Summary of Contents for Eagle A100
-
Page 1: Maintenance Instructions
EAGLE Installation, Operation and Maintenance Instructions Lubrication information is in Section III-A, Item 1b. and Section IV-A. EAGLE MODEL A100 ANSI PUMPS... -
Page 2: Table Of Contents
SECTION I—GENERAL Introduction ... 3 Importance of Instructions ... 3 Special Warnings ... 3 Receiving Inspection—Shortages... 3 Preservation and Storage... 3 Handling Techniques... 3 SECTION II—INSTALLATION II-A Location... 3 II-B Foundations ... 3 II-C Leveling and Grouting of Baseplate ... 4 II-D Piping Practices ... -
Page 3: Section I-General
This instruction manual is intended to assist those involved with the installation, operation and maintenance of Eagle Model A100 pumps. It is recommended that this manual be thoroughly reviewed prior to installing or performing any work on the pump or motor. -
Page 4: Ii-C Leveling And Grouting Of Baseplate
II-C. Leveling and Grouting of Baseplate Initial Alignment Check 1. Put the unit in place on wedges located at four points as shown in Fig. 2. Some long installations may require additional wedges near center of bedplate. WEDGES Figure 2 2. -
Page 5: Ii-F Stuffing Box
WEDGES Figure 3 Figure 4 Figure 4 SECTION III—OPERATION III-A. Startup 1. Check List Lubrication—Pump bearings are normally oil lubricated. (THE BEARINGS ARE NOT LUBRICATED AT THE FACTORY.) These pumps are supplied with an oiler which maintains a constant oil level in the bearing frame. Locate oiler as shown on the outline drawings supplied for the unit. -
Page 6: Iii-B Operation Checks
Oil Mist lubrication of bearings is available on A100–X frames. This can be supplied at time of order, or field conversion can be done. Refer to the instructions of the manufacturer of the Oil Mist System. -
Page 7: Section V-Disassembly And Reassembly
SECTION V—DISASSEMBLY AND REASSEMBLY V-A. Disassembly (refer to Sectional Views in Part VI) 1. Prepare pump for disassembly as follows: Lock out power supply to motor. b. Shut off valves controlling flow to and from pump. Flush pump of all corrosive or toxic liquid, if required. d. - Page 8 4. On S, M and L models, insert retaining ring (361A) into groove in bearing housing (134A). Flat side of retaining ring must be against bearing (112A). On X units, slide bearing end cover (109A) and gasket (360C) on shaft. Ensure the “top” of end cover (109A) lines up with the “top”...
-
Page 9: V-D Additional Details
13. Place casing gasket (351) against shoulder in casing. 14. Slide the pullout assembly into the casing (100). Drain slot in stuffing box cover (184) should line up with drain connection in casing. Install frame–to–casing bolts (370) and tighten evenly while rotating shaft (122) by hand. -
Page 10: Recommended Spare Parts
Parts List and Materials of Construction No. Reqd. Item No. Per Pump Part Name Casing Impeller Lantern Ring 1 Set Stuffing Box Packing Gland (Packed Box) Frame Adaptor 109A Bearing End Cover 112A Ball Bearing-Outboard 113A Bearing Frame Breather Pump Shaft (Less Sleeve) 122* 122A Pump Shaft (With Sleeve) - Page 11 Assembly View of 8” Pumps Only 469D 412A Model A100 S, M, L 370H 113A 361A 136 & 382 122A 333A 228A 370C 168A 370D 332A 134A 112A...
-
Page 14: Section Vii-Trouble Shooting
SECTION VII—TROUBLE SHOOTING Possible Causes Problem & Corrections A. No liquid delivered, 1, 2, 3 ,4, 5, 6, 7, 8, 9, not enough liquid 10 11, 12, 13, 14, 18, delivered, or not 19, 20. enough pressure B. Pump works a while 4, 5, 7, 8, 9, 11, 12, 20. -
Page 15: Troubleshooting
SECTION VIII—ORDERING SPARE PARTS VIII-A. Spare Parts To insure against possible long and costly downtime periods, especially on critical services, it is advisable to have spare parts on hand. 1. For critical services: It is recommended that a “back pull–out assembly”... - Page 16 EAGLE EAGLE PUMP & COMPRESSOR LTD. 7025 - 5 Street S.E., Calgary, AB T2H 2G2 Canada ANSI Centrifugal Pumps Multistage Horizontal Pumps Vertical Sump Pumps Rotary Screw Compressor Air/Gas Dryers www.eagle-pc.com 01/2000 Printed in Canada...