Page 2 Photo CD is a trademark of Eastman Kodak. Sonic RecordNow! is a registered trademark of Sonic Solutions. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.LINK is trademark and registered trademark of Sony Corporation.
Page 3: Working Environment
This product and the supplied accessories are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if accessories or cables not manufactured / distributed by TOSHIBA are connected or implemented. To avoid EMC problems in general, the following advice should be observed: ■...
Page 4 Any consequences resulting from the use of this product in working environments that are not approved or the use is restricted are not the responsibility of TOSHIBA Corporation. The consequences of the use of this product in those working environments may be: ■...
Page 5 Description on Laser specification The optical drive, such as a DVD-ROM / CD-R/RW drive or DVD Super Multi drive, that is used in this computer is equipped with a laser device. A classification label with the following sentence is affixed to the surface of the drive.
Page 6 Preface Congratulations on your purchase of the PORTÉGÉ M400 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M400 computer.
Page 7: Manual Contents
Manual contents This manual is made up of the following. Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options. Chapter 2, The Grand briefly explains how they function. Chapter 3, Getting operating your computer and gives tips on safety and designing your work area.
Page 8 Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+).
Page 9 Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.
Page 10 PORTÉGÉ M400 User’s Manual...
Page 11: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 12 Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions. PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation.
Page 13: Table Of Contents
Table of Contents Preface General Precautions Introduction Chapter 1 Equipment checklist........1-1 Features.
Page 14 Replacing the battery pack ....... . 6-14 TOSHIBA Password Utility....... . . 6-16 Tablet mode.
Page 15 TOSHIBA support ........
Page 16 Certification agencies ........F-1 TOSHIBA Anti-theft Protection Timer...
Page 17: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 18 TOSHIBA Controls ■ TOSHIBA Mic Effect ■ TOSHIBA Password Utility ■ TOSHIBA Rotation Utility ■ TOSHIBA Accelerometer Utilities ■ TOSHIBA Tablet Access Code Logon Utility ■ Fingerprint utility ■ TOSHIBA Wireless Key Logon ■ Online manual ■ Product Recovery DVD-ROM Documentation ■...
Page 19: Features
Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in Some models in the range are equipped with Intel Technology, which is based on three separate technologies of Intel Core™...
Page 20 Power Battery pack Slice Expansion Battery Legal Footnote (Battery Life) For more information on the Legal Footnote regarding Battery Life, please refer to the Legal Footnotes section in Chapter 10. RTC battery AC adaptor Disks Hard disk drive Legal Footnote (Hard Disk Drive Capacity) For more information on the Legal Footnote regarding HDD Drive Capacity, please refer to the Legal Footnotes section in Chapter 10.
Page 21: Optical Media Drive
Optical media drive Computers in this series can be configured with an optical media drive installed in the Ultra Slim Bay. The available optical media drives are described below. DVD-ROM / CD-R/RW drive DVD Super Multi drive User’s Manual Some models are equipped with a full-size, DVD-ROM / CD-R/RW drive module that lets you run CD/DVDs without using an adaptor.
Page 22 DVD Super Multi drive Double Layer Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Legal Footnote (LCD) For more information on the Legal Footnote regarding LCD, please refer to the Legal Footnotes section in Chapter 10.
Page 23: Pointing Device
The computer has Universal Serial Bus ports that comply with the USB 2.0 standard. This port enables connection of an optional TOSHIBA Express Port Replicator described in Options section. This port enables high-speed data transfer directly from external devices such as digital video cameras.
Page 24 Communications Modem Bluetooth Wireless LAN User’s Manual An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia.
Page 25: Ultra Slim Bay
The Ultra Slim Bay is a single-drive bay that accommodates either a DVD-ROM / CD-R/RW drive, DVD Super Multi drive or a secondary hard disk drive. The TOSHIBA Mobile Extension utility enables the hot insertion of these modules when you are using a plug and play operating system.
Page 26: Special Features
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Cross Function button ESC/Rotation button Press this button for more than one second to Windows Security tablet button...
Page 27 You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver. When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation and shuts down.
Page 28 Optical Drive Power HDD Protection The HDD Protection function does not guarantee that the hard disk drive will not be damaged. Hibernation Standby User’s Manual Clicking on the Optical Drive Power icon in the taskbar will turn the power to the optical media drive on or off.
Page 29: Utilities
TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and the TOSHIBA Assist button (default setting is to launch the TOSHIBA Assist application) This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Page 30 InterVideo WinDVD. This software enables communication between remote Bluetooth devices. The TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system. You can access the TOSHIBA SD Memory Boot Utility from the menu bar by...
Page 31 TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to TOSHIBA TouchPad On/Off Utility TOSHIBA Mic Effect TOSHIBA RAID Utility TOSHIBA Password Utility TOSHIBA Accessibility DLA for TOSHIBA TOSHIBA Hotkey Utility for Display Devices TOSHIBA SD Memory Card Format User’s Manual allow easy control of communication devices and network connections.
Page 32 You can start TOSHIBA Accelerometer Utilities by clicking start, click All Programs, click TOSHIBA, click Tablet PC and Setup for TOSHIBA Accelerometer Utilities. If a Windows password has been set, you can logon to the operating system by entering a handwriting signature into the dialog box using the Tablet PC Pen when prompted.
Page 33: Options
AC adaptor for each site so you will not have to carry the adaptor with you. An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. This battery pack increases your computer's operating time when a main battery pack is also installed.
Page 34 Security lock User’s Manual Additional Reserve Pens can be purchased from your TOSHIBA dealer for use in the event the main pen becomes lost or damaged. The Reserve Pen is stored inside the computer. This drive is a DVD-ROM / CD-R/RW Drive that connects via one of the computer's USB ports.
Page 35 Ultra Slim Bay options The following modules can be installed in the Ultra Slim Bay. All other modules are options. Ultra Slim Bay Hard Disk Drive Adaptor Ultra Slim Bay DVD-ROM / CD-R/RW Drive Kit Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit Hard Disk Drive Kit (Serial-ATA)
Page 36: Chapter 2 The Grand Tour
The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Click the Front with the display closed The following figure shows the computer’s front with its LCD display panel in the closed position.
Page 37 ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
Page 38: Left Side
Left side The following figure shows the computer’s left side. Cooling vents Security lock slot Cooling vents Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Page 39: Right Side
i.LINK (IEEE1394) port Right side The following figure shows the computer’s right side. Tablet PC Pen Tablet PC Pen slot Tablet PC Pen Bridge media slot Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge Media Slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Page 40: Back Side
Back side The following figure shows the computer’s back side. DC IN 15V jack USB port DC IN 15V jack Universal Serial Bus (USB 2.0) port External monitor port Modem jack ■ Connection to any communication line other than an analog phone line could cause a PC system failure.
Page 41: Underside
LAN jack ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction. Link indicator (green) LAN active indicator...
Page 42 Slide the latch to release or secure the Ultra Slim Bay ejector. Notches on the computer engage hooks on the TOSHIBA Express Port Replicator to ensure a secure connection. The Reserve Pen is contained in the recess on the underside of the computer and enables data entry directly through display screen in addition to the main Tablet PC Pen.
Page 43: Front With The Display Open
(Left) Display hinge User’s Manual One screw secures the Ultra Slim Bay latch. This port enables connection of an optional TOSHIBA Express Port Replicator and a Slice Expansion Battery described in Chapter 8, Optional Devices. TOSHIBA Assist button Windows Security tablet...
Page 44 This button functions the same as the Ctrl + Alt + Del keys to show Windows Task Manager. Press this button to launch the TOSHIBA Assist utility (default) or some other predefined application.
Page 45 (Windows XP only). Pressing this button again changes to single display mode on the internal monitor only. You can specify the function of the TOSHIBA Presentation button in the TOSHIBA Controls properties. Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■...
Page 46: System Indicators
System indicators LEDs beneath icons, light when various computer operations are in progress. DC IN Power Battery Secondary battery Wireless communication User’s Manual System indicators The DC IN indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Page 47: Keyboard Indicators
Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 48: Usb Floppy Disk Drive (Optional)
USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. USB connector Disk-In-Use Indicator USB connector Disk-In-Use Indicator This indicator lights when the floppy disk is being Floppy disk slot Eject button Check the Disk-In-Use indicator when you use the USB floppy disk drive.
Page 49: Optical Media Drives
Optical media drives The computer is installed with either a DVD-ROM / CD-R/RW or a DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the media drives Region codes for DVD drives and media...
Page 50 Formats The drives support the following formats: ■ CD-ROM ■ DVD-ROM ■ CD-DA ■ Photo CD™ (single/multi-session) ■ CD-ROM XA Mode 2 (Form1, Form2) DVD-ROM / CD-R/RW drive The full-size DVD-ROM / CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
Page 51: Ac Adaptor
DVD Super Multi drive Double Layer The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 52 For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.
Page 53: Chapter 3 Getting Started
Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 54: General Conditions
PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.
Page 55 ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
Page 56: Seating And Posture
Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level Foot rest ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor.
Page 57: Work Habits
■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user. ■ Shield the PC from direct light by using tinted windows or by installing blinds or a screen.
Page 58: Operating The Computer In Tablet Mode
Operating the computer in Tablet mode Change to "The TOSHIBA PORTÉGÉ M400 computer can be used in two ways, as an ordinary laptop PC and as a Tablet PC. You can use the computer as Tablet PC, operated with the supplied Tablet PC Pen, by turning the LCD display panel through 180 degrees and closing it.
Page 59: Connecting The Ac Adaptor
■ Do not expose the computer to rapid temperature changes (such as would be the case if you brought the PC from a cold environment into a warm room). When rapid temperature changes are unavoidable, leave the computer for around two hours before turning it on to prevent the formation of condensation.
Page 60 ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 61 1. Connect the power cord to the AC adaptor. The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. 2.
Page 62: Opening The Display
Opening the display The computer’s LCD display panel can be opened in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly.
Page 63: Starting Up For The First Time
2. Slide and hold the computer’s power button. Power button Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.
Page 64: Standby Mode
■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, slide the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Page 65: Hibernation Mode
1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility located within the Control Panel application (open Performance and Maintenance and then open TOSHIBA Power Saver).
Page 66: Starting Hibernation Mode
For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
Page 67: Restarting The Computer
Restoring TOSHIBA utilities and drivers If Windows is working properly, individual drivers or applications can be separately restored. The TOSHIBA Tools & Utilities folder (C:\TOOLSCD) contains drivers and applications, which are included with your computer system. If your system drivers or applications have become damaged in some way, you can reinstall most of the components from this folder.
Page 68 Getting Started User’s Manual 3-16...
Page 69: Chapter 4 Operating Basics
Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Page 70: Using The Tablet Pc Pen And Reserve Pen
You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the Tablet PC Pen and Reserve Pen You can use the Tablet PC Pen to execute actions and enter data.
Page 71 Do not use a broken pen tip. The lead cannot be replaced if it is worn (use the Reserve Pen only). TOSHIBA is not liable for any problems arising on the products due to the use of the Tablet PC Pen in an environment where the above conditions are not satisfied or because of its use by unspecified number of users.
Page 72: Pen Actions
Removing the Tablet PC Pen Remove the Tablet PC Pen as described below. 1. Gently push the Tablet PC Pen towards the middle of the computer. The pen will then protrude slightly from the side. Tablet PC Pen slot 2. Pull the Tablet PC Pen to remove it from the Tablet PC Pen slot. Inserting the Tablet PC Pen The Tablet PC Pen is included in the accessory tray when purchased.
Page 73: Double Tap
LCD display panel. When the pen tip breaks replace it with one of the refills delivered with the Tablet PC Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer. User’s Manual...
Page 74: Removing The Reserve Pen Case
Removing the Reserve Pen case To remove the Reserve Pen case, follow the steps below. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4.
Page 75 Storing and Removing the Reserve Pen from the Reserve Pen case Follow the procedures below to remove the Reserve Pen from the Reserve Pen case. Removing the Reserve Pen from the Reserve Pen case 1. Lift the Reserve Pen up from the Reserve Pen case by its end. Reserve Pen case Storing the Reserve Pen in the Reserve Pen case 1.
Page 76: Changing To The Tablet Mode
To change from Laptop Mode to Tablet Mode you must rotate the display panel 180 degrees clockwise. Tablet mode icon To change from Tablet Mode to Laptop Mode you must rotate the display panel 180 degrees counter-clockwise. Laptop mode icon 1.
Page 77 2. Rotate the LCD display panel clockwise slowly. Do not apply excessive rotating force to the LCD display panel. It causes damage of the LCD display panel. 3. Turn the display latch 180 degrees to its down position. 4. Close the LCD display panel slowly with display surface facing upwards.
Page 78: Changing The Screen Orientation
6. Press the LCD display panel downward softly. Changing the screen orientation The orientation of the computer screen can be changed to one of the following four display modes: User’s Manual Changing to the Tablet mode (4) Primary portrait Primary landscape Four display modes Operating Basics Display latch...
Page 79: Accelerometer Utilities And Toshiba Rotation Utility
1. Press the Cross Function Button for more than one second. The TOSHIBA Tablet Menu will appear. 2. Select the Internal Monitor icon in Toshiba Shortcut using the Cross Function Button and then press then Cross Function Button. 3. Select the rotation angle using Cross Function Button and then press the Cross Function Button.
Page 80: Using Accelerometer Utilities
3. Select "changing the screen" from the Screen Orientation pull down menu and change the screen. You can set the orientation of the desktop screen just after rotating the display from [Start] - [All Programs] - [TOSHIBA] - [Tablet PC] - [TOSHIBA Rotation Utility]. Using Accelerometer Utilities When you shake the computer: ■...
Page 81: Changing To The Laptop Mode
It is safer if you hold the computer with both hands horizontally as shown in the below example. The computer is shaken Changing to the laptop mode To change the operating mode to the Laptop Mode, follow the instructions below. 1. Press the Display latch and raise the display to the upright position carefully.
Page 82 Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects.
Page 83 Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 84: Points To Note About The Fingerprint Utility
Align your fingertip with the sensor as shown in the drawing and Swipe Points to note about the Fingerprint Utility Backups for saved fingerprint data and saved information in the PasswordBank can be performed in Import or Export User Data under Fingerprint Software Management.
Page 85: Window Logon Via Fingerprint Authentication
You can also start User Enrollment Wizard using the following method. ■ Click the Protector Suite QL icon in the Task Bar. ■ Swipe your finger across the Fingerprint Sensor. 2. Click Next. 3. The User’s Password screen is displayed. Ensure the same Windows logon username is displayed before entering a password into the Enter your password field.
Page 86: How To Enable Fingerprint Power-On Security Settings
■ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
Page 87: Fingerprint Utility Limitations
TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 88: Using The Usb Floppy Disk Drive (Optional)
Laptop mode. While lightly touching the sensor, swipe the finger towards you when in portrait mode, and sideways when in either landscape mode or Laptop mode until the sensor surface becomes visible.
Page 89: Changing Ultra Slim Bay Modules
USB connector If you connect the USB floppy disk drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed. Disconnecting USB floppy disk drive When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it: 1.
Page 90: Removing A Module
The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, this utility to change modules while the computer’s power is on. Removing a module Remove the Ultra Slim Bay module as described below. 1. Wait for the indicator light to go out to make sure all disk activity has stopped.
Page 91: Using Optical Media Drives
Inserting a module Insert the Ultra Slim Bay Hard Disk Drive adaptor as described below. 1. Insert the Ultra Slim Bay Hard Disk Drive adaptor in the computer as shown below and press until the ejector mechanism clicks. 2. If you want to lock the Ultra Slim Bay Hard Disk Drive adaptor, place the Ultra Slim Bay lock screw in the hole for its lock position.
Page 92: Loading Discs
Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Pressing the eject button 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open User’s Manual...
Page 93 3. Lay the CD/DVD, label side up, in the disc tray. When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat.
Page 94: Removing Discs
If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button. Removing discs To remove the CD/DVD, follow the steps below. Do not press the eject button while the computer is accessing the media drive.
Page 95: Writing Cds On Dvd-Rom / Cd-R/Rw Drive
How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Page 96: Before Writing Or Rewriting
RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW mdeia is affected by the quality of the disc and the way it is used.
Page 97: Writing Cd/Dvds On Dvd Super Multi Drive
When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■...
Page 98: Important Message
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 99 DVD-R DL: (Double Layer supported model only) MITSUBISHI CHEMICAL CORPORATION DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: (Double Layer supported model only) MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION...
Page 100 ■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and DVD-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive. ■...
Page 101: When Writing Or Rewriting
Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...
Page 102: Data Verification
■ RecordNow! cannot record in packet format. ■ You might not be able to use the "Exact Copy" function of RecordNow! to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder. ■...
Page 103: Dla For Toshiba
DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. ■ DLA does not support formatting and writing to a DVD-RAM disc - these functions are performed by DVD-RAM Driver Software.
Page 104: Important Information For Use
How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click [Start] - [All Programs] - [InterVideo WinDVD Creator2] - [InterVideo WinDVD Creator] to launch WinDVD Creator. 2. Click [Capture] button then capture the video data from the DV-Camcorder via IEEE1394.
Page 105 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Page 106: Media Care
Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 107: Sound System
8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields.
Page 108: Audio Power Management
For more instructions for this software, click start, point to All Programs, point to TOSHIBA, point to Utilities and click TOSHIBA Mic Effect Help. User’s Manual 4-40...
Page 109: Modem
Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 110: Properties Menu
Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region.
Page 111 ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...
Page 112: Wireless Communications
Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner. Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices.
Page 113: Worldwide Operation
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology (optional) Bluetooth™...
Page 114: Product Support
Please refer also to the electronic information which is included with each software. This Bluetooth™ Stack is based on the Bluetooth™ Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth™ other than TOSHIBA mobile computers.
Page 115: Wireless Communication Switch
Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■...
Page 116: Lan
The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Page 117: Cleaning The Computer
1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN jack 3.
Page 118: Moving The Computer
Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it is recommended that you change the function of the HDD Protection. Refer to the section, Disk Drive (HDD) ■...
Page 119: Using The Hard Disk Drive (Hdd) Protection
Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on the hard disk drive. Using an acceleration sensor built into the computer, HDD Protection detects vibration, shocks and similar signs of movement of the computer, and automatically moves the hard disk drive head to a safe position to reduce the risk of damage that could be caused by head-to-disk contact.
Page 120: Toshiba Hdd Protection Properties
Operating Basics TOSHIBA HDD Protection Properties You can change the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection Setting.
Page 121: Heat Dispersal
Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Page 122: Chapter 5 The Keyboard
The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 123: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 124: Hot Keys
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay operate these keys.
Page 125 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters Standby Mode.
Page 126 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 127: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an "F number" key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 128: Windows Special Keys
Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 129: Numeric Mode
Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys. Press Fn + F11 again to turn off the overlay. Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1.
Page 130: Generating Ascii Characters
Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 131: Chapter 6 Power And Power-Up Modes
Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
Page 132 Secondary adaptor battery fully connected charged Secondary battery partially charged or no charge No Secondary battery installed Main battery adaptor charge is above low battery connected trigger point Main battery charge is below low battery trigger point Main battery charge is exhausted No main battery installed...
Page 133 When the main battery is not charging. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a Slice Expansion battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 134: Power Indicators
Power indicators As shown in the above table, the Battery, Secondary battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the Secondary battery indicator to determine the status of the Slice Expansion battery.
Page 135: Battery Types
Power indicator Check the Power indicator to determine the power status: Green Flashing orange No light Battery types The computer has three types of batteries: ■ Battery pack ■ Slice Expansion Battery (optional) ■ Real Time Clock (RTC) battery Battery pack When the AC adaptor is not connected, the computer’s main power source is a removable lithium ion battery pack, also referred to in this manual as the main battery.
Page 136 The Slice Expansion Battery is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. User’s Manual Power and Power-Up Modes...
Page 137: Care And Use Of The Battery Pack
Chapter 9 Troubleshooting, for details. The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 138 3. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or a fire, and could also damage the battery pack. Always wrap the battery pack in plastic (or place it in a plastic bag) whenever transporting it, to avoid exposing the terminals to another conductive object which could result in serious injury.
Page 139 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely. If the battery falls out, while you are carrying the PC, you could be injured or the battery pack could be damaged.
Page 140: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 141: Battery Charging Notice
Time The following table shows the approximate time required to fully charge a discharged battery. Battery type Battery pack (4700mAh) Slice Expansion Battery (4000mAh) RTC battery The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Page 142: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 143: Retaining Data With Power Off
Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery type Battery pack (4700mAh) Slice Expansion Battery (4000mAh) RTC battery Extending battery life To maximize the life of your battery pack: ■...
Page 144: Replacing The Battery Pack
Replacing the battery pack The battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Page 145 6. Slide the battery release latch to free the battery pack for removal, then slide out the battery pack. To install a battery pack, follow the steps below. Do not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch.
Page 146: Toshiba Password Utility
TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in the TOSHIBA Password Utility are different from the Windows password. User Password To start the utility, point to or click the following items: start ->...
Page 147 ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your HDD, or for any other losses to you or any other person or organization that result from the loss of access to your HDD.
Page 148: Supervisor Password
Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.
Page 149: Tablet Mode
The beep sounds when tapping the on-screen keyboard with the Tablet PC Pen. An * (asterisk) is displayed after " character is input for every tapping. Register your password to the computer in the laptop mode using the standard keyboard. Refer to the detail.
Page 150: Panel Power On/Off
Panel power on/off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power will be turned on in Standby Mode or Hibernation Mode but not in boot mode. If the panel power off function is enabled and you manually shut down Windows, do not close the computer’s LCD display panel until the shut down process has been completed.
Page 151: Chapter 7 Hw Setup
HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 152 General This window displays the BIOS version and contains two buttons: Default and About. Default About Setup This field displays Display This tab lets you customize your computer’s display settings for either the internal LCD screen or an external monitor. Power On Display Lets you select the display to be used when the computer is booted (This setting is only available on Standard VGA mode and is not available on...
Page 153: Boot Priority
Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: −> −> CD-ROM −> −> CD-ROM −> CD-ROM −> −> CD-ROM −> −> CD-ROM −> −> CD-ROM −> You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: The floppy disk drive will be used to start the computer when there is a bootable disk contained in the external drive.
Page 154 To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
Page 155 HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD 1 ->...
Page 156 USB Memory BIOS Support Type Set the type of the USB memory as a startup device. Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Standby mode.
Page 157: Device Config
Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Disabled Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
Page 158: Configuring The Execute-Disable Bit Capability And Tpm
■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the configuration through the BIOS setup program, please be aware that the configuration set through the Windows applications will take priority.
Page 159: Ending The Bios Setup Program
Select either the Execute-Disable Bit Capability or settings in the security controller to make changes. Please refer to the operating instructions displayed in the settings screen. Ending the BIOS Setup Program Save the changes and end the program. 1. Press the End Key. Are you sure? (Y/N) The changes you made The "...
Page 160: Security Controller
Available Not Available System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. LCD Display Stretch Select the display function of the LCD.
Page 161: Diagnostic Mode
■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
Page 162: Chapter 8 Optional Devices
Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ Bridge media slot ■ SD card (SD memory card, SDIO card) ■...
Page 163: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 164: Bridge Media Slot
Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped.
Page 165: Memory Card Care
Media care Observe the following precautions when handling the card. Card care ■ Do not twist or bend cards. ■ Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. ■ Do not touch the metal part of a card or expose it to liquids or let it get dirty.
Page 166: Removing An Sd Card
2. Press gently to ensure a firm connection. ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below.
Page 167: Sd Memory Card
TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Page 168: Write Protection
Write protection Memory Stick can be write protected to safeguard your data. To write- protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position. Inserting a Memory Stick To insert a Memory Stick, follow the steps below. 1.
Page 169: Xd Picture Card
xD picture card The computer is equipped with a Bridge media slot that can accommodate xD picture cards with various memory capacities. The xD picture card let you easily transfer data from devices, such as digital cameras that use xD picture card flash-memory.
Page 170: Memory Expansion
When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following...
Page 171: Installing A Memory Module
Installing a memory module There are slots for two memory modules. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the 2.
Page 172 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest.
Page 173 10. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot.
Page 174: Removing A Memory Module
Do not bend the keyboard ribbon cable. 13. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard.
Page 175: Battery Pack
6. Grasp the sides of the module and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.
Page 176: Slice Expansion Battery
Slice Expansion Battery This battery pack increases your computer's operating time when a main battery pack is also installed. For details on using the battery pack, follow the steps below. Connecting the Slice Expansion Battery Follow the steps below to connect the Slice Expansion Battery to the computer When handling Slice Expansion Battery, be careful not to short circuit the terminals.
Page 177: Disconnecting The Slice Expansion Battery
Optional Devices Disconnecting the Slice Expansion Battery Follow the steps below to disconnect the Slice Expansion Battery to the computer. 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3. Remove all cables connected to the computer. 4.
Page 178: Battery Charger
Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). HDD Kit (Serial-ATA) An extra hard disk drive expands the flexibility of your system and lets you carry your data without carrying the computer.
Page 179 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Plastic tab Installing the HDD Kit (Serial-ATA) To install the HDD Kit (Serial-ATA), follow the steps below. 1. Move the connector until it is vertical. 2.
Page 180: Ultra Slim Bay Hdd Adaptor
Ultra Slim Bay HDD Adaptor You can increase your computer’s data storage capacity by installing an additional 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Ultra Slim Bay. To install a hard disk drive in the Ultra Slim Bay HDD adaptor follow the steps below.
Page 181: Usb Fdd Kit
3. Close the lid and slide the lock to the lock position. For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, USB FDD Kit The USB FDD Kit module can be connected to a USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Basics.
Page 182: Video Modes
External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports XGA and SXGA+ video modes. To connect a monitor, follow the steps below. 1. Turn the computer’s power off. 2. Connect the monitor cable to the external monitor port and tighten the screws on the left and right hand side.
Page 183 There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 184: Toshiba Express Port Replicator
Refer also to the documentation that came with your i.LINK device. TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source.
Page 185: Security Lock
Security lock Security locks enable you to anchor your computer and optional TOSHIBA Express Port Replicator to a desk or other heavy object to help prevent unauthorized removal of the computer or TOSHIBA Express Port Replicator. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.
Page 186: Troubleshooting
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 187: Preliminary Checklist
Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 188: Hardware And System Checklist
Hardware Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 189: System Start-Up
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 190: Overheating Power Down
Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Standby Mode and shut down. Problem Computer shuts down and DC IN indicator blinks orange It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking.
Page 191 If you frequently recharge a partially charged battery, the battery might not charge to its full potential. Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. Troubleshooting...
Page 192: Real Time Clock
5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Procedure Refer to the TOSHIBA Password Utility Chapter 6, Power and Power-Up Modes. Keyboard. Procedure Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.
Page 193: Internal Lcd Display Panel
Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Problem No display Markings appear on the LCD screen. Problems above remain unresolved or other problems occur Hard disk drive Problem Computer does not boot from hard disk drive Slow performance...
Page 194: Dvd-Rom&Cd-R/Rw Drive
DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Problem You cannot access a CD/DVD in the drive Some CD/DVDs run correctly, but others do User’s Manual Operating Procedure Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on.
Page 195: Dvd Super Multi Drive
User’s Manual Procedure If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 196 USB floppy disk drive (optional) For more information, refer to Chapter 4, Problem Drive does not operate There may be a faulty cable connection. Check Some programs run correctly but others do You cannot access the external 3 1/2" floppy disk drive PC card Refer also to Chapter 8,...
Page 197 SD card Refer also to Chapter 8, Problem SD card error occurs You cannot write to an SD memory card You cannot read a file Memory Stick/Memory Stick Pro Refer also to Chapter 8, Problem Memory Stick/Memory Stick Pro error occurs You cannot write to an Memory Stick/Memory Stick Pro...
Page 198: Touch Pad
Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem On-screen pointer does not respond to Pad operation Double-tapping does not work The mouse pointer moves too fast or too slow The reaction of Touch...
Page 199: Usb Mouse
USB mouse Problem On-screen pointer does not respond to mouse operation Double-clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erratically Fingerprint Sensor Problem Reading of the fingerprint was not successful. The fingerprint cannot be read due to injuries to the finger.
Page 200: Usb Device
USB device Refer also to your USB device’s documentation. Problem USB device does not work Memory expansion Refer also to Chapter 8, memory modules. Problem Beep sounds. (Two beeps, a dash and a dot, for a defective memory module in slot A. Three beeps, a dash and two dots for slot B.
Page 201 Sound system Refer also to documentation for your audio devices. Problem No sound is heard Annoying sound is heard External monitor Refer also to Chapter 8, documentation. Problem Monitor does not turn No display Display error occurs User’s Manual Procedure Adjust the volume control dial.
Page 202 i.LINK (IEEE1394) device Problem i.LINK device does not function Modem Problem Communication software can’t initialize modem You can hear a dial tone but can’t make a call You place a call, but a connection can’t be made After making a call you can’t hear a ring Communication is cut off unexpectedly...
Page 203 Problem You cannot receive an incoming call Problem Cannot access LAN Wake-up on LAN does not work Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Problem...
Page 204: Disposing Of Pc And Pc Batteries
Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government. ■ This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
Page 205: Toshiba Support
TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 206: Chapter 10 Legal Footnotes
Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual.
Page 207: Memory (Main System)*2
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 208: Lcd*5
Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Page 209: Specifications
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) Size User’s Manual Appendix A 2.18 kilograms, configured with: 12.1"XGA, 512MB RAM, 40GB HDD, DVD-ROM&CD-R/RW drive, modem, LAN, Wireless LAN, 6cell battery pack, Table PC Pen. Weight will vary with other configurations. Above weights are measured at specific criteria.
Page 210: Power Requirements
Environmental Requirements Conditions Operating Non-operating Thermal Gradient Wet-bulb temperature Conditions Operating Non-operating Power Requirements AC adaptor Computer Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing Control command Monitor function Communication specifications Communication system User’s Manual Ambient temperature 5°C (41°F) to 35°C (95°F)
Page 211 Network control unit (NCU) Communication protocol Communication speed Transmitting level Receiving level Input/output impedance Error correcting Data compression Power supply User’s Manual Data ITU-T-Rec V.21/V.22/V.22bis/V.32 (Former CCITT) V.32bis/V.34/V.90 Bell 103/212A ITU-T-Rec V.17/V.29/V.27ter (Former CCITT) V.21 ch2 Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps...
Page 212: Display Controller And Modes
Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. Two models are available: ■...
Page 213 Video mode Type 0, 1 VGA Text 2, 3 VGA Text 0*, 1* VGA Text 2*, 3* VGA Text 0+, 1+ VGA Text 2+, 3+ VGA Text 4, 5 VGA Grph VGA Grph VGA Text VGA Text User’s Manual Table: Video modes (VGA) Resolution Character matrix...
Page 214 Table: Video modes (VGA) continued Video mode Type VGA Grph 320 × 200 Pels VGA Grph 640 × 200 Pels VGA Grph 640 × 350 Pels VGA Grph 640 × 350 Pels VGA Grph 640 × 480 Pels VGA Grph 640 × 480 Pels VGA Grph 320 ×...
Page 215 Table: Video modes (XGA model) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 216 Table: Video modes (XGA model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 217 Table: Video modes (XGA model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with LCD only) 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 218 Table: Video modes (SXGA+ model) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 219 Table: Video modes (SXGA+ model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 220 Table: Video modes (SXGA+ model) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 1400 × 1050 1600 × 1200 (Virtual with LCD only) 1920 × 1440 (Virtual with LCD only) 2048 × 1536 (Virtual with LCD only) * Only External Monitor can perform change of Vertical frequency (Hz).
Page 221: Wireless Lan
Wireless LAN Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol Data Rate User’s Manual Appendix C PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Page 222: Radio Characteristics
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 223 Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
Page 224 Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range Channel ID User’s Manual Wireless LAN 5150-5850 MHz 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825...
Page 225: Toshiba Raid
Please refer to the TOSHIBA RAID help for details. ■ By changing this setting you are reconfiguring your hard disk.
Page 226: Windows Manual Setup
F6 key. 3. When the message " following mass storage device(s): screen, press the S key and install the TOSHIBA RAID Driver using the TOSHIBA RAID Driver Disk that was created. 4. Follow the onscreen instructions to continue Windows setup.
Page 227 An effective way to ensure that such situations do not happen is to carry out RAID-1 media checks regularly. The TOSHIBA RAID utility is set as default to carry out media checks every month on the third Wednesday from noon.
Page 228: Starting, Modifying And Ending The Bios Setup Program
RAID-1 UNKNOWN No Drive User’s Manual is displayed, enter the User Password and press the TOSHIBA Password Shows the current hard disk status. Modify the hard disk configuration. (Modifications are made with this setting). Status of the connected hard disk.
Page 229 2. Press the Y key. The configured settings are saved and the BIOS setup program ends. The computer may reboot depending on the settings that were modified. User’s Manual TOSHIBA RAID " message is displayed.
Page 230: Appendix E Bluetooth Wireless Technology Interoperability
Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
Page 231 TOSHIBA portable computers. Always use Bluetooth™ Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm...
Page 232: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 233: Ac Power Cord And Connectors
AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size:...
Page 234 Finland: France: Germany: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S.
Page 235: Toshiba Anti-Theft Protection Timer
BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
Page 236: If Your Computer Is Stolen
What is your address, phone, and fax number? To register the theft on paper, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) below. ■ Attach a copy of your receipt showing where your computer was purchased.
Page 237: Toshiba Theft Registration
To register the theft online, please follow these procedures: ■ Visit www.toshiba-europe.com on the Internet. In the product area, choose Computer Systems. ■ In the Computer Systems page, open the Support & Downloads menu and choose the Stolen Units Database option.
Page 238 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 239 Glossary IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock...
Page 240 adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices.
Page 241 bit: Derived from "binary digit," the basic unit of information used by the computer. It is either zero or one. Eight bits is one byte. See also byte. board: A circuit board. An internal card containing electronic components, called chips, which perform a specific function or increase the capabilities of the system.
Page 242 CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable. cold start: Starting a computer that is currently off (turning on the power). COM1, COM2, COM3 and COM4: The names assigned to the serial and communication ports.
Page 243 data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve. data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters.
Page 244 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. User’s Manual...
Page 245 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 246 instruction: Statements or commands that specify how to perform a particular task. interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another. 2) To physically connect one system or device to another to exchange information.
Page 247 LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip. 2) An integrated circuit that uses large scale integration. main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte.
Page 248 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 249 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
Page 250 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 251 warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication.
Page 252 10 brightness decrease 5 brightness increase 5 controller 1 hinge 8 opening 10 screen 9 DLA for TOSHIBA 15, 35 Docking interface 7, 8 Documentation list 2 DVD Super Multi drive 5 location 4 problems 10 using 23...
Page 253 Fingerprint Sensor location 8 problems 14 using 13 Floppy disk care 38 Fn + Ctrl (enhanced keyboard simulation) 3 Fn + Enter 3 Fn + Esc (sound mute) 3 Fn + F1 (instant security) 4 Fn + F10 (Arrow mode) 3 Fn + F11 (Numeric mode) 3 Fn + F12 (ScrLock) 3 Fn + F2 (power save mode) 4...
Page 254 Modem 17 Overheating power down 5 Password 7 PC card 11 Pointing device 13 Power 4 Real Time Clock 7 SD card 12 Self test 4 Sound system 16 System start-up 4 TOSHIBA support 20 USB 15 PORTÉGÉ M400 Index-3...
Page 255 System automatic 10 TOSHIBA Assist 14 TOSHIBA Assist button 10 TOSHIBA ConfigFree 15 TOSHIBA Controls 13 TOSHIBA Express Port Replicator 17, 23 TOSHIBA Mic Effect 15 TOSHIBA Mobile Extension 14 User’s Manual TOSHIBA PC Diagnostic Tool 14 TOSHIBA Power Saver 13...

This manual is also suitable for:

Portege m400-144 Portege m400-3g145 Portege m400-156 Portege m400-170

Toshiba Portege M400 User Manual

Table of Contents

Chapter 1 Introduction

Chapter 2 The Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Chapter 10 Legal Footnotes

Appendix A Specifications

Appendix B Display Controller and Modes

Appendix C Wireless LAN

Appendix D TOSHIBA RAID

Appendix E Bluetooth Wireless Technology Interoperability

Appendix F AC Power Cord and Connectors

Appendix G TOSHIBA Anti-Theft Protection Timer

Pointing Device

Quick Links

Chapters

Related Manuals for Toshiba Portege M400

Summary of Contents for Toshiba Portege M400