRUSH 330019-11 SCREW 330072-98 CORD/8FT/18-2SJ 329301-00 CLAMP,CORD 330019-02 SCREW,PLASTITE 144960-00 SWITCH (ON-OFF) 144983-07 COVER,SWITCH...
- Page 6 Parts List for D26451 Type 1 Item Number Part Number Description Qty Required 649793-00 NAMEPLATE 56194-00 RING,O 624307-00 DUST BAG ASSY 632116-00 BEARING RETAINER 330019-01 SCREW,TORX HD 330003-03 BEARING,BALL 330003-17 BEARING,BALL 151669-00 RING,RETAINING 825209-00 TERMINAL 445964-00 RECEPTACLE 330005-01 PROTECTOR,CORD 603637-00 BRG.