IBM 8260 Installation Instructions Manual
8260 nways multiprotocol switching hub
Hide thumbs
Also See for 8260:
- Manual (354 pages) ,
- Installation instructions manual (54 pages) ,
- Installation manual (50 pages)
Related Manuals for IBM 8260
Summary of Contents for IBM 8260
-
Page 1: Installation Instructions
Installation Instructions IBM 8260 Nways Multiprotocol Switching Hub Installation Instructions ATM Control Point Version 3.1.9 PNNI Page 1 PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998... -
Page 2: Table Of Contents
..............2.3 Step 3 : Download Inband the 8260 A-CPSW FPGA picocode ... - Page 3 1 step 2 step 3 step 4 step 5 step 8 Download completed June 17 1998 Copyright IBM Corp. 1998 Swap FPGA picocode if necessary Swap microcode step 6 No redundant CPSW, or both A-CPSW microcode are swapped ?
-
Page 4: Prerequisites
1.2 Copying Operational/Boot and FPGA A-CPSW Codes on your workstation 1.2 .1 Code from Distribution Diskettes The present kit contains 2 diskettes : 1 The diskette, Part Number 26L0255, contains for A-CPSW 8260: Ÿ A notice file (READ8260.TXT) Ÿ A-CPSW FPGA picocde (SWPGAB52.ENC) Ÿ... -
Page 5: Code Download From The Web
Installation Instructions Ÿ SA33-0452. IBM 8260 Nways Multiprotocol Switching Hub IBM 8285 Nways ATM Workgroup Switch ATM Control Point Version 3 User's guide. Ÿ SA33-0453. IBM 8260 Nways Multiprotocol Switching Hub IBM 8285 Nways ATM Workgroup Switch 1.2 .1.2 Copying the Distribution Files on your workstation 1 Insert the distribution diskette part number 26L0255 in the workstation. -
Page 6: In-Band Download Method
You can use the local LES of the 8260. 2. You must configure the Ethernet or Token Ring LAN-Emulation Client on your 8260. 3. You must have a TFTP Server somewhere in the IP network (either on the Emulated LAN, either behind an IP Gateway), and the microcode files installed on that TFTP Server. -
Page 7: Out Of Band Download Method
Installation Instructions 4. Check that you can PING the TFTP server from the 8260 LEC. Serial Line IP support (SLIP) mode.Make sure your workstation can act as a TFTP server . 1. Set up a A-CPSW Configuration Console in SLIP Mode: 2. -
Page 8: Step 1: Saving Configuration Before The Upgrade
Installation Instructions Upgrading the 8260 YOU SHOULD MIGRATE YOUR NETWORK CLUSTER BY CLUSTER AND YOU SHOULD DOWNLOAD THE FPGA CODE AND MICROCODE ON ALL YOUR 8260 AND 8285 SWITCHES (in the cluster) BEFORE PERFORMING ANY SWAP COMMAND. Note that interoperability between v.2.x.x clusters and v.3.x.x peer groups is possible through NNI/IISP respectively. -
Page 9: Step 2: Download Inband The 8260 A-Cpsw Operational Microcode
The command "SHOW DEVICE" displays the downloaded operational code level as backup. It should display : v. 3.1.9. 2.3 Step 3 : Download Inband the 8260 A-CPSW FPGA picocode This operation should be done only if your CPSW FPGA level is not uptodate, the latest level is B52. -
Page 10: Step 4: Download Inband The 8260 A-Cpsw Boot Microcode
The command SHOW MODULE <n> VERBOSE (n=9 or 11 depending on A-CPSW active position) displays the FPGA level in backup. It should appear as B52. 2.4 Step 4: Download Inband the 8260 A-CPSW boot microcode Upgrade the new active A-CPSW boot microcode as follows:... -
Page 11: Step 5: Make The Backup A-Cpsw Active
2.6 Step 6: Activate the new A-CPSW microcodes and the new FPGA picocode DO NOT PERFORM ANY SWAP BEFORE HAVING DOWNLOADED : 1 OPERATIONAL CODE PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998 Page 11... -
Page 12: Step 7: Check The New Levels Of Codes
The hub will reset and the backup A-CPSW will become active. Ÿ Perform the step 6 again on the other A-CPSW. PN : 26L0227 EC : F34705 Flash EEPROM version v.3.1.9 June 17 1998 Copyright IBM Corp. 1998 Boot EEPROM Version v.3.1.9 Page 12... - Page 13 EC : F34705 Flash EEPROM version v.3.1.9 MODE SIG TRAF BWITH STATUS INDEX ENABLE 3.1 ANY 85000 Vpi/Vci Port Vpi/Vci Hnb Party 1/50 4.01 2/40 June 17 1998 Copyright IBM Corp. 1998 Boot EEPROM Version v.3.1.9 Role Status Primary Page 13...
-
Page 14: Set Minimum Pnni Phase-1 Parameters
V.3.X.X PEER-GROUPS IS POSSIBLE THROUGH NNI AND IISP LINK RESPECTIVELY. Figure 2, represents a network configured with 8260/8285 at the ATM firmware kit level MES5099. In this example there are two subnetworks (X and Y), three clusters and four hubs, using UNI/SSI/NNI links. You should recognize in this drawing the different components of your current network. - Page 15 Figure 2. Example of a network at the ATM firware kit level(MES 5099). PN : 26L0227 EC : F34705 Cluster 2 (ACN=2) WS 1 vpi3 vpi3 HUB b (HN=2) HUB c (HN=1) Cluster 3 (ACN=3) June 17 1998 Copyright IBM Corp. 1998 WS 2 vpi0 WS 3 HUB d (HN=1) Page 15...
-
Page 16: Example Of A Migration To Pnni Phase 1 (See Figure 3)
Figure 3 represents your network after migration to PNNI phase-1 (v.3.1.0). You can note that Ÿ CLUSTER changes to PEER GROUP Ÿ SSI changes to PNNI Ÿ NNI changes to IISP. PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998 Page 16... - Page 17 Subnetwork Y (ATM address 39.99.99.99.99.99.99.0.0.88.88) Peer Group 3 WS 3 HUB d (HN=1) Figure 3. Example of a network in level PNNI phase 1 (v.3.1.0) Page 17 PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998...
- Page 18 HUBa>set pnni node_0 atm_address: 39.99.99.99.99.99.99.00.00.77.77.01.01.00.00.82.60.01.01.01 o HUBa>SHOW FUTURE_PNNI NODE_0 Check your new ATM address. o HUBa>COMMIT PNNI , the 8260 will be reset The telnet session if any is broken. Login as ADMINISTRATOR on the 8260 console. o HUBa>SHOW PNNI NODE_0 Check your ATM address.
- Page 19 HUBb>set pnni node_0 atm_address: 39.99.99.99.99.99.99.00.00.77.77.01.02.00.00.82.60.01.02.01 o HUBb>SHOW FUTURE_PNNI NODE_0 Check your new ATM address. o HUBb>COMMIT PNNI, the 8260 will be reset The telnet session if any is broken. Login as ADMINISTRATOR on the 8260 console. o HUBb>SHOW PNNI NODE_0 Check your ATM address.
- Page 20 3.1 96 39.99.99.99.99.99.99.00.00.88.88.03 VPI:3 o Check that your reachable address is active (Y) with the command: example for PEER GROUP 1 HUBb (figure3): HUBb>SHOW REACHABLE_ADDRESS 3.1 PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998 Page 20...
- Page 21 HUBc>set pnni node_0 atm_address: 39.99.99.99.99.99.99.00.00.77.77.02.01.00.00.82.60.02.01.01 o HUBc>SHOW FUTURE_PNNI NODE_0 Check your new ATM address. o HUBc>COMMIT PNNI, the 8260 will be reset The telnet session if any is broken. Login as ADMINISTRATOR on the 8260 console. o HUBc>SHOW PNNI NODE_0 Check your ATM address.
- Page 22 PEER GROUP 3 HUBd (figure3): HUBc>SET REACHABLE_ADDRESS 5.1 96 39.99.99.99.99.99.99.00.00.88.88.03 o Check that your reachable address is active (Y) with the command: HUBc>SHOW REACHABLE_ADDRESS 5.1 HUBc>SHOW REACHABLE_ADDRESS 4.1 PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998 Page 22...
- Page 23 HUBd>set pnni node_0 atm_address: 39.99.99.99.99.99.99.00.00.88.88.03.01.D0.E0.20.15.16.17.19 o HUBd>SHOW FUTURE_PNNI NODE_0 Check your new ATM address. o HUBd>COMMIT PNNI, the 8260 will be reset The telnet session if any is broken. Login as ADMINISTRATOR on the 8260 console. o HUBd>SHOW PNNI NODE_0 Check your ATM address.
- Page 24 HUB b, PING a.b.c.d where a.b.c.d is the HUB d ip address --- MIGRATION COMPLETE ---------------------------------------------------- You have successfully completed the MES 5511 upgrade. PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998 Page 24...
-
Page 25: Publication Update
Installation Instructions 2.9 PUBLICATION UPDATE Insert the companion Release Note, Part number 26L0228, EC level F34705 in your publications binder. END OF DOCUMENT Page 25 PN : 26L0227 EC : F34705 June 17 1998 Copyright IBM Corp. 1998...