Page 2
IBM E54 Color Monitor Users Guide 6331-07N 6331-97N 6331-47N 6331-67N...
Page 3
References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only IBM's product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any of IBM's intellectual property rights or other legally protectable rights may be used instead of the IBM product, program, or service.
Table of Contents Precautions ............... US-1 Installation ..................US-1 Maintenance ..................US-1 Transportation ..................US-1 Use of the Tilt-Swivel ................US-1 Power Connection Information ............US-1 Identifying Parts and Controls ........ US-2 Unpacking Procedure ..........US-3 Repacking ..............US-3 Setup ................. US-3 Step 1: Install the monitor ..............
US-1 Use of the Tilt-Swivel PRECAUTIONS This monitor can be adjusted within the angles shown Installation below. Do not install the monitor in the following places: Hold the monitor at the bottom with both hands when • on surface (rugs, blankets, etc.) or near materials you turn it horizontally or vertically.
US-2 IDENTIFYING PARTS AND Rear CONTROLS See the pages in parentheses for further detail. Front AC input connector This connector provides AC power to the monitor. g. Video input cable Inputs RGB video signals (0.700 Vp-p, positive) and sync signals. Displays menu &...
US-3 UNPACKING PROCEDURE SETUP À Á This monitor works with platforms running at horizontal frequencies between 30 and 69 kHz. Step 1: Install the monitor • To connect the tilt/swivel base to the monitor, align hooks with the sockets on bottom side of the monitor, and gently push the base towards the front Â...
US-4 Workplace Preparation Step 3: Connect the power cord With the monitor and computer turned off, first Positioning the Monitor connect the proper power cord for your local supply Choose a suitable place to position the monitor where to the monitor, then connect it to a properly grounded it is not near fluorescent desk lighting or any power outlet.
US-5 USING THE ON-SCREEN MENU 1) Menu screen-press the button to display the menu below and exit menus Select mark Press the button to move the selection mark to the desired location. Adjustment icons When the button is pressed. CO NTRAST The selected adjustment screen appears.
US-6 INDIVIDUAL ADJUSTMENT VERTICAL SIZE adjustment Fills the viewable area vertically. CONTRAST adjustment Press the button to make the image smaller, Adjust the screen contrast to match your or press the button to make it larger. Press personal preference. key toggles between VERTICAL SIZE Press the button to decrease contrast and and VERTICAL POSITION.
Page 11
US-7 COLOR selection MANUAL DEGAUSSING The white of the image can be adjusted. After moving the selector to the degauss icon, 1) Use the button to select: (1)9300 press the button. The degaussing action (2)6500 K or (3)User color. takes place a few seconds later. 2) If the (3):the user’s color is selected, “2”...
US-8 TECHNICAL FEATURES TROUBLESHOOTING Preset modes Before contacting technical support, refer to this section. Resolution V. Freq. Mode Problem Check & Adjust (H x V) (Hz) Blank screen · Monitor power switch, 640 x 480 60 (VESA) power cord, signal cable, 640 x 480 75 (VESA) or connector...
US-9 SELF-DIAGNOSIS SPECIFICATIONS FUNCTION S cre e n S ize 1 5 in. visual d iago nal This monitor is equipped with a self-diagnosis Viewa ble scr een size function. You can easily distinguish if the problem is 1 3 .7 5 in. Anti- Glar e, Anti- on the monitor or on the computer by using the Reflective C oating*...
Page 14
US-10 Po we r Input Vo lta ge / 90 to 264 V AC Fre que nc y 50 - 6 0 Hz Curre nt Rating 1. 5 A Po we r 75 W ( MAX. ) Co ns umption Dime ns io n 37 0 x 387 x 3 90 mm (W x H x D)
US-11 SERVICE INFORMATION The following parts are for use by IBM services, or IBM authorized dealers, to support customer warranty. Parts are for service use only. Monitor Information PART NUMBER DESCRIPTION MODEL COLOR 22P7922 E54 Monitor MPR-II, NH 6331 Pearl White...