Troubleshooting - Kenwood TS-930S Instruction Manual
Hide thumbs
Also See for TS-930S:
- Service manual (92 pages) ,
- Instruction manual (51 pages) ,
- Instruction manual (50 pages)
Table of Contents
Advertisement
Han tANEADCHEADD;
TRANSMITTER SECTION
SYMPTOM
No output in SSB (No Ic.)
VOX does not operate.
. Open microphone cable or bad
microphone
. Low microphone gain.
. PROC switch is to ON with PROC
IN/OUT control fully counterclockwise.
. VOX GAIN contro! too low.
VOX trips by speaker output.
Mic or radio chassis is ''hot'' during TX.
. ANT! VOX control requires adjustment.
Excess RF in the shack. No earth ground,
poor ground, or antenna is too close to
the radio.
Poor audio in SSB, TX-feedback.
Excess RF in the shack.
RECEIVER SECTION
SYMPTOM
Lights do not light and there is no receiver
noise when the POWER switch is turned
on.
An antenna is connected but no signals are
heard.
An antenna is connected but S-meter
deflects without a received signal.
SSB signal unintelligible.
SSB received signal is extremely high cut
CAUSE
1. Bad power cable or connections.
2. Blown power supply fuse.
Microphone PTT switch (or stand-by
switch) is in the transmit position.
1. RF GAIN control closed.
2. Low AC line voltage.
MODE switch is set to wrong sideband.
Slope tuning is out of adjustment.
stUHALeoCHSMDDoCLIELOseLaNEDoCHAANteCOLIDPAIEELOOMUDELe A LLTa AIRE rHRLEIDN ORL LN ¢R1 LESLEY ARAN OMAN AHL NTD ALTA oAL ED ALLEL D+ GELB oATANE DOME UNDO CRED OETA AEEEHoCEA NO CULL ES oeES RD LDI HDD A NED CED eed NELS~CELDEDWA UTES ONRES2 CURT DOMME EL DeGEELLIOCRLNM DHA LITDO ANE ENO oADELESADLATPOATED DoCED ISD OCELCDDOCH DANN CDA CED AADONEOLEETDS,
SECTION 9. TROUBLESHOOTING
TAUeEdreaNGDanoeDdEDDeCUETED ORNL AGEUEEoALRT=AINUb CEE oGAbLa yA ALAND oAENOLD ADU UOABEDNY = A2LgE8 AFI bo CLL TGA CHU TMOOU LTD CEU ABD OCRET DOC LNGoCEELA DOAN TEDD SUNROOM LBELS CETUS oCEDEEA OUMET=CUULE)=€088 B9o€TUUESeCUUED=ASLEDDoOADELDOCHLEDoCHUEED=ULDRIeGADINDomEULUDARELIDoSRRUD+OONLAPoC PER NeOH LAvedNgtSo<EELEn OCOD ¢ESNODOASERIDOSAINEOT
REMEDY
. Check the microphone.
. Increase the mic Gain.
. Increase the PROC IN/OUT settings.
. See section 5.4.7, VOX operation.
. See section 5.4.7, VOX operation.
ANTI VOX control requires adjustment.
See section 5.4.7, VOX operation
See section 3.8, 3.9.
See section 3.8, 3.9.
REMEDY
1. Check cables and connections.
2. Check for the cause of the blown fuse
and replace the fuse.
Release the PTT switch
1. Open RF GAIN control.
2. Use a step-up transformer to raise the
line voltage.
Turn MODE switch to the correct
sideband.
RIT control inoperative.
RIT switch is off.
Push RIT button.
Set to the NORMAL position.
or low cut.
38
Advertisement
Table of Contents
