Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eagle EG6088K
Summary of Contents for Eagle EG6088K
- Page 1 Operation Manual for Shuttle Personnel Carrier...
- Page 2 Thanks for buy our product. For your better use, please read through this manual before operate this vehicle to avoid any possible damage due to improper operation; and keep it in a proper way after reading for future reference. Important Information: Particularly important information is distinguished by the following notations: ▼...
-
Page 3: Table Of Contents
Index 1. Brief Introduction .............................. 1 2. Technical Description............................1 3. Important Labels............................... 1 4. Operation System............................. 3 5. Operational Process ............................5 5.1 Start the vehicle............................5 5.2 Stop the Vehicle ............................5 5.3 Charge the batteries..........................5 6. Rules for Safe Operation..........................6 7. -
Page 4: Brief Introduction
Our electric shuttle personnel carrier is an ideal off-road electric vehicle with excellent performance, fashionable design, luxurious and delicate internal decoration as well as comfortable and safe ride. 2. Technical Description Personnel Carrier Description Vehicle Type EG6088K EG6118KA EG6118KB EG6158K Dimensions(mm) (LxWxH) 4270X1490X2050 4270X1490X2050... - Page 5 Label Content...
-
Page 6: Operation System
4. Operation System 1) Schematic Figure of Operation System 2) Functions of Operating System Power Key —— Control the power supply of the whole vehicle. When the key being inserted into it and turned clockwise, it will switch on lights, horn and the control system; when the key being turned back, the power will be switched off. - Page 7 Voltameter—— Indicate the voltage of battery. On Metric Standard Meter, it ranges from 20V to 60V (for 48V system) and 30V to 96V (for 72V system) from left to right, including 3 sections highlighted by Red, Yellow and Green. Green section represents the battery is full in capacity. With the consumption of the power, the indicator will fall from the right to the left gradually.
-
Page 8: Operational Process
Gearshift —— There is totally 5 positions. Forward shift includes 1, 2, 3 and 4. Reverse shift is R. It is recommended to use 1 for climbing, use 2, 3 and 4 for flat road. 5. Operational Process 5.1 Start the vehicle 1) Switch on the power key;... -
Page 9: Rules For Safe Operation
10) The charger should be packed properly if not used for long time. Below is the charging procedure: ·Turn Off The Power Of The Whole Vehicle 1) When it’s non-onboard charger, one set of batteries, the process is as follows: a) Connect charger to DC receptacle on the vehicle;... -
Page 10: Maintenance
Keep your hands on the steering wheel and your eyes on the path you are going. Always back the vehicle slowly and watch the back carefully. Avoid starting and stopping suddenly. Avoid turning the vehicle too sharply at high speed. Always drive slowly up and down on the slope. - Page 11 cause a short circuit, dangerous spark or may cause damage to the battery or injury to your body. 4) Recharging a. As long as you use the vehicle, regardless of how long you have used it, the battery shall be recharged fully on the same day.
- Page 12 Step by step watering procedure: 1. Open the vent caps and look inside the fill wells. 2. Check electrolyte level; the minimum level is at the top of the plates. 3. If necessary add just enough water to cover the plates at this time. 4.
- Page 13 If any specific gravity readings still register low then follow the steps below. 1. Check voltage level(s). 2. Perform equalization charge. Refer to the Equalizing section for the proper procedure. 3. Take specific gravity readings again. If any specific gravity reading still registers lower than the factory specification of 1.277+/- .007 then one or more of the following conditions may exist: 1.
-
Page 14: Maintenance Of The Gear Box
1.195 6.12 8.16 12.24 24.48 36.72 48.96 1.172 6.05 8.07 12.10 24.20 36.31 48.41 1.148 5.98 7.97 11.96 23.92 35.87 47.83 1.124 5.91 7.88 11.81 23.63 35.44 47.26 1.098 5.83 7.77 11.66 23.32 34.97 46.63 1.073 5.75 7.67 11.51 23.02 34.52 46.03 7) Battery installation... -
Page 15: Maintenance Of The Speed Controller
press spring. Trouble-Shooting for Motor: ▼ ▼ ▼ Only Qualified Electrician Can Change and Adjust The carbon Brush and Commutator. Item Symptoms Possible Causes All copper plates turn black. The pressure of brush is incorrect. The commutator turns black Short circuit in the commutator or armature coil; poor in a certain order and in welding or disconnection between the commutators groups. -
Page 16: Maintenance Of Brake System
·When the vehicle starts, the SRO (protection unit in the controller) will effect. The controller will self-check when the vehicle is running. If any defect inspected, the controller will stop the vehicle to protect the operator and the vehicle. ① Periodical Maintenance: a. -
Page 17: Running-In Of New Vehicle
7.7 Running-in of New Vehicle: In order to guarantee the performance of the vehicle and enhance its reliability and working lift, all parts in motor should experience a certain period of running-in before the motor works with its maximum capacity, thus, each new vehicle is required to give one month of running-in time, detail procedure as per the following: ①... - Page 18 ▼ ▼ ▼ Make sure to turn off the power key and apply the park brake when you do the maintenance unless specified. If the owner is not familiar with the maintenance of this vehicle, the dealer should do the work. 1D –...
-
Page 19: Storage
24. Adjust the toe-in of the front end 25. Clean the body and seat After above maintenance, drive the vehicle to check if the vehicle works properly. 8. Storage Please follow the steps as below when the vehicle is stored. 1. - Page 20 2) Lose control when vehicle starts running: speed cannot be adjusted Malfunction Possible reason Troubleshooting 1.Terminals of Solenoid stick together Check, repair Vehicle runs at full speed when it 2.Controller failure Change just starts 3.Potentiometer failure Repair, change 1. Internal short of Motor Repair, change 2.Motor is assembled too tight or blocked Repair, change...
- Page 21 5.Clearance of tension rod ball is too Change 6. S teering knuckle and master pin is Add Lube not lubricating 7.Steering shaft or its plastic cover Change wear out 1.Rack of redirector wear out Change Redirector 2.Screw plug of Redirector is too tight Adjust 3.Toe-in adjust improperly Adjust...
-
Page 22: Wiring Diagram
1.The clearance of left brake drum shoe and right brake drum shoe is Adjust different 2.Oil on one arrester’s brake shoe Dispose or change Braking deviation 3.tyre pressure is different Repair or Change 4.One wheel cylinder’s piston blocks Adjust 5.Wheel alignment improperly Adjust 6.Brake drum becomes out of round Change... - Page 23 FIG. 1...
- Page 24 FIG.2...