Table of Contents
Advertisement
GB
MENU OPERATION
Language is used to select the preferred language . Use the 1 or
2 button to select English, French, German, Italian, Spanish or
Dutch .
H-Position changes the OSD position horizontally by using the 1
or 2 button .
V-Position changes the OSD position vertically by using the 1 or
2 button .
Duration is used to set the display time of the MENU by using the
1 or 2 button . (5 ~ 120 seconds)
Transparence is used to adjust transparence of menu display . Use
the 1 or 2 button to adjust levels .
n PIP/POP Setup
Use the 5 or 6 button to select PIP/POP Setup and press the
1 or 2 button to enter the sub menu .
PIP/POP Mode: Using the 1 or 2 button select the most suit-
able mode PIP1, PIP2, POP or Off . (Please refer to page 13 .)
✐ When Mode is set to Off, Sub Source and PIP Position will not
work .
Main Source is used to select input source (AV1, RGB, AV2, AV3, PC,
DVI or Network ) for main picture by using the 1 or 2 button .
Sub Source is used to select input source (AV1, AV2, AV3, PC or
DVI) for sub picture by using the 1 or 2 button .
✐ For a combination of main picture and sub picture: only DVI or
Network input can assemble with other input source . For example,
if main source is selected as AV1 input, then the sub source must
be DVI or Network input .
PIP Position: Using the 1 or 2 button it can be selected Top
Left, Top Right, Bottom Right or Bottom Left .
n Initial Settings
This function returns all setting values except for Installation Mode .
n Text Language
Use the 5 or 6 button to select Text Language and press the
1 or 2 button to select Western, Eastern, Russian, Arabic or
Farsi .
n Tile Mode
This function allows you to split an image to suit your monitor grid
format to create a video wall .
Use the 5 or 6 button to select Tile Mode and press the 1 or
2 button to enter the sub menu as follows .
Tile Mode Active can be set On or Off using the 1 or 2 button .
H_Sets is used to divide the horizonal picture into more than one
part, but the most is 5 parts (5 monitors) .
10
V_Sets is used to divide the vertical picture into more than one part,
and the most is also 5 parts (5 monitors) . Using the 1 or 2
button to set .
H Location is used to select one part of the horizonal picture to dis-
play on the current LCD Monitor using the 1 or 2 button .
V Location is used to select one part of the vertical picture to display
on the current LCD Monitor using the 1 or 2 button .
Bezel H Adjustment is used to align the image horizontally with re-
spect to the other monitors in the video wall to accomodate the bezel
width using the 1 or 2 button . (0 ~ 10)
Bezel V Adjustment is used to align the image vertically with respect
to the other monitors in the video wall to accomodate the bezel width
using the 1 or 2 button . (0 ~ 10)
n AV2 Setting
Use the 5 or 6 button to select AV2 Setting and press the 1
or 2 button to select YPbPr or RGBHV .
Connect your PC to either PC-IN or RGBHV on the rear of the set .
Once connected select PC mode or AV2 (RGBHV, see page 5 for AV2
input settings) via the INPUT button on your remote control .
The set will become a monitor for the PC .
n Native Resolution
Use the 5 or 6 button to select Native Resolution and press the
1 or 2 button to select XGA or WXGA 1366 x 768 .
n PC Power Save
The monitor set automatically turns off with no PC input signal and
wakes up with signal while PC Power Save is active .
Use the 5 or 6 button to select PC Power Save and press the
1 or 2 button to select ON or OFF .
PC Adj. menu
Press the MENU button and select PC Adj. using the 5 or 6 but-
tons, press the 1 or 2 button to enter . Press the BACK button
to return to the previous menu . Press the MENU button to exit menu
operation .
Auto Adjust is used to automatically detect incoming signal, and
adjust itself to optimize its performance by using the 1 or 2
button . If the image is not displayed properly, a manual adjustment is
required (Refer to following adjustments) .
H-Position is used to move the horizontal picture position by using
the 1 or 2 button .
V-Position is used to move the vertical picture position by using the
1 or 2 button .
Clock is used to eliminate flicker from the image by using the 1 or
2 button .
Phase is used to eliminate disorder from the image by using the 1
or 2 button .
GB
Advertisement
Table of Contents
