hit counter script
Download
Share
Print this page
Sony VPL-FHZ131L Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Projector
  5. VPL-FHZ131L
  6. Service manual
Sony VPL-FHZ131L Service Manual

Sony VPL-FHZ131L Service Manual

Hide thumbs Also See for VPL-FHZ131L:

Advertisement

Quick Links

Download this manual
DATA PROJECTOR
VPL-FHZ131L
VPL-FHZ101L
VPL-FHZ91L
VPL-F1301ZL/F1306ZL
VPL-F1001ZL/F1006ZL
VPL-F901ZL/F906ZL
REMOTE COMMANDER
RM-PJ30
利用条件: 
①  本情報はソニー製品の販売、設置、設定、使用の目的でのみご利用ください。かかる目的以外での利用を禁止します。
②  著作者の事前の書面による許可なく、本情報の全部または一部の複写、複製、転載、改変、翻訳、送信等を禁止します。
情報改訂:
本情報は、当社の裁量により、予告なく変更されることがあります。ご使用される場合、本情報が最新の情報であることを確認のうえ、
ご使用ください。
Conditions of Use:
(1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information
for any purpose other than the purpose described foregoing is forbidden.
(2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior
written permission of the author.
Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before
using it.
SERVICE MANUAL
1st Edition

Advertisement

loading

Related Manuals for Sony VPL-FHZ131L

Summary of Contents for Sony VPL-FHZ131L

  • Page 1 ご使用ください。 Conditions of Use: (1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information for any purpose other than the purpose described foregoing is forbidden. (2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
  • Page 2 Netzkabel muß mit einer in der Nähe For kundene i Norge des Geräts befi ndlichen, leicht zugänglichen Wandsteckdose verbunden werden, damit sich bei Dette utstyret kan kobles til et IT-strømfordelingssystem. einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen läßt. VPL-FHZ131L...
  • Page 3 Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. 1 (P) VPL-FHZ131L...
  • Page 4 ATTENTION RISQUE D’ÉLECTROCUTION Le fusible du circuit primaire de ce produit peut être connecté sur le côté de fi l neutre. Déconnectez l’appareil de l’alimentation pour éviter un choc électrique lors de la réparation. 2 (P) VPL-FHZ131L...
  • Page 5 す。 This unit is classifi ed as a CLASS 3R LASER PRODUCT to IEC 60825-1:2007. The CLASS 3R LASER PRODUCT label is located on the left side of Base unit. 本機は IEC 60825-1:2007 では，CLASS 3R PRODUCT に分類 されています。CLASS 3R LASER PRODUCT ラベルは，本機 の左側面のベースユニットに貼られています。 3 (P) VPL-FHZ131L...
  • Page 7 Power Boards ..........1-63 (E) 1-6-12. Optical Block Assembly ........1-20 (E) 1-6-13. CSC Unit 1-15. Power Cord ..............1-64 (E) (VPL-FHZ131L/F1301ZL/F1306ZL) ...1-21 (E) 1-6-14. DC Fan 6, DC Fan 11, DC Fan 12 and 2. Adjustments DC Fan 13 ............1-22 (E) 1-6-15.
  • Page 8 Light Source Unit and Fan Block 1 ......... 3-8 Light Source Unit and Fan Block 2 ....... 3-10 Power Unit 1..............3-11 Power Unit 2..............3-12 Bottom Cover Block............3-14 Optics Block ..............3-16 3-3. Packing Materials & Supplied Accessories ....3-18 2 (E) VPL-FHZ131L...
  • Page 9 (within the distance of injury) during the operation of the RG3 product may lead to the light injury, even momentarily. . When performing the operation with this unit lighting, use the optional lens VPLL-4008, VPLL-Z4107, VPLL-Z4111, VPLL-Z4015 or VPLL-Z4019 except when VPLL-Z4025 or VPLL-Z4045 is necessary. 1-2. Appearance Figure RM-PJ30 1-1 (E) VPL-FHZ131L...
  • Page 10 4. Remove the lens in the direction of the arrow (D). Lens Hooks Slide switch Lens cover release buttons Lens cover assembly Lens cover Lever 5. Attach the lens cover in the reverse order of step 1. 1-2 (E) VPL-FHZ131L...
  • Page 11 MB board G board (power unit) ST board SB1 board V board SC board NF board TA board 1: Parts packed in shift unit assembly C board AR board 2: Parts packed in optical block assembly Fan locations 1-3 (E) VPL-FHZ131L...
  • Page 12 . Do not release the protection circuit with the cabinet removed. Inappropriate use of the laser diode may cause damage to eyes or skin. . In order to avoid inappropriate use of the laser diode, do not disassemble the light source unit. 1-4 (E) VPL-FHZ131L...
  • Page 13 1-6-4. C Board 1-6-7. DC Fan 1, DC Fan 2, 1-6-6. DC fan 7, DC fan 8, 1-6-15. DC Fan 14 and DC Fan 3 and V Board DC fan 9 and DC fan 10 DC Fan 15 1-5 (E) VPL-FHZ131L...
  • Page 14 1-6-8. TA Board and DC Fan 4 1-6-10. Light Source Unit 1-6-16. Power Unit 1-6-9. ST Board 1-6-12. Optical Block Assembly 1-6-17. LD Board (Switching Regulator) 1-6-26. Shift Unit Assembly and 1-6-13. CSC Unit 1-6-18. LD PFC Board Prism Assembly (VPL-FHZ131L/F1301ZL/F1306ZL) (Power Unit) 1-6 (E) VPL-FHZ131L...
  • Page 15 1-6-20. MA Board and B Board 1-6-19. G Board (Power Unit) DC Fan 12 and DC Fan 13 1-6-21. QA Board 1-6-23. F2 Board (Power Unit) 1-6-22. QM Board 1-6-11. DC Fan 5 1-6-25. In-polarizer (R)/(G)/(B) 1-6-27. PS Converter Assemblies Assembly 1-7 (E) VPL-FHZ131L...
  • Page 16 1-6-1. Electrostatic Filter 4 Hold the knob of the 3 Filter holder filter holder and remove it in the direction of the arrow (A). Knob 2 Three screws (with drop-safe) 1 Filter cover 5 Electrostatic filter 1-8 (E) VPL-FHZ131L...
  • Page 17 8 Two screws (PSW3 5 Two screws (PSW3 1 Slide the lens cover release 2 Slide the lens cover release button in the direction of the button in the direction of the arrow to unlock. arrow to unlock. 1-9 (E) VPL-FHZ131L...
  • Page 18 1-6-3. MB Board : For VPL-FHZ131L/F1301ZL/F1306ZL 3 Three harnesses CN100 2 Flexible flat cable CN202 CN300 CN500 CN203 5 Seven screws CN201 (PSW3 CN102 CN400 6 MB board CN103 4 Harness CN200 CN101 1 Six harnesses 1-10 (E) VPL-FHZ131L...
  • Page 19 (To SC board) (To DC fan 14 and DC fan 15) CN1504 CN1402 (To prism assembly) (To SB1 board) CN1506 CN1505 (To prism assembly) (To prism assembly) CN1300 (To prism assembly) CN1200 (To prism assembly) CN1100 (To prism assembly) 1-11 (E) VPL-FHZ131L...
  • Page 20 5 Two radiation sheets (30 (PSW3 0 Two harnesses ![ C board 7 Three harnesses !] Six screws 9 Three harnesses (PSW3 8 Three harnesses !; Six screws (PSW3 !\ GND plate (B-C) !, Gasket (U4) !' C bracket 1-12 (E) VPL-FHZ131L...
  • Page 21 1-6-5. NF Board 1 Remove the NF board from the two hooks. 2 Harness CN100 3 NF board 1-13 (E) VPL-FHZ131L...
  • Page 22 The lock is released when the hook of the fan spacer is pulled Label side in the direction of the arrow (A). 6 Two harnesses 0 DC fan 9 7 Harness 5 Harness CN100 NR board ST board CN100 1-14 (E) VPL-FHZ131L...
  • Page 23 !\ DC fan 1 8 Relay connector Label side 9 Harness cushion Label (FAN_1) != Relay connector !, Three screws ![ Harness cushion Label side (PSW3 !. DC fan 2 Label (FAN_2) !' Harness cushion !; Relay connector 1-15 (E) VPL-FHZ131L...
  • Page 24 !- Filter box top Label side 6 Two screws (PSW3 7 DC fan 4 5 PSC holder assembly 8 Harness CN100 4 Four screws 0 TA board (BVTP3 9 Screw (BVTP3 3 Filter box bottom 2 Five screws (BVTP3 1-16 (E) VPL-FHZ131L...
  • Page 25 1-6-9. ST Board 1 Screw (PSW3 2 ST board 1-17 (E) VPL-FHZ131L...
  • Page 26 8 Hold the handle and pull up the light source unit in the direction of the arrow. 6 Harness When removing or installing the light source unit, do not touch the wheel 7 Light source unit portion, lens portion and heat sink. 1-18 (E) VPL-FHZ131L...
  • Page 27 1-6-11. DC Fan 5 3 Two screws 2 Harness cushion (PSW3 5 DC fan 5 Label side 4 Wheel (IN2) duct 1 Relay connector 1-19 (E) VPL-FHZ131L...
  • Page 28 1-6-12. Optical Block Assembly The optical block assembly is not supported by service. 2 Screws (PSW4 16 (with drop-safe)) 1 Six screws (PSW4 VPL-FHZ131L/F1301ZL/F1306ZL 4 Harness CSC unit 3 Optical block assembly 1-20 (E) VPL-FHZ131L...
  • Page 29 1-6-13. CSC Unit (VPL-FHZ131L/F1301ZL/F1306ZL) 1 Three screws (PSW3 2 CSC unit Optical block assembly 1-21 (E) VPL-FHZ131L...
  • Page 30 ![ DC fan 13 4 Screw (BVTP3 Label !; Harness side Label side !' Exhaust duct base 0 Exhaust duct cap Label Label side side 5 Relay connector !] DC fan 6 != DC fan 12 9 Two screws (BVTP3 1-22 (E) VPL-FHZ131L...
  • Page 31 (BVTP3 Fan spacer Hook !\ Two screws (BVTP3 3 Cover lens side The lock is released when the hook of the fan spacer is pulled in the direction of the arrow (A). !; Front fan case (bottom) 1-23 (E) VPL-FHZ131L...
  • Page 32 1 Five screws (PSW4 8 Eight screws (PSW3 2 Optical base 3 Six screws (PSW3 4 Heat exchanger (WHL) 6 Harness 9 Power block CN102 7 Harness CN103 5 Open the edge saddle. F2 board (power unit) 1-24 (E) VPL-FHZ131L...
  • Page 33 !' LD board (switching regulator) !\ Harness !; Two harnesses 5 Screw (PSW3 !] LD case != Open the two edge saddles, then remove the four harnesses. ![ Open the two edge saddles, then remove the harness. 1-25 (E) VPL-FHZ131L...
  • Page 34 2 Open the two edge saddles, then remove the three harnesses. CN1101 CN1113 CN1105 5 Harness CN1112 G case 6 Two harnesses 4 Harness 7 Four screws 8 G board (power unit) (PSW3 1-26 (E) VPL-FHZ131L...
  • Page 35 !\ B-MA bracket !' Harness @/ Radiation sheet (30 !, Two harnesses !; Four harnesses CN900 CN203 @= B board CN700 CN202 !. Fine-wire coaxial cable CN201 CN1201 CN1200 CN200 CN1202 @- Radiation sheet (PD) B to B 1-27 (E) VPL-FHZ131L...
  • Page 36 1-6-21. QA Board 6 Two screws 5 Two screws (PSW3 (PSW3 7 Screw (PSW3 8 QA bracket assembly 4 Two screws 2 Two screws (PSW3 3 Terminal cover 1 Terminal cover ACC 1-28 (E) VPL-FHZ131L...
  • Page 37 !] Ground wire 9 Harness QA bracket assembly CN1902 CN500 ![ Screw (PSW3 !; Eight hexagonal screws !\ Two screws (BVTP3 0 Fine-wire coaxial cable !- Fine-wire coaxial cable QA board CN9001 CN9002 QM board != Harness 1-29 (E) VPL-FHZ131L...
  • Page 38 1-6-22. QM Board 3 QA bracket 1 Three screws (PSW3 2 QM board 1-30 (E) VPL-FHZ131L...
  • Page 39 (power unit) CN103 (PSW3 2 F case assembly 6 Two harnesses 5 Edge saddle 8 F2 board (power unit) F2 board (power unit) CN101 6 Two harnesses 3 Edge saddle 4 Harness 7 Five screws (PSW3 4 Harness 1-31 (E) VPL-FHZ131L...
  • Page 40 1-6-24. NR Board 2 Remove the NR board from the hook. 1 Harness CN100 3 NR board 1-32 (E) VPL-FHZ131L...
  • Page 41 When attaching the in-polarizer (R)/(G)/(B) assemblies, attach them so that each screw is located at the center of the elongate hole. Elongate hole Screw In-polarizer (G) assembly In-polarizer (B) In-polarizer (R) assembly assembly Elongate hole Elongate hole Screw Screw 1-33 (E) VPL-FHZ131L...
  • Page 42 5 Two screws (PSW4 2 Harness 7 Three screws (PSW3 0 Back correct glass assembly 6 Illumination unit assembly 8 Prism assembly 9 Three screws (PSW3 To C board 3 Two harnesses AR board !- Shift unit assembly 1-34 (E) VPL-FHZ131L...
  • Page 43 When replacing the PS converter assembly, perform the procedure in Section 2-2-5. 1 Eleven screws (PSW3 2 Cover (RGB) 3 PS converter assembly Marking Attach the PS converter assembly so that the marking on the PS converter is located as shown in the illustration. Optical block assembly 1-35 (E) VPL-FHZ131L...
  • Page 44 . When the operating sound is not heard: The auto filter cleaning function has failed. Replace the plunger solenoid in the following procedure. (Refer to “Replacement of plunger solenoid”.) After replacing the plunger solenoid, if the function does not operate, replace the C board. (Refer to Section 1-6-4.) 1-36 (E) VPL-FHZ131L...
  • Page 45 6. Remove the five screws, then remove the filter box bottom. 7. Remove the PSC holder sheet. 8. Remove the four screws, then remove the PSC holder sheet assembly. Filter box top PSC holder sheet PSC holder assembly BVTP BVTP Filter box bottom 1-37 (E) VPL-FHZ131L...
  • Page 46 9. Remove the two screws, then remove the DC fan 4. DC fan 4 PSC holder assembly 10. Remove the four screws, then remove the plunger solenoid. PSC holder Plunger solenoid 1-38 (E) VPL-FHZ131L...
  • Page 47 The following part cannot be reused. When replacing the plunger solenoid, prepare the new part. . Cushion (solenoid): Part number 4-741-539-01 Plunger solenoid Cushion (solenoid) 12. Perform steps 1 to 10 in the reverse order to attach the plunger solenoid. 1-39 (E) VPL-FHZ131L...
  • Page 48 2. While pushing the slide switch in the direction of the arrow (A), move the lever upward as far as it will go in the direction of the arrow (B). 3. Remove the lens in the direction of the arrow (C). Slide switch Lever Lens Lever 1-40 (E) VPL-FHZ131L...
  • Page 49 Slide switch Lever Lens Lever 3. Attach the lens cover and slide the two lens cover release buttons in the directions of the arrows to lock the lens cover. Lens cover release buttons Lens cover Lens cover 1-41 (E) VPL-FHZ131L...
  • Page 50 (R) assembly because they are inorganic polarizing plates. If you touch the glass portion, the polarized layer may be peeled off, causing an optical failure. Required items Air dust spray, blower, drinking water, tissue paper Preparation Remove the in-polarizer (R)/(G)/(B) assemblies. (Refer to Section 1-6-25.) 1-42 (E) VPL-FHZ131L...
  • Page 51 Attach the in-polarizer (R)/(G)/(B) assemblies so that each screw is located in the center of the elon- gate hole. in-polarizer (G) assembly The screw is located in the center of the elongate hole. Optical block assembly (top view) 1-43 (E) VPL-FHZ131L...
  • Page 52 Remove the optical block assembly. (Refer to Section 1-6-12.) Procedure 1. Remove the eleven screws, then remove the cover (RGB). 2. Remove the GB reflection dichroic mirror, G reflection dichroic mirror, B channel mirror, B mirror 2 and R mirror. 1-44 (E) VPL-FHZ131L...
  • Page 53 3. Wipe off the dust and dirt adhered to the removed optical parts on both sides with the tissue paper dampened with drinking water. Cover (RGB) R mirror Marking GB reflection dichroic mirror B mirror 2 Sand-finished Markings rear surface G reflection dichroic mirror B channel mirror Blue marking on rear surface 1-45 (E) VPL-FHZ131L...
  • Page 54 2 and R mirror, pay attention to the marking position. . When attaching the G condenser lens, R sub-condenser lens, R condenser lens, B condenser lens and relay lens 1, pay attention to the lens direction. 1-46 (E) VPL-FHZ131L...
  • Page 55 1. Remove the eleven screws, then remove the cover (RGB). 2. Remove the PS converter assembly. Cover (RGB) PS converter assembly Marking First fly-eye lens Second fly-eye lens PS converter assembly 1 Wipe one side. 2 Wipe the other side. 1-47 (E) VPL-FHZ131L...
  • Page 56 Remove the optical block assembly. (Refer to Section 1-6-12.) Procedure 1. Blow off the dust and dirt adhered to the portions A (liquid crystal plate and out-polarizer) using the air dust spray or blower. Portions A Prism assembly (top view) 1-48 (E) VPL-FHZ131L...
  • Page 57 . When using the optional lens VPLL-Z4025 or VPLL-Z4045, this unit is categorized as the product of risk group 3 (RG3). Therefore, use the optional lens VPLL-4008, VPLL-Z4107, VPLL-Z4111, VPLL- Z4015 or VPLL-Z4019 during operation and avoid using the RG3 lens. 1-49 (E) VPL-FHZ131L...
  • Page 58 Service Kit Assembly (POLARIZATION) (A-2224-132-A) XC1 board XC2 board XC3 board A MB-AR_1 B MB-AR_2 C XC1-C_1 D XC1-C_2 E XC2-C_1 F XC2-C_2 G XC2-MB_1 H XC2-MB_2 I FFC Service Kit Assembly (A-1806-410-A) XF92 board J XF92 flexible wiring board 1-50 (E) VPL-FHZ131L...
  • Page 59 XF92 boards XC2 board XC1 board CN2302 CN2300 CN205 CN209 CN2301 CN206 CN203 CN204 CN305 CN103 CN207 CN202 CN102 CN208 CN201 CN200 CN101 CN402 CN403 CN100 CN104 CN304 CN303 CN400 CN401 XC3 board XF92 board CN500 CN501 1-51 (E) VPL-FHZ131L...
  • Page 60 . When this unit is connected to LAN, connect PC to the LAN and adjust the PC network setting to the LAN environment. 3. Check of IP address Turn on the power of this unit to display the menu screen. Check the IP address of this unit on the [Con- nection/Power Menu] screen of the menu. 1-52 (E) VPL-FHZ131L...
  • Page 61 . User name: service . Password: (model name in half-width lowercase characters) Example) vpl-fhz131l, vpl-fhz91l When moving from the service mode to other page and entering the service mode again, close the Web browser once, and then start the browser again.
  • Page 62 IPv4: http:// (IP address of this unit) IPv6: http:// [xxxx:xxxx:~xxxx] (3) Click the Setup tab. (4) Type the user name and password. (Refer to “4. Access authority in the function for service” in Sec- tion 1-11-2.) (5) Click the [Password] button. 1-54 (E) VPL-FHZ131L...
  • Page 63 (2) Type the following in the address bar of the Web browser. IPv4: http:// (IP address of this unit) IPv6: http:// [xxxx:xxxx:~xxxx] (3) Click the Setup tab. (4) Enter the user name and password. (Refer to “4. Access authority in the function for service” in Section 1-11-2.) 1-55 (E) VPL-FHZ131L...
  • Page 64 (5) Press the [Apply] button. (6) Press the [OK] button in the confirmation message. (7) Wait until the system is restarted after the setting has been reflected. (8) Perform “2. Check Procedure” to check that the setting has been completed. 1-56 (E) VPL-FHZ131L...
  • Page 65 1-12. Location Information of the Labels SY/IN model Light source specifications Beam divergence angle from lens of this unit 4.7 W laser diodes 64 pcs (VPL-FHZ131L) 48 pcs (VPL-FHZ101L/FHZ91L) Laser emission port Wavelength: 450 - 460 nm Lens Zoom maximum:...
  • Page 66 (center) and the front of the cabinet. Lens VPLL-4008 98 mm VPLL-Z4015 88 mm VPLL-Z4111 123 mm VPLL-Z4019 67 mm VPLL-Z4025 96 mm VPLL-Z4045 93 mm VPLL-Z4107 124 mm Front of the cabinet Front of the lens 1-58 (E) VPL-FHZ131L...
  • Page 67 CN model 64 pcs (VPL-F1301ZL/F1206ZL) 20 pcs (VPL-F1001ZL/F1006ZL/F901ZL/F906ZL) VPLL-Z4107 1-59 (E) VPL-FHZ131L...
  • Page 68 (EEPROM) normally. System error 3 The main CPU does not operate normally. System error 4 The main CPU does not operate normally. Self-diagnostic error The program configuration for the main CPU is not correct. 1-60 (E) VPL-FHZ131L...
  • Page 69 The luminance has exceeded the allowable range. Assembling error The connector of temperature sensor is disconnected. Lens operation error The control of lens shift, zoom and focus cannot be performed correctly. (An error is detected during the execution of the Position memory function.) 1-61 (E) VPL-FHZ131L...
  • Page 70 The MB board drives the seven fans (DC fans 1 to 5, 7 and 8) arranged near the filter and in the center of the unit. The MB board drives a phosphor wheel, CSC filter, solenoid, and electric lens. H board The H board mounts the control panel buttons of this unit. 1-62 (E) VPL-FHZ131L...
  • Page 71 LD PFC board The LD PFC board generates laser driving system power (380 V). LD board (Switching regulator) The LD board steps the primary power (380 V) in the laser driving system down to the secondary power (68 V). 1-63 (E) VPL-FHZ131L...
  • Page 72 LA board mounts the temperature sensor. 1-15. Power Cord To get a power cord, please contact your local Sony Sales Office/Service Center. . Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
  • Page 73 2. Write the Prism (or Main) data supplied with the prism assembly using Quick Access3. (Refer to Section 2-7-6.) 3. Perform the laser luminance and luminance sensor adjustment. (Refer to Section 2-4.) 4. Check the white balance state, and perform the adjustment as required. (Refer to Section 2-3-3.) 2-1 (E) VPL-FHZ131L...
  • Page 74 3. Overwrite the Lens Shift data on PC with the six data values obtained by reading the QR code, and save it. QR code and reading example The latter 6 values are the related data in the order of V_CENTER/H_CENTER/BOTTOM_LIMIT/ TOP_LIMIT/RIGHT_LIMIT/LEFT_LIMIT. 2-2 (E) VPL-FHZ131L...
  • Page 75 The charging is performed automatically in the standby state. When the charging to the backup power supply is insufficient, the writing of time in RTC cannot be performed normally. 7. Write the time in RTC. (Refer to “Time Setting” in Section 1-11-3.) 2-3 (E) VPL-FHZ131L...
  • Page 76 Allow the warm-up time of 10 minutes after the power is on before starting the V COM and white balance adjustments. How to enter the service mode For details on how to enter the service mode, contact your local Sony Sales Office/Service Center. How to enter the advanced user mode 1. Press the [MENU] button.
  • Page 77 6. Select the menus in the following order: Installation → Image Flip and set it to either “V” or “HV”. 7. Perform the steps 2 to 5. 8. Select the menus in the following order: Installation → Image Flip and set back to “Off”. 2-5 (E) VPL-FHZ131L...
  • Page 78 (6) Repeat steps (2) to (5) until the chromaticity (x ?0.002, y ?0.002) with reference to the target chro- maticity (x, y). (7) Select the menus in following order: Device → Memory Save. Select [YES], and press the [ENTER] button to save. 2-6 (E) VPL-FHZ131L...
  • Page 79 (6) Repeat steps (2) to (5) until the chromaticity (x ?0.002, y ?0.002) with reference to the target chro- maticity (x, y). (7) Select the menus in following order: Device → Memory Save. Select [YES], and press the [ENTER] button to save. 2-7 (E) VPL-FHZ131L...
  • Page 80 . Bandpass filter (product code: #86-350) made by Edmund Optics or the equivalent . Personal computer (PC) . RS-232C cross cable . Brightness Adjustment Tool software For obtaining the software, please contact your local Sony Sales Office/Service Center. 2-8 (E) VPL-FHZ131L...
  • Page 81 Create the aperture with the following specifications. . Φ7.0 mm . t = 0.3 mm or less . Color: Black . Metal (aluminum, etc.) 7. Set the laser power sensor as follows. . Filter: . Range: 300 mW . Wavelength: 455 nm 2-9 (E) VPL-FHZ131L...
  • Page 82 4. Install the Laser Projector Service Tool software in PC. 5. Start the Laser Projector Service Tool software. The read value of register is not updated automatically. Click the [Read] button as required for updating to the latest information, and then use it. 2-10 (E) VPL-FHZ131L...
  • Page 83 8. Click the Brightness Adjust tab, and then set the following two registers as follows. . ROB_BRT_SENS_DAC_VAL: Luminance sensor 1-threshold register: 255 . Ruby_BRT_SENS_DAC_VAL: Luminance sensor 2-threshold register: 255 9. Check the value of “LAMP_MAX_DUTY” as follows. . VPL-FHZ131L/F1301ZL/F1306ZL: 216 . VPL-FHZ101L/F1001ZL/F1006ZL: 203 . VPL-FHZ91L/F901ZL/F906ZL: 10. Turn on the power of this unit.
  • Page 84 2-4-4. Luminance Dynamic Range Adjustment 1. Measure the laser power. 2. Check that the laser power does not exceed the output limit value. Output limiting value : . VPL-FHZ131L/F1301ZL/F1306ZL: 350 mW . VPL-FHZ101L/F1001ZL/F1006ZL: 270 mW . VPL-FHZ91L/F901ZL/F906ZL: 270 mW 2-4-5. Electronic Volume Adjustment 1.
  • Page 85 Find a line formula based on the two points, and obtain the DAC value at the point of the electric power threshold limit value. Value to be obtained ROBmax ROB30 P_ROB30 P_ROBmax Electric power threshold limit value 2-13 (E) VPL-FHZ131L...
  • Page 86 2. Disconnect the power cord from this unit. 3. Set the switch (S100) on the NR board to the lower side, then attach the remote control light-receiving window sheet (rear). (Refer to step 1 in Section 2-4-3.) 2-14 (E) VPL-FHZ131L...
  • Page 87 XC3 board respectively. Screw (B2 Screw (B2 In-polarizer assembly (G) In-polarizer assembly (B) In-polarizer assembly (R) Screw (B2 8. Loosen the screw of the in-polarizer assembly (R), then perform step 7. 2-15 (E) VPL-FHZ131L...
  • Page 88 The software can be updated by the method through the network using the Web browser, the method using the USB memory, or the method using ProjectorUpdateTool3. The method to be used may be specified. For details, contact your local Sony Sales Office/Service Center. 2-6-1. Software Update Through “Network” Using Web Browser For the software to be written, contact your local Sony Sales Office/Service Center.
  • Page 89 The file with a different name cannot be updated. (6) Click the [Update] button. The dialog to confirm the file to be updated is displayed. (7) If there is no problem, click the [OK] button. The update is started. 2-17 (E) VPL-FHZ131L...
  • Page 90 Example of Web page during file upload Example of Web page during system upload Example of Web page when the system update has been completed 2-18 (E) VPL-FHZ131L...
  • Page 91 Example of Web page for completion of upload Update Status When the update is properly executed, the following is displayed in Update Status. status update_status complete message success progress 100% updating (7) Disconnect the power cord from this unit. 2-19 (E) VPL-FHZ131L...
  • Page 92 2-6-2. Update Using USB Memory In this unit, the software can be updated by connecting the USB memory to the USB-A connector. For the software to be written, contact your local Sony Sales Office/Service Center. Required equipment . USB memory: USB2.0 compatible...
  • Page 93 The software can be updated by the method to write via RS-232C connector + USB-B connector or the method to update via LAN. For details on ProjectorUpdateTool3 and how to obtain the license, contact your local Sony Sales Office/ Service Center. For the installation method, refer to the document supplied with ProjectorUpdateTool3.
  • Page 94 2-7. Quick Access3 2-7-1. Preparation Required equipment/Tools . Personal computer (PC): RS-232C interface equipped . RS-232C cross cable . QuickAccess3: Executable: QuickAccess3.exe Preparation 1. Install the QuickAccess3 in PC. 2. Connect this unit with PC. RS-232C RS-232C cross cable 2-22 (E) VPL-FHZ131L...
  • Page 95 13. Click the [OK] button. The saving starts. Completed is displayed after completed. 14. Press the [I/O] button and set this unit to standby state. 15. Disconnect the power cord from this unit. 16. Click the [Complete] button. 2-23 (E) VPL-FHZ131L...
  • Page 96 The window displaying the model name of this unit, serial number, and the file path of the destination of the obtained data to save is displayed. 13. Click the [OK] button. The saving starts. Completed is displayed after completed. 14. Disconnect the power cord from this unit. 15. Click the [Complete] button. 2-24 (E) VPL-FHZ131L...
  • Page 97 After completed, The massage “Verify Success! Reading Model Name, Serial Number, NVM Map Version and NVM Data Version is successful.” is displayed. 14. Click the [OK] button. Completed is displayed. 15. Disconnect the power cord from this unit. 16. Click the [Complete] button. 2-25 (E) VPL-FHZ131L...
  • Page 98 The window displaying the model name of this unit, serial number, and the file path of the destination of the obtained data to save is displayed. 12. Click the [OK] button. The saving starts. Completed is displayed after completed. 13. Disconnect the power cord from this unit. 14. Click the [Complete] button. 2-26 (E) VPL-FHZ131L...
  • Page 99 13. Click the [OK] button. The writing starts. Completed is displayed after completed. 14. Press the [I/O] button and set this unit to standby state. 15. Disconnect the power cord from this unit. 16. Click the [Complete] button. 2-27 (E) VPL-FHZ131L...
  • Page 100 The window displaying the file path, model name written in file, unit serial, serial number, and DDC ID is displayed. 13. Click the [OK] button. The writing starts. Completed is displayed after completed. 14. Disconnect the power cord from this unit. 15. Click the [Complete] button. 2-28 (E) VPL-FHZ131L...
  • Page 101 After completed, the massage “Turn Off and On the AC, and then Power On to enable the new set- tings.” is displayed. 14. Click the [OK] button. Completed is displayed. 15. Disconnect the power cord from this unit. 16. Click the [Complete] button. 2-29 (E) VPL-FHZ131L...
  • Page 102 After completed, the massage “Turn Off and On the AC, and then Power On to enable the new set- tings.” is displayed. 13. Click the [OK] button. Completed is displayed. 14. Disconnect the power cord from this unit. 15. Click the [Complete] button. 2-30 (E) VPL-FHZ131L...
  • Page 103 Reality Creation Resolution Noise Filtering Test: On/Off Disable Contrast Enhancer Gamma Mode Gamma3 Gamma3 Gamma3 Gamma3 Color Space Custom1 Custom1 Custom1 Custom3 Custom3 Custom1 Cyan-Red(x) Magenta-Green(y) Color Correction Hue(Red) Saturation(Red) Value(Red) Hue(Yellow) Saturation(Yellow) Value(Yellow) Hue(Green) Saturation(Green) Value(Green) Hue(Cyan) 2-31 (E) VPL-FHZ131L...
  • Page 104 Display only HDBaseT Settings LAN Setting RS-232C Setting RS232C Extron XTP Dynamic Range Input-C AUTO Input-D AUTO Input-E AUTO Input-F AUTO HDMI Cable Normal Input-A Signal Sel. AUTO Input-G Cont. Sel. AUTO With No Input Lamp Cutoff 2-32 (E) VPL-FHZ131L...
  • Page 105 End Pos. Color Blend Fitting (H,V) = (0,0) (ALL Point) Zone Black Level Zone Fitting (H,V) = (0,0) (ALL Point) Black Level Adj. Zone1 R Zone2 R Zone3 R Zone4 R Zone5 R Zone6 R Zone7 R Zone8 R 2-33 (E) VPL-FHZ131L...
  • Page 106 *4: In VPL-F1301ZL series, VPL-F1001 series and VPL-F901ZL series, the initial value is 50. *5: In VPL-F1301ZL series, VPL-F1001 series and VPL-F901ZL series, the initial value is “Simplified Chinese”. *6: In VPL-F1301ZL series, VPL-F1001 series and VPL-F901ZL series, the initial value is “OFF”. 2-34 (E) VPL-FHZ131L...
  • Page 107 B REG V G Panel LR DFT AUT HPC R RGT0 Read Data HPC G RGT0 Read Data HPC B RGT0 Read Data HPC R RGT1 Read Data HPC G RGT1 Read Data HPC B RGT1 Read Data 2-35 (E) VPL-FHZ131L...
  • Page 108 Fan 15 Target RPM Read Data Read Data Read Data Read Data RS 232C Parity RS 232C StopBits Disable Filter Cleanup Digital1 EQ Gain Digital2 EQ Gain HDBaseT Mode HDMI EQ Auto Enable Signal Delay Adjust VTCO On 2-36 (E) VPL-FHZ131L...
  • Page 109 Transmitter Version Read Data Link Status Read Data HDMI Status Read Data Protocol Emulation Status Protocol Emulation Mode Protocol Emulation Reset Other/CSC Filter Open/ Close Other/Forced Fan Setting *1: This item varies depending on the used model. 2-37 (E) VPL-FHZ131L...
  • Page 111 Therefore, specified parts should be used in the case of な部品です。したがって，交換する時は必ず指定 replacement. の部品を使ってください。 2. Standardization of Parts 2.  部品の共通化 Some repair parts supplied by Sony differ from those   ソニーから供給する補修用部品は，セットに使われて used for the unit. These are because of parts common- いるものと異なることがあります。 ality and improvement.
  • Page 112 Cover Block 3-2. Exploded Views BVTP BVTP 12 BVTP BVTP To B board VPL-FHZ131L...
  • Page 113 5-006-082-01 s LABEL (LENS), CAUTION (For White model) 5-006-082-11 s LABEL (LENS), CAUTION (For Black model) 4-577-920-02 s LABEL (LENS APERTURE) (For VPL-FHZ131L/FHZ101L/FHZ91L(White)) 4-577-920-12 s LABEL (LENS APERTURE) (For VPL-FHZ131L/FHZ101L/FHZ91L(Black)) 4-580-755-02 s LABEL (LENS APERTURE) (For VPL-F1301ZL/F1001ZL/F901ZL) 4-580-755-12 s LABEL (LENS APERTURE)
  • Page 114 C Board and MB Board : For VPL-FHZ131L/F1301ZL/F1306ZL MB Board (A side) CN300 CN102 (To light source (To CSC unit) unit) CN203 CN202 (To DC fan 7 and (To DC fan 5) DC fan 8) CN201 CN100 (To C board)
  • Page 115 2-650-770-11 s SLIDE, CLAMP 3-080-039-01 s CLAMP (FCR-15), FLAT 4-446-029-01 s GASKET (U4) 4-574-687-02 s SHEET (PD), RADIATION 4-741-536-01 s CUSHION HARNESS 4-743-776-01 s SHEET (30X30X3), RADIATION 4-743-777-01 s SHEET (20X20X3), RADIATION 4-745-221-01 s CUSHION (10X13X4) 7-682-948-01 s SCREW +PSW 3X8 VPL-FHZ131L...
  • Page 116 Fan Block BVTP BVTP To C board To MB board To MB board To C board BVTP To C board BVTP BVTP VPL-FHZ131L...
  • Page 117 4-741-537-01 s CUSHION (105), SIROCCO 4-741-538-01 s CUSHION (SENSOR) 4-741-539-01 s CUSHION SOLENOID 4-741-573-01 s SHEET,HOLDER PSC 4-744-770-01 s CUSHION, SIROCCO 7-682-948-01 s SCREW +PSW 3X8 7-682-951-01 s SCREW +PSW 3X14 7-682-957-01 s SCREW +PSW 3X40 7-685-648-79 s SCREW +BVTP 3X12 TYPE2 IT-3 VPL-FHZ131L...
  • Page 118 Light Source Unit and Fan Block 1 To B board : TAPE,ACETATE To NR board To MA board To MB board To ST board BVTP To Power unit (LD-PFC) To MB board To MB board BVTP To MB board To MA board BVTP VPL-FHZ131L...
  • Page 119 Light Source Unit and Fan Block 1 Part No. SP Description A-2227-199-A s LIGHT SOURCE UNIT (12K), S (For VPL-FHZ131L/F1301ZL/F1306ZL) A-2227-235-A s LIGHT SOURCE UNIT (9K), S (For VPL-FHZ101L/FHZ91L/F1001ZL/F1006ZL/F901ZL/F906ZL) 1-855-394-21 s DC FAN (80 SQUARE, SIROCCO) 1-855-434-11 s DC FAN (92 SQUARE)
  • Page 120 1-855-434-11 s DC FAN (92 SQUARE) 4-741-571-01 s MESH, FRONT FAN 1-972-345-11 s SUB HARNESS(C-FAN_14/15) 1-972-374-11 s SUB HARNESS(MB-SF) (For VPL-FHZ131L/F1301ZL/F1306ZL) 7-682-948-01 s SCREW +PSW 3X8 2-580-602-11 s SCREW, +PSW M4X12 7-685-648-79 s SCREW +BVTP 3X12 TYPE2 IT-3 2-580-603-11 s SCREW, +PSW M4X16...
  • Page 121 4-741-360-01 s SHEET, G 1-972-337-11 s SUB HARNESS(G-MA/C/Q) 4-741-361-01 s SHEET, LD 1-972-338-11 s SUB HARNESS(G-LD_PFC) 4-741-362-01 s SHEET, LD-HS 1-972-358-11 s SUB HARNESS (G/PFC-F) 1-972-360-11 s SUB HARNESS(LD_PFC-LD_2) 1-972-363-11 s SUB HARNESS (LD-LA) 7-682-948-01 s SCREW +PSW 3X8 3-11 VPL-FHZ131L...
  • Page 122 Power Unit 2 To C board BVTP To Power unit (LD-PFC) To Power unit (G) 3-12 VPL-FHZ131L...
  • Page 123 A-2224-006-A s QM MOUNT A-2224-011-B s ST MOUNT A-2224-012-A s MA MOUNT A-5016-033-A s QA COMPL H A-5016-035-A s B COMPL H (SYQ) (For VPL-FHZ131L) A-5016-036-A s B COMPL H (CN-W) (For VPL-F1301ZL) A-5016-039-A s B COMPL H (CN-B) (For VPL-F1306ZL)
  • Page 124 Bottom Cover Block To Power unit (F2) BVTP BVTP BVTP 3-14 VPL-FHZ131L...
  • Page 125 (For Black model) 4-741-540-01 s CUSHION LD DUCT BTM 7-682-548-04 s SCREW +B 3X8 7-682-948-01 s SCREW +PSW 3X8 7-682-961-01 s SCREW +PSW 4X8 7-685-647-71 s SCREW +BVTP 3X10 TYPE2 IT-3 7-685-648-79 s SCREW +BVTP 3X12 TYPE2 IT-3 3-15 VPL-FHZ131L...
  • Page 126 Optics Block To C board To C board To C board To C board To MB board 3-16 VPL-FHZ131L...
  • Page 127 Part No. SP Description A-2227-196-A s ILL UNIT ASSY, S A-2227-197-A s LENS SHIFT, S A-2227-198-B s PRISM ASSY(12K),S (For VPL-FHZ131L/F1301ZL/F1306ZL) A-2227-234-B s PRISM ASSY(9K),S (For VPL-FHZ101L/FHZ91L/F1001ZL/F1006ZL/F901ZL/F906ZL) A-2227-200-A s INPOL ASSY (R), S A-2227-201-A s INPOL ASSY (G), S A-2227-202-A s INPOL ASSY (B), S...
  • Page 128 1-848-212-15 s AC POWER SUPPLY CORD SET (For INDIA) 3-170-078-01 s HOLDER (B), PLUG 1pc *1 5-016-718-01 s PACK, CD-ROM (JAPANESE, ENGLISH, FRENCH, SPANISH, GERMAN, ITALIAN, ARABIC, RUSSIAN, CHINESE) *3 4-741-393-01 s COVER (ACC), TERMINAL *4 4-741-393-11 s COVER (ACC), TERMINAL 3-18 VPL-FHZ131L...
  • Page 129 X1300 CN1000 IC1001 XTAL USB_OTG USB SW Q1905 USB-B Q1002 B board MX_I2C CN1001 TOOL SW SW USB_SEL1 IC1003 Q1000 IC1201 SERIES_3.3V IC1200 USB SW USB_SEL0 UART 232C DRIVER CN1200 Q1006 USB_D_VBUS_PW SUB5V_Q 232C SEL PW_VBUS_SW RS-232C Overall (1/3) VPL-FHZ131L...
  • Page 130 SENSOR_PROT_B_ROB 3.3V_ERR (SUB3.3V) C101, C102 AC_OFF_DET W_FG EDLC AC_LH W_PWM_IN D100-D103 D100-D103 TH100 ROBSTER_RESET LD BANK LD BANK LD_UART_SEL NET_POWER_ON LAMP_UART RUBY_EN From TH100 TH100 QA board C board POWER_KEY KEY_0 KEY_1 LASER1_TEMP LASER2_TEMP THERMAL FUSE ECO_ON Overall (2/3) VPL-FHZ131L...
  • Page 131 GERONIMO_LVDS UNIF_R (7p airs) R_VSIG [1-48] (12P airs) P_CLK/HS/VS/DE (12P airs) I2C_PD TERRY VCOM_RVCS_R/PSIG_R CSC UNIT CTRL PANEL DRIVER PANEL IC701, IC702 For VPL-FHZ131L/F1301ZL/F1306ZL GCFB_R CTRL_R iCHIPS DDR2 2 X800 TG_R WARPING iPC-PRO XTAL LVDS Rx OSC MOTOR & IC1200...
  • Page 132 POWER_LED RUBY_LVDS_RCLK2- STBY_LED STBY_LED CN100 CN106 COVER_LED COVER_LED RUBY_LVDS_RCLK2+ LENS_PROT LENS_PROT RUBY_LVDS_RD2- VCC/N.C VCC/N.C CN203 RUBY_LVDS_RD2+ CN100 SUB3.3V SUB3.3V For VPL-FHZ131L/F1301ZL/F1306ZL SCL_100K_F SCL_100K_F RUBY_LVDS_RE2- SDA_100K_F SDA_100K_F CN102 RUBY_LVDS_RE2+ Free-fall_PROT FREE-FALL_PROT UNIT CSC_DRIVE+ CSC_Close(FilterON) SHOCK_DET SHOCK_DET CN100 CN107 SSPCLK CSC_DRIVE- CSC_Open(FilterOFF)
  • Page 133 EQ_CLKLOS_DVI EQ_CLKOS_DVI2 MX_I2C_SDA OPT_MOTOR_SEL0 UPDATE_MODE USB_SEL1 USB_SEL1 UPDATE_MODE MX_I2C_SCL EQ_CLKLOS_HDMI EQ_CLKOS_HDMI2 MX_I2C_SCL OPT_MOTOR_SEL1 UPDATE_COMPLETE USB_DP_PW 51-53 51-53 USB_DP_PW UPDATE_COMPLETE OPT_MOTOR_SEL2 135,136 X_HDMI_INT X_HDMI_INT 135,136 OPT_MOTOR_SEL3 ECO3.3V 137,138 USB_DM_PW USB_DM_PW 137,138 ECO3.3V Frame Wiring (2/2) 139,140 139,140 LENS_PROT 57-59 57-59 VPL-FHZ131L...
  • Page 135 Revision History Date History Contents 2020. 3 1st Edition ― 9-932-752-01 VPL-FHZ131L...
  • Page 137 .  QR コードは，株式会社デンソーウェーブの登録商標です。 .  NeoReader は NeoMedia Technologies Inc. の商標または登録商標です。 その他，記載されているシステム名，製品名は，一般に各開発メーカーの登録商標 あるいは商標です。 Trademarks Trademarks and registered trademarks used in this manual are as follows. .  Internet  Explorer  is  a  registered  trademarks  of  Microsoft  Corporation  in  the  United States and Other countries. .  Windows is a registered trademark of Microsoft Corporation in the United States  and Other countries. .  Safari is a registered trademark of Apple Corporation in the United States and/ or  other countries. .  Google Chrome is a trademark of Google LLC. .  QR Code is a registered trademark of DENSO WAVE INCORPORATED. URL: http://www.qrcode.com/faqpatent.html .  NeoReader is a trademark or registered trademark of NeoMedia Technologies Inc. Other system names, product names, and company names appearing in this manual  are trademarks or registered trademarks of their respective holders. VPL-FHZ131L...
  • Page 138 VPL-FHZ131L (SY) VPL-FHZ131L (IN) VPL-F1301ZL (CN) VPL-F1306ZL (CN) VPL-FHZ101L (SY) VPL-FHZ101L (IN) VPL-F1001ZL (CN) VPL-F1006ZL (CN) VPL-FHZ91L (SY) VPL-FHZ91L (IN) VPL-F901ZL (CN) Printed in Japan Sony Corporation VPL-F906ZL (CN) J, E 2020. 3 32 9-932-752-01 ©2020...

This manual is also suitable for:

Vpl-fhz101lVpl-fhz91lVpl-f1301zlVpl-f1306zlVpl-f1001zlVpl-f1006zl ... Show all