Page 1 TOSHIBA U S E R ' S M A N U A L M o d e l 4 2 0 0 / 4 3 0 0 S e r i e s...
Page 2 Copyright © 2000 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, with respect to the use of the information contained herein.
Page 3 EU Declaration of Conformity This product carries the CE-Mark in accordance with the related European Directives. CE-Marking is the responsibility of Toshiba Europe, Hammfelddamm 8, 41460 Neuss, Germany. User's Manual...
Page 4 User's Manual...
Page 5 Toshiba DVD-ROM drive SD-C2302** safety instructions **means any letters or numbers. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorised service location.
Page 6 TEAC CD-ROM drive CD-224E safety instructions The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorised service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 7 Toshiba CD-ROM drive XM-1902B safety instructions The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorised service location.
Page 8: General Precautions
General Precautions Toshiba computers are designed to optimise safety, minimise strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 9: Working Environment
EMC (Electromagnetic compatibility) and safety standards. However, Toshiba should not guarantee that this product still observes these EMC standards if options or cables not produced by Toshiba are connected or implemented. In this case the persons who have connected / implemented those options / cables have to assure that the system (PC plus options / cables) still fulfils the required standards.
Page 10 Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference.
Page 11: Table Of Contents
Table of Contents Preface..................xvii Manual contents ..................xvii Conventions ..................xviii Abbreviations ..................xviii Icons....................xviii Keys ....................xviii Key operation..................xix Display ....................xix Messages.................... xix Chapter 1: Introduction ............. 1-1 Equipment checklist................1-1 Features....................1-2 Special features ..................1-7 Utilities....................1-10 Options ....................1-11 Chapter 2: The Grand Tour ............
Page 12 Turning on the power ................3-6 Turning off the power................3-7 Restarting the computer................3-7 Restoring the preinstalled software .............3-8 Restoring the complete system ............3-8 Restoring Toshiba utilities and drivers ..........3-8 Chapter 4: Operating Basics.............4-1 Using AccuPoint™ II ................4-1 AccuPoint™ II precautions ..............4-2 Replacing the cap ................4-2...
Page 13 Soft keys: Fn key combinations............5-3 Emulating keys on enhanced keyboard..........5-3 Hotkeys ....................5-4 Windows special keys................ 5-6 Emulating Fn key on external keyboard ..........5-6 Keypad overlay ..................5-6 Turning on the overlays..............5-6 Temporarily using normal keyboard (overlay on)....... 5-7 Temporarily using overlay (overlay off) ..........
Page 14 Chapter 7: Setup and Password Security........7-1 TSETUP ....................7-1 Executing TSETUP................7-2 Changing values in the TSETUP menu ..........7-3 Accepting changes and exiting SYSTEM SETUP ......7-3 Default configuration................7-3 TSETUP options .................7-4 Memory....................7-4 Password ....................7-4 Battery ....................7-4 Hard Disk Mode ..................7-7 Password security................7-15 How to set the passwords ..............7-16 How to reset the passwords .............7-18 Enabling TSETUP access in user password mode ......7-20...
Page 15 Card Station III..................8-15 Front....................8-16 Right side ..................8-17 Back ....................8-17 Left side.................... 8-19 Spacer....................8-19 Connecting to the Card Station III............ 8-20 Connecting the AC adaptor.............. 8-23 Installing and removing PC Cards ........... 8-24 Port Replicator ..................8-26 Front....................
Page 16 Where to write...................9-25 Appendix A: Specifications............A-1 Appendix B: AC Power Cord and Connectors ....... B-1 Appendix C: The Toshiba International Warranty ....C-1 Appendix D: Keyboard Layouts ..........D-1 Appendix E: Display Controller and Modes ......E-1 Appendix F: If your computer is stolen ........F-1 Appendix G: ASCII Character Codes ........
Page 17: Preface
Preface Congratulations on your purchase of the Satellite Pro 4200 or 4300 Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite Pro 4200 or 4300 Series computer.
Page 18: Conventions
Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, Setup and Password Security, explains how to configure the computer using the TSETUP program.
Page 19: Key Operation
Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign ( + ). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 20 User's Manual...
Page 21: Chapter 1: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by Toshiba. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 22: Features
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses Toshiba’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and...
Page 23 The computer supports high-resolution video Display graphics and employs a AGP bus for superior performance. The screen is a 13.0” DSTN screen with 800 horizontal x 600 vertical pixels or 13.3", 14.1" or 15.0” XGA-TFT with 1024 horizontal x 768 vertical pixels. It can be set at a wide range of viewing angles for maximum comfort and readability.
Page 24 The Satellite Pro 4270 or 4280 Series has an Hard disk drive integrated 6.0 gigabyte* , 2 ½" hard disk drive (HDD) for nonvolatile storage of data and software. The Satellite Pro 4320 Series has an integrated 12 gigabyte*, 2 ½" hard disk drive (HDD) for nonvolatile storage of data and software.
Page 25 A Sound Blaster™ Pro™ and Windows Sound Sound system System (WSS) compatible sound system gives your computer multimedia capability. It incorporates a 64-channel Wave Table Synthesizer and hardware acceleration for advanced sound applications including 3D games, DVD movie playback and Internet communications.
Page 26 This port lets you connect a PS/2 mouse or PS/2™ mouse/ PS/2 keyboard to the computer. keyboard port A PC Card Slot accommodates two 5 mm cards PC card slots (Type II) or one 10.5 mm (Type III) card. These slots support 16-bit PC Cards and CardBus PC Cards (32 bit).
Page 27: Special Features
Special features The following features are either unique to Toshiba computers or are advanced features, which make the computer more convenient to use. Key combinations let you quickly modify the Hotkeys system configuration directly from the keyboard without running a system configuration program.
Page 28 This feature lets you save battery power. If you Battery save mode use Windows 95, you can specify the Power Save Mode in the Power Save Modes window in Power Saver. If you use Windows 98, you can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in Power Saver.
Page 29 To protect from overheating, the CPU has an internal Heat dispersal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. To make one of the three temperature control settings in Windows 95, use the System window of Power Save Modes in Power Saver.
Page 30: Utilities
To start the utility, click the Windows Start button, point to settings and click Control Panel. In the Control Panel, double-click the Toshiba Hardware Setup icon. An easy-to-use menu lets you customize the TSETUP...
Page 31: Options
An additional battery pack can be purchased Battery pack from your Toshiba dealer. Use it as a spare to increase your computer operating time. If you use your computer at more than one site AC adaptor...
Page 32 1-12 Introduction User's Manual...
Page 33: Chapter 2: The Grand Tour
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed This figure shows the computer’s front with its display panel in the closed position.
Page 34: Left Side
Left side This figure shows the computer’s left side. SECURITY LOCK PC CARD SLOT MICROPHONE HEADPHONE JACK JACK POWER POWER BUTTON PC CARD RESET VOLUME CONTROL LOCK LOCK The left side of the computer Press the power button to turn the computer’s Power power on and off.
Page 35: Right Side
Press the reset button to reset the computer when it Reset does not respond to keyboard commands. Use a narrow object such as the tip of a covered ball-point pen. The system restarts, clearing all data in memory and overriding the Resume feature. See Chapter 6, Power and Power-Up Modes, for more...
Page 36: Back Side
A RJ-11 modem jack lets you use a modular Modem jack cable to connect the modem directly to a telephone line. In case of a lighting storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Page 37 Use this port to connect an external PS/2 PS/2 mouse/ compatible mouse or keyboard. The computer keyboard port automatically recognizes which device you have connected when you turn on the power. This infrared port is compatible with Infrared Data Infrared port Association (IrDA) Fast InfraRed (FIR) standards.
Page 38: Underside
Underside This illustration shows the underside of the computer. Make sure the display is closed before turning over your computer. EXPANSION MEMORY SOCKET BATTERY COVER BATTERY LATCH The underside of the computer This cover protects the battery pack, which Battery cover powers the computer when the AC adaptor is not connected.
Page 39: Front With The Display Open
Front with the display open This illustration shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display and lift up. Position the display at a comfortable viewing angle. DISPLAY HINGES DISPLAY SCREEN KEYBOARD INDICATORS...
Page 40: Indicators
A pointer control device located in the centre of AccuPoint™ II the keyboard is used to control the on-screen pointer. Refer to the Using AccuPoint™ II section in Chapter 4, Operating Basics. Control buttons below the keyboard let you select AccuPoint™...
Page 41: System Indicators
System indicators DC IN 15V POWER BATTERY DISKETTE/ BUILT-IN HDD CD-ROM DRIVE The system indicators The DC IN indicator glows green when DC power DC IN 15V is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Page 42: Drives
Drives This section describes the 3 ½" diskette, DVD-ROM and CD-ROM drives. 3 ½" diskette drive DISK-IN-USE INDICATOR DISKETTE SLOT EJECT BUTTON The diskette drive The 3 ½" diskette drive lets you use either double density (720 KB) or high density (1.44 MB) 3 ½"...
Page 43: Region Codes
This drive supports the following formats: DVD-ROM DVD-Video Audio CD CD-EXTRA Photo CD CD-R (read only) ISO 9660 CD-Rewritable (read only) EJECT BUTTON CD-IN-USE INDICATOR EJECT HOLE The DVD-ROM drive Press the eject button to open the drawer partially. Eject button Insert a slender object to open the drawer when Eject hole the power to the computer is off.
Page 44: Cd-Rom Drive
CD-ROM drive EJECT BUTTON CD-IN-USE INDICATOR EJECT HOLE The CD-ROM drive The full-size, maximum 24-speed CD-ROM drive lets you run either 12 cm (4.72") or 8 cm (3.15") compact discs without using an adaptor. The computer is configured with either a CD-ROM drive or a DVD-ROM drive. This drive supports the following formats: Audio CD CD-EXTRA...
Page 45: Ac Adaptor
Power and Power-Up Modes, for details. The AC adaptor Use of the wrong adaptor could damage your computer. Toshiba assumes no liability for any damage in such case. The current ratings are: Satellite Pro 4300 series 60W, 15V DC, 4 Amperes...
Page 46 2-14 The Grand Tour User's Manual...
Page 47: Chapter 3: Getting Started
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Connecting the AC adaptor Opening the display Turning on the power Turning off the power Restarting the computer Restoring the preinstalled software...
Page 48: General Conditions
General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Page 49: Seating And Posture
Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Posture and positioning of the computer Place your chair so that the keyboard is at or slightly below the level of your elbow.
Page 50: Lighting
Lighting Proper lighting can improve legibility of the display and reduce eye strain. Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. Avoid placing the computer in front of bright light that could shine directly in your eyes.
Page 51: Connecting The Ac Adaptor
Chapter 6, Power and Power-Up Modes. Use of the wrong adaptor could damage your computer. Toshiba assumes no liability for any damage in such case. The current rating for the computer is 3.0 amperes. Connect the power cord to the AC adaptor.
Page 52: Opening The Display
Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. Slide the display latch on the front of the computer to the right to unlatch the display panel. Opening the display Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel.
Page 53: Turning Off The Power
Generally, it is a good idea to use the Windows Shut Down menu rather than the power switch to turn off the computer. However, if you are using Windows 95, you can activate the Toshiba Service power off function to ensure a safe shutdown when you press the power switch.
Page 54: Restoring The Preinstalled Software
Restoring Toshiba utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. Use the Tools & Utilities CD-ROM according to instructions in the booklet contained in the CD box to reinstall Toshiba utilities and drivers. 3-8 Getting Started...
Page 55: Chapter 4: Operating Basics
Chapter 4 Operating Basics This chapter gives information on basic operations including using AccuPoint™ II and using the CD-ROM/DVD-ROM drive. It also provides tips on caring for disks and your computer and on heat dispersal. Using AccuPoint™ II To use the AccuPoint™ II, simply push it with your finger tip in the direction you want to move the on-screen pointer.
Page 56: Accupoint™ Ii Precautions
AccuPoint™ II precautions Under certain conditions the on-screen pointer may travel contrary to AccuPoint™ II operation. For example, if You touch the AccuPoint™ II during power-up. You apply constant, soft pressure to the AccuPoint™ II. There is a sudden temperature change. Strong stress is applied to the AccuPoint™...
Page 57: Using Cd-Rom/Dvd-Rom Drives
Using CD-ROM/DVD-ROM drives The full-size drive provides high-performance execution of CD-ROM- based programs. You can run either 12 cm (4.72") or 8 cm (3.15") compact discs without an adaptor. An ATAPI interface controller is used for CD- ROM operation. When the computer is accessing a CD-ROM, an LED on the drive glows.
Page 58 b. Pressing the eject button will not open the drawer when the computer’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 1.5 cm) such as a straightened paper clip into the eject hole just to the right of the eject button. Manual release with the eject hole Grasp the drawer gently and pull until it is fully opened.
Page 59 Lay the CD, label side up, in the drawer. Inserting a CD Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. Press gently at the centre of the CD until you feel it click into place. The CD should lie below the top of the spindle, flush with the spindle base.
Page 60: Removing Compact Discs
Push the centre of the drawer to close it. Press gently until it locks into place. If the CD is not seated properly when the drawer is closed, the CD might be damaged. Also, the drawer might not open fully when you press the eject button.
Page 61: Disk Care
The CD extends slightly over the sides of the drawer so you can grasp it. Hold the CD gently and lift it out. Removing a CD Push the centre of the drawer to close it. Press gently until it locks into place.
Page 62: Diskette Care
Selection using Toshiba utility This utility is used with Windows 95/98 and Windows NT. Click Start, point to Programs, point to TOSHIBA Internal Modem and click Country Selection. The Country Selection icon will appear in the Windows Task Tray.
Page 63 Click the icon with the primary mouse button to display a list of countries that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected country and telephony location. The country list Select a country from the country menu or a telephony location from the submenu.
Page 64 Setting You can enable or disable the following settings: Show flags for country selection. The national flags of supported countries are displayed. AutoRun Mode The country-selecting utility starts automatically when you start up the operating system. Open the Dialling Properties dialog box after selecting country. The dialling properties dialog box will be displayed automatically after you select the country.
Page 65: Video Out
Disconnecting To disconnect the internal modem cable, follow the steps below. Pinch the lever on the connector in the telephone jack and pull out the connector. Disconnect the cable from the computer in the same manner. Video out Use this jack to connect to a television. Be sure to use a video cable. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer.
Page 66: Heat Dispersal
Heat dispersal To protect from overheating, the CPU has an internal temperature sensor that triggers a cooling fan or lowers the CPU operating speed. Use Power Saver Utility or the TSETUP program to select one of three temperature controls. Turns on fan first, then if necessary lowers Maximum performance CPU processing speed.
Page 67: Chapter 5: The Keyboard
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country’s keyboard layout your computer is configured with.
Page 68: F1...F12 Function Keys
F1…F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark grey, but function differently from the other dark grey keys. F1 through F12 are called function keys because they execute programmed functions when pressed.
Page 69: Soft Keys: Fn Key Combinations
Soft keys: Fn key combinations The Fn (function) is unique to Toshiba computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features. Some software may disable or interfere with soft-key operations. Soft-key settings are not restored by the Resume feature.
Page 70: Hotkeys
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off. Enter Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Ctrl Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Press Fn + Alt to simulate the enhanced keyboard’s right Alt key.
Page 71 Battery save mode: Pressing Fn + F2 changes the battery save mode. If you press Fn + F2 in a Windows 95 environment, an icon panel is displayed showing the setting. If you press Fn + F2 in a Windows 98 environment, the Power Scheme menu is displayed.
Page 72: Windows Special Keys
This key has the same function as the secondary mouse button. Emulating Fn key on external keyboard The Fn key is only on Toshiba keyboards. If you use an external keyboard attached to the computer, you can execute Fn key combinations by emulating the Fn key.
Page 73: Temporarily Using Normal Keyboard (Overlay On)
Numeric mode To turn on the Numeric mode, press Fn + F11 (Numeric mode icon lights). Now try numeric data entry using the keys in the following illustration. Press Fn + F11 again to turn off the overlay. & Home PgUp PgDn >...
Page 74: Temporarily Using Overlay (Overlay Off)
Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: Press and hold down Fn. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode icon lights, you can use the overlay for numeric entry.
Page 75: Chapter 6: Power And Power-Up Modes
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
Page 76: Power Indicators
Power on Power off (no operation) Battery charge • Operates AC adaptor is above low • LED: Battery off — connected battery trigger DC IN off point Battery charge • Operates is below low • Alarm sounds battery trigger • LED: Battery flashes —...
Page 77: Dc In Indicator
DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Indicates the AC adaptor is connected and Green supplying proper power to the computer. Indicates a problem with the power supply or Flashing orange overheating of the CPU.
Page 78: Battery Types
Check system. Then press [F1] key. The computer’s RTC battery is a nickel metal hydride (NiMH) battery and should be replaced only by your dealer or by a Toshiba service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 79: Care And Use Of The Battery Pack
Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help assure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
Page 80: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional Toshiba Battery charger to charge the battery pack. Do not attempt to charge the battery pack with any other charger.
Page 81: Monitoring Battery Capacity
Monitoring battery capacity Remaining battery power can be monitored by the Power Saver Utility program. Refer to Utilities in Chapter 1, Introduction. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity.
Page 82: Retaining Data With Power Off
Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: 4 to 7 days Battery pack 1 month or longer RTC battery Extending battery life To maximize the life of your battery pack: If you have extra battery packs, rotate their use.
Page 83 Lay the battery cover upside down. Push the latches to the outside and lift out the battery pack. Removing the battery pack For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your Toshiba dealer. User's Manual Power and Power-Up Modes 6-9...
Page 84: Installing The Battery Pack
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba as replacements. Turn the computer’s power off. Disconnect all cables connected to the computer.
Page 85: Starting The Computer By Password
Slide the battery latch into place to secure the battery pack. Securing the battery cover Starting the computer by password If you registered a password as supervisor or user, you must enter it to start the computer. If you forget your password, use the password service diskette.
Page 86: Power-Up Modes
If you enter the password incorrectly, a buzzer sounds. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. The following steps describe how to use a service password diskette to start the computer if you’ve forgotten the supervisor’s or user’s password.
Page 87: Hotkeys
Hotkeys You can use hotkeys Fn + F3 to set the power-up modes. See Chapter 5, Keyboard, for details. TSETUP You can use the MS-DOS-based utility TSETUP to set two power-up modes: Resume and Boot. See Chapter 7, Setup and Password Security, for details.
Page 88: Ring Indicator Power On
Ring indicator power on This feature lets the computer’s power be turned on automatically when a call comes in from a remote modem. When a modem receives a signal from a remote modem, it sends a ring indicator power on call to the computer. This feature does not work with a PC Card under Windows 95.
Page 89: Chapter 7: Setup And Password Security
Chapter 7 Setup and Password Security This chapter explains how to use TSETUP to configure your computer and how to set security passwords. When you configure the computer, the computer stores your selected values in memory that is backed up by the internal Real Time Clock (RTC) battery.
Page 90: Executing Tsetup
Executing TSETUP Select Restart (the computer) in MS-DOS mode? from the Shut Down window. After the computer reboots in MS-DOS, type TSETUP and press Enter. TSETUP displays the SYSTEM SETUP screen. The TSETUP screen is divided into two pages SYSTEM SETUP (1/2) and SYSTEM SETUP (2/2).
Page 91: Changing Values In The Tsetup Menu
Changing values in the TSETUP menu Press to move between the two columns. Press move between items in a column. Press either the space bar or BkSp to change the value. Press PgUp or PgDn to change pages. On either page, you can go directly to a specific group by pressing the first letter (highlighted) of the group’s name.
Page 92: Tsetup Options
This section describes each group and its options. Most functions described in this section can also be changed using Toshiba’s Hardware Setup or Power Saver Utility in Windows. The I/O port, IRQ and DMA channel are set in Windows 95/98 Device Manager.
Page 93 The following shows full power settings. (Default) Full power BATTERY SAVE OPTIONS Processing Speed = High CPU Sleep Mode = Enabled Display Auto Off = 30Min. HDD Auto Off = 30Min. System Auto Off = Disabled (Resume mode only) LCD Brightness = Super-Bright or Bright* Cooling Method = Performance...
Page 94: Pointing Devices
Peripheral This group of options determines how a number of internal and external devices work with your computer. Pointing Devices Use this option to enable or disable the AccuPoint II when a PS/2 mouse is connected to the computer. This tab lets you select Auto-Selected and Simultaneous. If a PS/2 mouse is connected to the computer Auto-Selected when you turn on the power, the PS/2 mouse is...
Page 95: Hard Disk Mode
USB Legacy Emulation Use this option to enable or disable USB Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB Legacy Emulation item in TSETUP to Enabled. = Disabled (Default) USB Legacy Emulation = Enabled...
Page 96: Boot Priority
Boot priority This tab sets the priority for booting the computer. Select from the following settings: The computer looks for bootable files first on the diskette drive, then on the HDD and last on the CD-ROM CD/DVD-ROM. (Default) The computer looks for bootable files first on the HDD, then on the diskette drive and last on the CD-ROM CD/DVD-ROM.
Page 97: Lcd Display Stretch
Power On Display Lets you set the display to be used when the computer is booted. Selects an external monitor if one is connected. Auto-Selected Otherwise, it selects the internal LCD. (Default) Selects both the internal LCD and external Simultaneous monitor for simultaneous display.
Page 98 Power-up Mode This option lets you choose between Resume and boot mode. These settings are for the MS-DOS environment only. When you use Windows, settings made in Power Saver will be used. CPU Cache, Level 2 Cache Use this feature to enable or disable the CPU cache and to set the write policy.
Page 99 Auto Power On This option lets you set a time for automatic power on and lets you enable or disable the ring indicator feature. Ring Indicator is displayed only when the computer is in Resume mode. OPTIONS Alarm Time 00:00:00 Alarm Date Option Disabled Ring indicator...
Page 100 Panel Power On/Off This option allows you to automatically turn your computer on or off by opening or closing the display panel. Second page of TSETUP Configuration This option allows you to set the configuration method. I/O Ports This option lets you specify the settings for the serial and parallel ports and built-in modem.
Page 101 Built-in Modem This option allows you to set the COM level for the built-in modem port. If a built-in modem (not available in some markets) is not installed, this selection is not active. The built-in modem port interrupt request level (IRQ) and I/O port base address for each COM level is shown below.
Page 102: Pci Bus
When the Parallel Port Mode (see settings below) is set to ECP, the DMA channel can also be set to 1 or 3. The default is 3. LPT setting I/O address Interrupt level DMA Channel 3 (Default) LPT 1 378H LPT 2 278H LPT 3...
Page 103: Password Security
Drives I/O This item displays the installed hard disk drives and CD/DVD-ROM drives: HDD, CD-ROM. It appears only in TSETUP. Settings for Hard Disk Drive = Primary IDE (1F0H/IRQ14) (HDD ready for use) Settings for CD/DVD-ROM drive = Secondary IDE (170H/IRQ15) CD-ROM (CD/DVD-ROM ready for use) Floppy disk I/O...
Page 104: How To Set The Passwords
Supervisor password logon The following restrictions apply to the user when you log on with a supervisor password: User password will not provide access to the Instant security computer. User password will not provide access to the Resume Mode computer. The supervisor password will provide access to the computer from instant security or Resume mode even if the user password was used to log on to the computer.
Page 105: User Password
a.) If character strings match, the password is registered and the display changes to: SUPERVISOR PASSWORD = Registered USER PASSWORD MODE = Unable to run SETUP Do you want to change the setting <Y/N>? If you do not want to provide user access to the TSETUP program, press N to return to the DOS prompt.
Page 106: How To Reset The Passwords
How to reset the passwords This section describes how to reset the supervisor and user password. Supervisor password Go to the DOS prompt, type in SVPW, and press Enter. If the password has been registered, the following line will be displayed: SUPERVISOR PASSWORD = Registered Do you want to delete the supervisor password <Y/N>?
Page 107 User password To delete a user password, execute TSETUP, then: Press the Space or BkSp key to display the following prompt: Password = Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Password = **** If you press Enter before entering the password, Registered will appear on the display.
Page 108: Enabling Tsetup Access In User Password Mode
Enabling TSETUP access in user password mode There are two ways to display the menu letting you provide access to TSETUP and other restrictions imposed by the supervisor password. When you register a supervisor password and when you enter the command SVPW/U at the DOS prompt.
Page 109 Type in the password and press Enter. The following menu appears: 1. Able to run SETUP 2. Unable to run SETUP 3. Unable to show Processor Serial Number item. Select number <1/2/3>? If you select 1, TSETUP access is enabled (and other restrictions disabled).
Page 110: Making A Password Service Diskette
Making a password service diskette If you forget the password, the password service diskette lets you bypass the password function. To make a password service diskette, you will need one 3 ½” 2DD or 2HD diskette that contains no data you want to keep. You cannot make a password service diskette for the supervisor password.
Page 111 When a password service disk is made, the computer overwrites all the data on the diskette with password data. Make sure the diskette you insert does not contain any data you want to keep. If your computer is protected by the Power on Password, when you turn the power on the following message appears: password = If the computer boots by the Auto Power On function and Resume is on,...
Page 112 7-24 Setup and Password Security User's Manual...
Page 113: Chapter 8: Optional Devices
The computer is equipped with a PC Card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC Card that meets industry standards (manufactured by Toshiba or other vendor) can be installed. The slots support 16-bit PC Cards, including PC Card 16’s multifunction card and CardBus PC Cards.
Page 114: Installing A Pc Card
Installing a PC Card Two PC Card connectors are located one above the other on the left side of the computer. Both connectors are accessed from the same slot. You can install two Type II cards, one in each connector, or one Type III card in the bottom connector.
Page 115 Slide the PC Card lock into the locked position. If you connect a security cable to the computer, the PC Card lock will be blocked, preventing removal or installation of a PC Card. To remove or install a PC Card, first remove the security cable. Securing the PC Card lock After installing the card, refer to the card’s documentation and check the configuration to make sure it is appropriate for your card.
Page 116: Removing A Pc Card
Removing a PC Card Before you remove a PC Card, refer to the card’s documentation for procedures and use Windows PC Card Properties utility to deselect the card. To access the PC Card Properties utility click Start, point to Settings, click Control Panel and double click the PC Card Properties icon.
Page 117: Installing Memory Module
Installing memory module Follow the steps below to install a memory module. Set the computer to boot mode and turn off the power. Do not try to install a memory module with the computer turned on. You can damage the computer and the device. Remove all cables connected to the computer.
Page 118: Removing Memory Module
Push the module down so it lies flat. Latches on either side will click into place to secure the module. Installing a module Seat the cover and secure it with two screws. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes.
Page 119: Clearing Hibernation Files
Grasp the module and pull it out. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Removing the memory module Seat the cover and secure it with two screws and replace the battery. Clear Hibernation files.
Page 120: Additional Battery Pack
Additional battery pack You can increase the portability of the computer with additional battery packs (PA2487U). If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.
Page 121: Front
Front The following illustration shows the Card Station IV’s front. COMPUTER CONNECTOR ENGAGING PIN (NOT SHOWN) METAL LATCHES ENGAGING PIN (NOT SHOWN) FINGER GRIP EJECT LEVER GUIDE RAILS FINGER GRIP The front This is the computer interface. It connects directly Computer connector to the computer’s docking interface port.
Page 122: Back
Back The following illustration shows the Card Station IV’s back. SERIAL PORT PARALLEL PORT LINE-OUT JACK LINE-IN JACK MICROPHONE JACK DC IN COMPUTER LOCK PS/2 MOUSE PORT EXTERNAL MONITOR PORT SECURITY LOCK SLOT PS/2 KEYBOARD PORT PC CARD SLOT USB PORTS The back The AC adaptor connects to this socket.
Page 123: Left Side
A standard 3.5 mm mini microphone jack enables Microphone jack connection of microphone for audio input. When you connect a microphone, the internal microphone is automatically disabled. A standard 3.5 mm mini line-in jack enables Line-in jack connection of a stereo device for audio input. A standard 3.5 mm mini line-out jack enables Line-out jack connection of a stereo device for audio output.
Page 124: Ac Adaptor
The AC adaptor Use of the wrong adaptor could damage your computer. Toshiba assumes no liability for any damage in such case. The current rating for the computer is 3.0 amperes.
Page 125: Connecting To The Card Station Iv
Connecting to the Card Station IV The Card Station IV is designed to assure a secure connection by a few simple operations. Before connecting, make sure the engaging pins are down. Before connecting, remove the rubber cover from the computer’s Docking Interface cover.
Page 126: Connecting The Ac Adaptor
Connecting the AC adaptor To supply AC power to the computer, connect the AC adaptor as shown below. Connecting the AC adaptor Disconnecting the Card Station IV To disconnect the Card Station IV, follow the steps below. Shut down the computer. Make sure the computer lock is pushed back to enable disconnection of the computer from the Card Station IV.
Page 127: Card Station Iii
Card Station III In addition to the ports available on the computer, a Card Station III (PA2717UY) provides MIDI/joystick ports, two PC Card Slots that can be used in addition to the slots on the computer and separate ports for PS/2 mouse and PS/2 keyboard.
Page 128: Front
Front The illustration below shows the Card Station III’s front. COMPUTER ENGAGING PIN CONNECTOR ENGAGING PIN CONNECTION METAL LATCHES LOCK VOLUME CONTROL FINGER GRIP PC CARD SLOT (2) GUIDE RAILS EJECT LEVER FINGER GRIP The front This is the computer interface. It connects directly Computer connector to the computer’s docking interface port.
Page 129: Right Side
Right side Refer to the previous illustration for the location of items on the Card Station III’s right side. This lever pops out for easy disconnection of the Eject lever computer from the Card Station III. A PC Card Slot accommodates a 5 mm (Type II) PC Card Slot or a 10.5 mm (type III) card.
Page 130 Use this Centronics-compatible, 25-pin parallel Parallel port port to connect a parallel printer or other parallel device. It replaces the computer’s parallel port. External monitor port This 15-pin port lets you connect an external video monitor. Note that the Resume feature is effective with an external monitor.
Page 131: Left Side
Left side Refer to the previous illustration for the location of items on the Card Station III’s left side. A PC Card Slot accommodates a 5 mm (Type II) PC Card Slot or a 10.5 mm (type III) card. This slot supports CardBus.
Page 132: Connecting To The Card Station Iii
Connecting to the Card Station III Connection of the Card Station III requires a spacer. You can connect the spacer by itself to either the Card Station III or to the computer. You can also either prevent or enable disconnection of the computer from the spacer while the spacer remains connected to the Card Station III.
Page 133 Disconnecting the computer without the spacer To disconnect the spacer alone or spacer with computer from the Card Station III, follow the steps below. Shut down the computer or for hot undock click Start then click Eject. Place one hand on the front of the computer and the other hand on the back.
Page 134 Connecting the spacer to the Card Station III This section describes connection of the spacer to the Card Station III. Make sure the engaging pins on the Card Station III are down (pull the release lever forward). Seat the spacer between the guide rails on the Card Station III. Connecting the spacer Hold the Card Station III and spacer together on each side and slide the spacer forward with your thumbs.
Page 135: Connecting The Ac Adaptor
Seat the computer between the spacer guide rails and push the computer forward to secure the connection with the Card Station III. Connecting the computer Connecting the AC adaptor To supply AC power to the computer, connect the AC adaptor as shown below.
Page 136: Installing And Removing Pc Cards
Installing and removing PC Cards The Card Station III has two PC Card Slots, one on either side, that each accommodate one Type II or one Type III card. To install a PC Card, follow the steps below. Turn off the computer if it is connected. A pair of flaps protects the PC Card Slot.
Page 137 To remove a PC Card, follow the steps below. Make sure the computer is in boot mode, then turn off the power. If the computer is not attached, do not remove the card unless the computer was in Boot mode the last time you turned it off when it was attached to the Card Station III.
Page 138: Port Replicator
Port Replicator In addition to the ports available on the computer, a Port Replicator (PA2731UE) provides audio line-in and line-out jacks, MIDI/joystick ports and separate ports for PS/2 mouse and PS/2 keyboard. The Port Replicator connects directly to the docking interface port on the back of the computer so no cabling is necessary.
Page 139: Front
Front The illustration below shows the Port Replicator’s front. ENGAGING PIN COMPUTER (NOT SHOWN) CONNECTOR METAL LATCHES ENGAGING PIN (NOT SHOWN) VOLUME CONTROL FINGER GRIP EJECT LEVER GUIDE RAILS FINGER GRIP EJECT LEVER RELEASE BUTTON The front This is the computer interface. It connects directly Computer connector to the computer’s docking interface port.
Page 140: Right Side
Right side Refer to the previous illustration for the location of items on the Port Replicator’s right side. This lever pops out for easy disconnection of the Eject lever computer from the Port Replicator Use this dial to adjust the headphone volume. Volume control Back The illustration below shows the Port Replicator’s back.
Page 141: Left Side
Two Universal Serial Buses (USB) enable daisy- Universal Serial chain connection of a number of USB-equipped Buses devices to one USB. A standard 3.5 mm mini headphone jack enables Headphone jack connection of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speaker is automatically disabled.
Page 142: Connecting The Port Replicator
Connecting the Port Replicator The Port Replicator is designed to assure a secure connection by a few simple operations. To connect the Port Replicator, follow the steps below. Remove the rubber cover from the Docking Interface port. Make sure the engaging pins on the Port Replicator are down. Seat the computer between the Port Replicator’s guide rails.
Page 143: Connecting The Ac Adaptor
Connecting the AC adaptor To supply AC power to the computer, connect the AC adaptor as shown below. Connecting the AC adaptor Disconnecting the Port Replicator To disconnect the Port Replicator, follow the steps below. Shut down the computer. Make sure the computer lock is pushed back to enable disconnection of the computer from the Port Replicator.
Page 144: Parallel Printer
Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly.
Page 145: External Monitor
External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. The Resume feature can be used with an external monitor. Simply enable Resume and the computer will maintain the data as it is displayed on the external monitor.
Page 146: Ps/2 Mouse
PS/2 mouse Use the PS/2 mouse/keyboard port on the computer. Make sure the mouse has a cable with a 6-pin connector for the PS/2 mouse port. If the mouse’s cable is not compatible, see your dealer for an adaptor cable. How the computer treats the connection to a PS/2 mouse depends on the setting for Pointing Devices under the Others options in the Setup program.
Page 147: Security Lock
Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.
Page 148 8-36 Optional Devices User's Manual...
Page 149: Chapter 9: Troubleshooting
Chapter 9 Troubleshooting Toshiba designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 150: Analysing The Problem
Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your diskette, CD-ROM or DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer.
Page 151: Hardware And System Checklist
If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the Toshiba logo. Random characters appear on the screen, and the system does not function normally.
Page 152: Power
Power When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply, Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems.
Page 153 Battery If you suspect a problem with the battery, check the DC IN indicator as well as the indicators for the battery. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t The battery may be discharged.
Page 154: Password
Password If you forgot your password, you can use your password service diskette to start the computer. If you did not make a password service diskette or if it doesn't work, see your dealer. Problem Procedure Cannot enter Refer to the Password security section in password Chapter 7, Setup and Password...
Page 155: Lcd Panel
LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup and Password Security, for more information. Problem Procedure Lines appear broken Check if you are in DOS mode. In DOS, lines may appear broken, because of the LCD screen’s higher resolution.
Page 156: Cd-Rom Drive
CD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive's drawer is securely closed. CD in the drive Press gently until it clicks into place. Open the drawer and make sure the CD is properly seated.
Page 157: Dvd-Rom Drive
DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s drawer is securely closed. DVD in the drive Press gently until it clicks into place. Open the drawer and make sure the DVD is properly seated.
Page 158: Diskette Drive
Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Some programs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware configuration match’s your software’s needs. You cannot access the Try another disk.
Page 159: Printer
Printer Refer also to the Parallel printer sections in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not Check that the printer is connected to an electric turn on outlet.
Page 160: Serial Mouse
PS/2 mouse Problem Procedure On-screen pointer Check that the PS/2 mouse cable’s 6-pin does not respond to connector is firmly connected to the PS/2 mouse operation mouse/keyboard port. You may have connected the mouse after turning the computer on. Turn off the computer, make sure the mouse is firmly connected and turn the computer back on.
Page 161: Pc Card
PC Card Refer also to Chapter 8, Optional Devices. Problem Procedure PC Card error occurs Reseat the PC Card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer.
Page 162: Sound System
Sound system Refer also to Chapter 7, Setup and Password Security. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows 95/98 Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict...
Page 163: Hibernation
Hibernation Problem Procedure Hibernation does Are you using a compression utility on C drive? not work Hibernation will not work with Windows 95 Drvspace or other compression utility. Hibernation will not work if the Windows 98 Drive Converter converts the file allocation table to FAT32.
Page 164: Memory Expansion
Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure The following Make sure the memory module installed in the message is displayed: expansion slot is compatible with the computer. If an incompatible module has been installed, Please remove follow the steps below.
Page 165: Diagnostic Test
Go to drive C and at the DOS prompt C:\>, type TDIAGS. MS-DOS loads the diagnostic test and displays the following screen: TOSHIBA personal computer xxxx DIAGNOSTICS version x.xx (c) copyright TOSHIBA Corp. 19xx Test the DIAGNOSTICS (Y/N) To execute the program type Y; to exit, type N.
Page 166: Choosing Test Options
Choosing test options Before the test begins, you are prompted to select whether to test the following components. To select the test, type Y at the prompt, otherwise type N. Component Prompt Diskette drive Test the FDD (Y/N)? This test writes patterns to the diskette. Use a formatted, write-enabled diskette.
Page 167: Test Sequence
Test sequence The diagnostic test checks the computer and attached peripherals in the following sequence: System test Memory test Display tests Floppy Disk (Diskette) test Hard disk test Printer test When a test is in progress, the program displays: IN PROGRESS TTSSDSS where TT indicates the test number, the first SS indicates the subtest number, D indicates the drive (if tested), and the second SS indicates the hardware status.
Page 168: Character Attributes
Display tests Character attributes After the System/Memory tests end, the Display tests begin with the Character attributes screen shown below. CHARACTER ATTRIBUTES NEXT LINE SHOWS NORMAL DISPLAY. NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN NEXT LINE SHOWS INTENSIFIED DISPLAY. NEXT LINE SHOWS REVERSE DISPLAY. RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR NEXT LINE SHOWS BLINKING DISPLAY. BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB PRESS [ENTER] KEY Make sure the line under the message NEXT LINE SHOWS BLINKING...
Page 169: Character Sets
Character sets There are two character set tests. The first checks that the screen can display characters in a 40-column by 25-row format (the characters are wider than normal). The display screen appears as: If the display screen matches the figure above, start the second character set test by pressing Enter.
Page 170: Graphics Capabilities
Graphics capabilities This set of displays tests the screen's capabilities for each graphics mode. During the test, the resolution and mode number appear above an image representing the mode’s capabilities. The number inside the brackets is the mode number. If the image appears normal, press Enter to test the next mode.
Page 171: Hard Disk Test
Floppy disk (Diskette test) After the last graphics display test, the program displays the following prompt: FLOPPY DISK 503000 Mount the work disk(s) on the drive(s), then press [Enter] key [Warning The contents of the disk(s) will be destroyed] If diskette drives are connected, this prompt asks you to insert a diskette into each diskette drive you want to test.
Page 172: Printer Test
Printer test If the hard disk test passes and you selected to test the printer, you see the following message: PRINTER TEST IN PROGRESS 60xxxx where xxxx is a counter that shows the test is still in progress. If you specified an IBM compatible printer, the test prints: If you specified a printer that is not IBM compatible, the test prints: !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmno !"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnop...
Page 173: If You Need Further Assistance
If you need further assistance If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact Toshiba for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 174 9-26 Troubleshooting User's Manual...
Page 175: Appendix A: Specifications
Appendix A Specifications This appendix summarises the computer’s technical specifications. Physical dimensions typical 3.18 kilograms Weight This may vary depending on configuration. 309 (w) 262.5 (d) 44 (h) millimetres Size The configuration with the 15” screen is slightly larger. Environmental Requirements Conditions Ambient Relative humidity...
Page 176: Power Requirements
Power Requirements 60 watts for the 4300 Series AC adaptor 45 watts all other models 100 - 240 volts AC 50 or 60 hertz (cycles per second) 4300 Series Amperes All other models 15 Volts DC Computer Processor The computer is equipped with a Mobile Built-in Pentium®...
Page 177 Disks Satellite Pro 4270/4280: 6.0* gigabyte hard disk Internal hard disk drive Satellite Pro 4320: 12* gigabyte hard disk drive * one gigabyte means one billion byte Accommodates either 3 ½" 1.44-megabyte or Diskette drive 720-kilobyte diskettes. Maximum 24-speed CD-ROM installs in the CD-ROM drive computer.
Page 178 Ports Parallel printer or other parallel device Parallel (ECP compatible) RS-232C compatible port Serial (16550 UART compatible) 15-pin, analogue VGA port supports VESA External monitor DDC2B compatible functions. Connects an external PS/2 mouse or PS/2 PS/2 Mouse/ keyboard Keyboard Enables connection of a monaural microphone Microphone Enables connection of a stereo headphone Headphone...
Page 179: Pc Card Slot
It also has a volume control dial. Software Windows operating system, Toshiba Utilities and Standard drivers preloaded on hard disk. User's Manual Specifications A-5...
Page 180 Built-in Modem Network control unit (NCU) Type of NCU Telephone line (analog only) Type of line Pulse Type of dialling Tone AT commands Control command EIA-578 commands Monitor function Computer’s speaker Communication specifications Data: Full duplex Communication system Fax: Half duplex Data Communication V.21/V.22/V.22bis/V.32/V.3...
Page 181 Options PA Number Article PA3003U-K 32 MB memory kit Memory PA3004U-K 64 MB memory kit PA3005U-K 128 MB memory kit PA3006GR Keycaps for German keyboard Keyboard PA3006FR Keycaps for French keyboard PA3006SC Keycaps for Scandinavian keyboard PA3006SL Keycaps for Swiss keyboard PA3006IT Keycaps for Italian keyboard PA3006SP...
Page 182 This product is approved for electrical safety and/or electromagnetic compatibility (EMC) by the following associations: TÜV DIN GOST TÜV Toshiba declares that this product complies with the following directives to be observed for CE marking. CE-Marking is the responsibility of Toshiba Europe, Hammfelddamm 8, 41460 Neuss, Germany. 93/68/EEC...
Page 183: Appendix B: Ac Power Cord And Connectors
Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: Minimum 2 metres Length:...
Page 184 NEMKO Norway: SEMKO Sweden: Switzerland: United Kingdom: In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.
Page 185: Appendix C: The Toshiba International Warranty
The cover is assured in major industrial countries of the world. It means that wherever you take your Toshiba mobile PC in this area, you will never be left without help should any problems arise.
Page 186 NSW 2113 http://www.isd.toshiba.com.au Toshiba Europe GmbH Tel: +43-1-72031000 Austria Handelskai 388 Fax: +43-1-72031002 1020 Wien http://www.toshiba.at Toshiba Information Systems Benelux B.V. Tel: +32-2-715-8700 Belgium Excelsiorlaan 40, B-1930 Zaventem Fax: +32-2-725-3030 http://www.toshiba.be Toshiba Canada Ltd. Tel: +1-800-663-0378 Canada 191 McNabb Street...
Page 187 Tel: +356-49 36 04 Malta 111 Old Railway Track Fax: +356-49 36 03 HMR-16 St Venera http://www.tabone.com.mt Netherlands Toshiba Information Systems Benelux B.V. Tel: +31-10-2882-300 Rivium Boulevard 41 Fax: +31-10-2882-390 2909 LK Capelle a/d IJssel http://www.toshiba.nl Scribona Norge A/S; Toshiba PC Service...
Page 188 United 9740 Irvine Blvd., Irvine, CA 92713-9724 Fax: +1-949-583-3345 States http://www.toshiba.com Or for all countries not listed, please call the Toshiba International Service Line : Tel: +352 460433 or E-mail: toshibawarranty@unn.unisys.com Toshiba addresses for the Internet/World Wide Web Toshiba Europe Toshiba Japan http://www.toshiba-teg.com...
Page 189: Appendix D: Keyboard Layouts
Appendix D Keyboard Layouts Belgian Canadian User's Manual Keyboard Layouts D-1...
Page 190 Danish French German D-2 Keyboard Layouts User's Manual...
Page 191 Italian Norwegian Polish User's Manual Keyboard Layouts D-3...
Page 192 Portuguese Spanish Swedish D-4 Keyboard Layouts User's Manual...
Page 193 Swiss-German UK English US English User's Manual Keyboard Layouts D-5...
Page 194 D-6 Keyboard Layouts User's Manual...
Page 195: Appendix E: Display Controller And Modes
Appendix E Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors.
Page 196: Video Modes
Video modes The computer supports video modes defined in the following table. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colours and refresh rates. Also, consider that if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Page 197 Table 1. Video modes Type Resolution Character Scanning matrix (pels) colours colours frequency Ver./Hor. SVGA Grph 800 x 600 Pels 8 x 16 256 of 256k 256 of 256k 60/75/85Hz 37.8/46.9/53.7kHz SVGA Grph 1024 x 768 Pels 8 x 16 256 of 256k* 256 of 256k 60/75/85Hz...
Page 198 E-4 Display Controller and Modes User's Manual...
Page 199: Appendix F: If Your Computer Is Stolen
What is your address, phone, and fax number? To register the theft, please follow these procedures: Fill in the Toshiba Theft Registration form (or a copy of it) below. Attach a copy of your receipt showing where your computer was purchased.
Page 200: Toshiba Theft Registration
Toshiba Theft Registration Send to: Toshiba Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Satellite Pro 4280) Model number: (e.g. PA1218E YXT) Serial number: (e.g. 70123456E)
Page 201: Appendix G: Ascii Character Codes
Appendix G ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, Keyboard).
Page 202 Sort Ctrl code code char char G-2 ASCII Character Codes User's Manual...
Page 203 Sort Sort code code char code code char User's Manual ASCII Character Codes G-3...
Page 204 Sort Sort code code char code code char G-4 ASCII Character Codes User's Manual...
Page 205 Sort Sort code code char code code char User's Manual ASCII Character Codes G-5...
Page 206 Sort code code char G-6 ASCII Character Codes User's Manual...
Page 207: Appendix H: International Modem Guide
Appendix H International Modem Guide When you are familiar with the procedures and information in this guide, carefully follow the steps described for installing the international modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the modem To install the modem follow the procedures below.
Page 208 Thread the modem cable into the hole shown below and fit the modem jack into its slot. Seating the modem jack Seat the cover and press to secure the latches. Be sure the jack fits the hole in the cover properly. Secure the cover with one screw.
Page 209: Replacing The Keyboard
Connecting the modem board To connect the modem board, follow the steps below. Connect the cable. Align the connectors and seat the modem board. Press to ensure a firm connection. Secure the modem board with two screws. Removing two screws and opening the keyboard Replacing the keyboard To replace the keyboard, follow the steps below.
Page 210 Removing the international modem To remove the modem. Remove the battery Move the keyboard back. Remove the internal modem board. Remove the modem jack and cable. Secure the modem slot cover. Replace the keyboard and secure the braces. Install the battery pack. Refer to the installation procedures for details.
Page 211: Glossary
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. AccuPoint II: A pointing device integrated into the Toshiba computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Page 212 asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer.
Page 213 cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
Page 214 commands: Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices. communications: The means by which a computer transmits and receives data to and from another computer or device. See parallel interface; serial interface. compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred.
Page 215 data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve.
Page 216 echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT.
Page 217 See also software and firmware. Hardware Setup: A Toshiba utility that lets you set the parameters for various hardware components. hertz: A unit of wave frequency that equals one cycle per second.
Page 218 I/O devices: Equipment used to communicate with the computer and transfer data to and from it. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 219 level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing- side coating is etched into character forming segments with leads that extend to the edge of the glass.
Page 220 mode: A method of operation, for example, the boot mode or the resume mode. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment.
Page 221 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility): A Toshiba utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 222 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. Toshiba portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 223 SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. serial communications: A communications technique that uses as few as two interconnecting wires to send bits one after another. serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time.
Page 224 TDIAG: A Toshiba diagnostic program used for testing and configuring the computer system’s resources. terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 225: Index
Index AC adaptor, 1-3, 1-11, 2-13, 8-12 Card Station III, 1-11, 8-15 connecting, 3-5, 8-14 back, 8-17 AccuPoint II connecting, 8-20 problems, 9-11 front, 8-16 using, 4-1 left side, 8-19 AccuPoint™ II, 1-3, 2-8, A-5 right side, 8-17 AccuPoint™ II control buttons, 2-8 Card Station IV, 1-11, 8-8 ASCII characters, 5-8, G-1 back, 8-10...
Page 226 DC IN features indicator, 6-3 special, 1-7 Diagnostic test Features, 1-2 choosing options, 9-18 Fn + F1 (instant security), 5-4 execution, 9-17 Fn + F2 (power save mode), 5-5 sequence, 9-19 Fn + F3 (resume mode/boot mode), subtests, 9-19 display, 9-20 Fn + F4 (alarm volume), 5-5 hard disk, 9-23 Fn + F4 (speaker volume), 5-5...
Page 227 Monitor. See also Video modes and Display Keyboard, 1-3, A-3 external, 8-33 emulating keys on enhanced external port location, 2-4 keyboard, 5-3 Monitor external F1...F12 function keys, 5-2 problems, 9-13 light grey keys, 5-1 Mouse problems, 9-6 PS/2 soft keys problems, 9-12 Fn key combinations, 5-3 serial...
Page 228 9-11 panel power off, 1-8 self test, 9-3 panel power on/off, 6-13 sound system, 9-14 ring indicator power on, 6-14 support from Toshiba, 9-25 turning off, 3-7 system start-up, 9-3 turning on, 3-6 TV output signal, 9-15 POWER, 8-19...
Page 229 Real time clock battery, 6-4 The Euro symbol, 5-2 Region codes, 2-11 Troubleshooting. See Problems Reset button, 2-3 TSETUP, 6-13, 7-1 Restarting the computer, 3-7 definition, 1-10 Resume (Suspend, Standby), 1-9 options, 7-4 Retaining data with power off, 6-8 alarm volume, 7-11 Ring indicator, 1-8 auto power on, 6-13 Ring indicator power on, 6-14...
Page 230 Index 6 User's Manual...

This manual is also suitable for:

Satellite pro 4200 series

Toshiba Satellite Pro 4300 User Manual

Preface

Manual Contents

Conventions

Chapter 1: Introduction

Equipment Checklist

Features

Special Features

Utilities

Options

Chapter 2: The Grand Tour

Front with the Display Closed

Left Side

Right Side

Back Side

Underside

Front with the Display Open

Indicators

Drives

AC Adaptor

Chapter 3: Getting Started

Setting up

Connecting the AC Adaptor

Opening the Display

Turning on the Power

Turning off the Power

Restarting the Computer

Restoring the Preinstalled Software

Chapter 4: Operating Basics

Using Accupoint™ II

Using CD-ROM/DVD-ROM Drives

Disk Care

International Modem

Video out

Cleaning the Computer

Moving the Computer

Heat Dispersal

Chapter 5: The Keyboard

Grey Keys

F1...F12 Function Keys

Soft Keys: Alt Gr Key Combinations

Soft Keys: Fn Key Combinations

Keypad Overlay

Generating ASCII Characters

Chapter 6: Power and Power-Up Modes

Power Conditions

Power Indicators

Battery Types

Care and Use of the Battery Pack

Replacing the Battery Pack

Starting the Computer by Password

Power-Up Modes

Panel Power off

System Auto off

Auto Power on

Ring Indicator Power on

Chapter 7: Setup and Password Security

Tsetup

Password Security

Chapter 8: Optional Devices

PC Cards

Memory Expansion

Additional Battery Pack

Battery Charger

Card Station IV

Card Station III

Port Replicator

Parallel Printer

External Monitor

PS/2 Mouse

PS/2 Keyboard

Security Lock

Chapter 9: Troubleshooting

Problem Solving Process

Hardware and System Checklist

Diagnostic Test

If You Need Further Assistance

Appendix A: Specifications

Appendix B: AC Power Cord and Connectors

Appendix C: the Toshiba International Warranty