SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
ADJUSTMENT INSTRUCTION 1. Application Object 4-3. Adjustment (1) How to adjustment the Component1 These instructions are applied to all of the 32" LCD TV, 1) Select Component1 as the input with Color Bar Pattern LB73A Chassis in 480i 60Hz mode and select ‘Component1’ on screen. 2) After receiving signal for at least 1 second, press the 2.
5-3. Adjustment 6-3. EDID DATA (1) How to adjustment the uPD PAL (1) EDID DATA PORT1 for HDMI 1) Select AV1 as the input with 100% 8 Color Bar Pattern in PAL mode and select ‘AV1’ on screen. 0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 2) After receiving signal for at least 1 second, press the 10 0E 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23 ADJ Key on the Service R/C to enter the ‘Ez - Adjust’...
Page 11
7-4. Adjustment of White Balance 7. Adjustment of White Balance (Passivity Adjustment) 7-1. Required Equipment Operate Zero Calibration of the CA-210. Manual adjustment is also possible by the following sequence. (1) Color analyzer (CA-210 or similar product) (2) Automatic adjustor (with automatic adjustment hour (1) Enter to ‘7.
TROUBLESHOOTING 1. Power Board 1-1. The whole flowchart which it follows in voltage output state Start check Doesn't the Is it identical Is the Interface screen whole come with Power Off signal operated? out? condition? 1. Check the Power Off 2.
Page 13
2. In case of occurring strange screen into specific mode 2-1. In case the OSD does not displayed (1) Symptom 1) LED is white. 2) Some discharge on Panel becomes accomplished continuously. (2) Check following Is the LVDS cable Is the LVDS cable Replace the cable.
Page 14
2-2. In case of does’t display the screen into specific mode (1) Symptom 1) The screen does not become the display from specific input mode. (RF, AV, Component, RGB, DVI) (2) Check following 1) Check the all input mode should become normality display. 2) Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode.(Re-Check using Swap function) Check the NEC64015(IC701) if the main picture is abnormal, and...
Page 15
(5) When Component or RGB-DTV/ PC mode is abnormal Is the CXA2151Q(IC500) Is the Input voltage, IIC Communication Replace the IC. normal? and HV sync normal? Is the MST3362(IC604) Is the Input voltage, IIC Communication Replace the IC. normal? and HV sync normal? Is the Input voltage, IIC Communication Is the Scaler normal? Replace the IC.
Page 16
3. When sound is abnormal (1) Symptom 1) LED is green. 2) Screen display but sound is not output. (2) Check following Is the SPK cable Is the SPK cable Replace SPK cable. normal? connected well? Cable inserts well. Is the Flat cable Cable inserts well.