Related Manuals for Toshiba MK2017GAP
Summary of Contents for Toshiba MK2017GAP
- Page 1 TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA MK2017GAP (HDD2158) 2.5-INCH HARD DISK DRIVE USER MANUAL Rev 02 11/2006...
-
Page 2: Table Of Contents
CONTENTS Introduction................1 Setup ..................2 Using the HDD .................4 Troubleshooting...............5 Specifications ................6 Drive Connectors..............8... -
Page 3: Introduction
13ms Average Seek Time • ATA-2,3,4,5 Interface • Supports high transfer rates of 100MB/sec • 2MB Buffer • Rotational speed of 4,200rpm • MTTF 300,000 Hours *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. -
Page 4: Setup
Master/Slave Settings Your Toshiba Hard Disk Drive can be configured as either a "Master" or "Slave" unit. Master configuration is used for all single drive applications, and master or slave configuration (only one of each per port) is used for two drive applications. - Page 5 Installation Notes The drive should be mounted carefully on the surface of 0.1mm or less flatness to avoid excessive distortion. In order to prevent short-circuit under any circumstances, a space of 0.5mm or more should be kept under the PCB. Space should be kept around the drive to avoid any contact with other parts, which may occur due to shock or vibration.
-
Page 6: Using The Hdd
USING THE HARD DISK DRIVE – MK2017GAP (HDD2158) Backing up Data Files To avoid data loss, regularly back up the data files on the hard disk drive. -
Page 7: Troubleshooting
Manager DiskGo by Ontrack. Check with your local computer/software supplier for availability or contact the software manufacturer. How do I install my 2.5" Toshiba Hard Drive into my You will need a HDD mounting kit in order to install a desktop or tower system? Toshiba 2.5"... -
Page 8: Specifications
Seek Time (Average) Internal Transfer Rate 155.4 ~ 286.7Mbits/sec (max) Host Transfer Rate 100Mbytes/sec *Toshiba defines a megabyte (MB) as 1,000,000 bytes and a gigabyte (GB) as 1,000,000,000 bytes. Internal Drive Characteristics Number of Disks Number of Read/Write Heads Track Density (TPI) 44.0K... - Page 9 Physical Height 0.37" (9.5mm) Width 2.75" (69.85mm) Depth 3.94" (100mm) Weight 3.46oz (98g) typ Regulatory The drive satisfies the following standards: Underwriters Laboratories (UL) 1950 Canadian Standard Association (CSA) C22.2 No.220 No. 950 TUV Rheinland EN 60 950 EMC - EN50081-1 EN55022: 1988 Class B EN60555-2: 1987+ A1 EN60555-3: 77A (Co) 38...
-
Page 10: Drive Connectors
DRIVE CONNECTORS – MK2017GAP (HDD2158) Figure 1.MK2017GAP HDD Rear View - Connectors Interface Connector Drive Side Connector Yamaichi GAP050K11617 or equivalent Recommended Host Side Connector Board Straight type: Berg 86455-044 86456-044 or equivalent Cable Berg 89361-044 or equivalent Recommended Cable Characteristics Standard diameter 0.32mm (28AWG) - Page 11 Interface Pin Assignment DRIVE INTERFACE SIGNALS SIGNAL SIGNAL RESET GROUND DD 7 DD 8 DD 6 DD 9 DD 5 DD 10 DD 4 DD 11 DD 3 DD 12 DD 2 DD 13 DD 1 DD 14 DD 0 DD 15 GROUND DMARQ...