Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for VELECO ZT63
Summary of Contents for VELECO ZT63
- Page 1 ZT63 USER MANUAL (Invalid Carriage) veleco...
-
Page 2: Table Of Contents
However, due to the policy of continuous improvement 1.1 Outside elements of the scooter 4.1. Before driving of our products, Veleco reserves the right to make changes at any time. 1.2 Dashboard 4.2. Driving a scooter 1.3 Batteries ... -
Page 3: First Contact With The Scooter
1.1 Outside elements of the scooter Plate with the identification Front light (VIN/chassis) number Front indicator lights Ignition switch Front wheel Cup holder Footrest Charging socket Rear lights Rear storage box* Backrest* Seat Mirrors veleco veleco *depending on the model... -
Page 4: Dashboard
Drive mode switch (D - forward, R - reverse) (p. 26) Drive mode switch (I - II - III gear) (p. 26) Right handle Right brake lever Right mirror Parking brake* (p. 27) Brake fluid reservoir veleco veleco *depending on the model... -
Page 5: Batteries
2.5 Steering system 2.6 Mirrors 2.7 Seat The way the keys work LOCK Keys are used to start the engine, close and open storage compart- UNLOCK ments. TURN ON ALARM PRESS 2 TIMES TO TURN ON THE veleco veleco SCOOTER REMOTELY... - Page 6 In cold and humid climates, due ted near the lock and the tailgate ly closed after closing. to freezing, locks and door me- hook when closing it, as this may chanisms may not work properly. damage the latch. veleco veleco...
- Page 7 After turning the WARNING cause ignition of the battery. key to the left, the storage compartment will be blocked. Risk of injury - before charging veleco veleco remove the key.
- Page 8 2.5 Steering system Ignition switch Speedometer Left handlebar Right handlebar veleco veleco...
-
Page 9: A) Ignition Switch
In this position the key cannot be removed „OFF” POSITION • The scooter’s power is turned off. • The lights are turned off. • The key can be removed. POSITION „LOCK” • In this position, the steering wheel is locked veleco veleco... - Page 10 When switching on the high beam, the indicator lamp lights up. 64.0 Turn signals km/h When the direction indicator light is on, the left or right turning light flashes. Odometer 0000.0 Measure the distance traveled by a vehicle. veleco veleco...
-
Page 11: C) Left Handlebar
Switching on the main beam is only possible when the low beam is on! After switching on the low beam, press the switch down to activate the high beam as long as the button is held down PASSING veleco veleco... - Page 12 Turn signal switch WARNING Failure to use the turn signals or not to turn them off after the maneuver is complete can be very dangerous. Other road users may misjudge the driver’s intentions, which may result in an accident. When changing...
- Page 13 In this position and with the ignition switch in the ON position, the low beam is switched on In this switch position and with the ignition switch in the ON position, the side lights are switched on In this position, the scooter’s lights are turned off. veleco veleco...
-
Page 14: Mirrors
R position, by of 1-8 mph Before driving, make sure that the angle of the mirrors is set correctly. veleco veleco turning the grip the scooter (1-12 kmh) or when unlocked 1-16 mph ( for Europe ) For safety, clean the mirrors regularly. -
Page 15: Seat
• Make sure that the seats do not get wet. It may affect the structure of the skin. Some materials may cause discoloration on the surface of the seat upholstery. veleco veleco... - Page 16 7. Turn off the charger plug from the charging socket on the scooter. The scooter is ready for use again. WARNING Use only original batteries. Veleco is not responsible for any damage resulting from the Optimal battery charging is in use of batteries that have not the range of 20–80%.
- Page 17 Using lights will affect the battery consumption; therefore the range untainous areas can also we- of the vehicle is reduced accordingly. aken the ability to control the scooter. Remember to reduce speed and watch out for side veleco veleco winds.
- Page 18 It is very important to prevent the accumulation of mud, dust, ice etc. on the vehicle chassis. This unnecessary load can cause increased battery con- sumption and corrosion. • Do not overload the scooter. Unnecessary loads should not be transported. veleco veleco The load increases the battery consumption.
- Page 19 Reverse driving requires increased concentration and caution. Because of this, ger braking distances and can lead also. Keep a sufficient and safe ZT63’s speed during reverse movement compared to forward travel has been signifi- to collisions. Using only one of the bra- distance from vehicles in front cantly reduced.
- Page 20 The batteries cannot be charged. • The batteries are not properly matched. • The main switch on the housing is in the off position. • The charging socket is damaged. veleco veleco • Incorrect charger. • The charger is damaged.
- Page 21 31 st / 199 kg Air humidity for storage and use Model ZT63 The manufacturer reserves the right to make changes to technical parameters. Measurement tolerance ± 15 mm / 1.5 kg / °. Description * The theoretical value of the range is smaller if the scooter is often used on slopes...
- Page 22 • Moisture and dirt, for example with battery mud • Exploitation of the Good (in particular batteries) at low (i.e. below 0 degrees) temperatures. • Damage resulting from lack of due diligence regarding the maintenance of metal and chromium parts veleco veleco...
- Page 23 Use of a battery that is not in accordance with the intended use and recommendations of the manufacturer. j. Damage caused as a result of neglecting the technical condition of the vehicle. k. Damage resulting from the use of parts other than original offered by Veleco. veleco...
- Page 24 Preferred storage temperature: + 20 ° C). • Protect batteries from excessive discharging. Recharge the batteries fully. If you have additional questions, please consult your dealer who will be happy to help you with issues related to battery storage and servicing. veleco veleco...
- Page 25 Inspection by - 3 months, 9 months, 12 months, 18 months, 21 months from sales date. Periodic inspection for the ZT63 model You must inspect your scooter according to these standards to keep the warranty valid. Inspection NAME DATE ◆...
- Page 26 If necessary: checking the operation, first without load, then at ◆ ◆ ◆ ◆ ◆ rated load (safe working load) to check engines for wear or damage through veleco comparison of the electric current with the values obtained when the vehicle was delivered. ______________________ ______________________ ◆ ◆...
- Page 27 veleco...