Siemens RUGGEDCOM i803 Installation Manual
Rugged ethernet switches
Hide thumbs
Also See for RUGGEDCOM i803:
- Installation manual (36 pages) ,
- Installation manual (28 pages)
Related Manuals for Siemens RUGGEDCOM i803
Summary of Contents for Siemens RUGGEDCOM i803
- Page 1 Edition 04/2022 Installation Manual SIMATIC NET Rugged Ethernet Switches RUGGEDCOM i803 https://www.siemens.com/ruggedcom...
- Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged Ethernet Switches RUGGEDCOM i803 Communication Ports Technical Specifications Installation Manual Certification 04/2022 C79000-G8976-1005-07...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Accessing Documentation ....................... v Registered Trademarks ......................v Warranty ..........................vi Training ..........................vi Customer Support ........................vi Contacting Siemens ....................... vii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 3 Decommissioning and Disposal ................4 Supported Fiber Optic Cables ................ - Page 5 FCC ........................27 6.1.5 FDA/CDRH ......................27 6.1.6 ISED ........................28 6.1.7 ISO ........................28 6.1.8 ACMA ........................28 6.1.9 RoHS ........................28 6.1.10 Other Approvals ....................29 EMC and Environmental Type Tests ..............29 RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 6: Preface
Preface This guide describes the RUGGEDCOM i803 (i-Series) product line. It describes the major features, installation, commissioning and important technical specifications. It is intended for use by network technical support personnel who are responsible for the installation, commissioning and maintenance of the device. It is also recommended for use by network and system planners, system programmers, and line technicians. -
Page 7: Warranty
Preface Warranty Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. -
Page 8: Contacting Siemens
Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile App Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: •... - Page 9 Preface Contacting Siemens viii RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 10: Introduction
Gigabit Ethernet. With up to nine Ethernet ports, the RUGGEDCOM i803 is the perfect choice for a wide variety of demanding industrial environments such as those found in process control applications (oil and gas, petro-chemical, metals and mining, wind farms). -
Page 11: Description
Compression fit connections • CSA/UL 60950 safety approved to 85 °C (185 °F) Description The RUGGEDCOM i803 features various ports, controls and indicator LEDs on the front panel for connecting, configuring and troubleshooting the device. Failsafe Alarm Relay Power Supply Terminal Block... -
Page 12: Required Tools And Materials
"Connecting to the Device (Page 13)". Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM i803: Tools/Materials Purpose AC or DC power cord (16 AWG) For connecting power to the device. -
Page 13: Decommissioning And Disposal
1000Base-SX 10GBase-SR OM1 (62.5/125) — 1300 2000 — — OM2 (50/125) — 1300 2000 — — OM3 (50/125) 1500 — 1300 2000 — — OM4 (50/125) 3500 — 1300 2000 — — Laser optimized. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07... -
Page 14: Installing The Device
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. -
Page 15: General Procedure
If any item is missing or damaged, contact Siemens for assistance. Mounting the Device The RUGGEDCOM i803 can be ordered with a DIN rail adapter pre-installed on the back of the chassis. Use the adapter to latch the mount the device to a standard 35 mm (1.4 in) by 15 mm (0.6 in) IEC/EN 60715 or TS35 DIN rail. - Page 16 Insert a flathead screw driver into the slot of the sliding release and move it down. Push the device against the bottom of the DIN rail, then let go of the sliding release to latch the device. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 17: Connecting The Failsafe Alarm Relay (If Equipped)
NO contact and closes the NC (Normally Closed) contact. Note Control of the failsafe relay output is configurable through RUGGEDCOM i803. One common application for this relay is to signal an alarm if a power failure occurs. For more information, refer to the "RUGGEDCOM ROS Configuration Manual"... -
Page 18: Connecting Power
Figure 2.3 Failsafe Alarm Relay Wiring Connecting Power The RUGGEDCOM i803 supports a single low DC power supply with reverse polarity and dual independent inputs. This allows for two redundant DC power sources with the same nominal voltage to be connected. - Page 19 GND Terminal Chassis Ground Terminal Figure 2.4 Terminal Block Wiring – Single DC Power Supply Input Connect the negative wire from the power source to the negative terminal (P1- or P2-) on the terminal block. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
- Page 20 2, making sure to connect the power supply to the P2 ports. Positive Terminal Negative Terminal GND Terminal Chassis Ground Terminal Figure 2.5 Terminal Block Wiring – Dual DC Power Supply Inputs Connect the chassis ground terminal to protective Earth. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
- Page 21 Installing the Device 2.5 Connecting Power RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 22: Device Management
"RUGGEDCOM ROS Configuration Manual" for the RUGGEDCOM i803. RS232 Console Port Connect a PC or terminal directly to the RS232 console port to access the boot- time control and RUGGEDCOM i803 interfaces. The console port provides access to RUGGEDCOM i803's console and Web interfaces. NOTICE The console port is intended to be used only as a temporary connection during initial configuration or troubleshooting. -
Page 23: Configuring The Device
Communication Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM i803 console and Web interfaces via the device's IP address. For more information about available ports, refer to "Communication Ports (Page 17)". - Page 24 MicroSD/MicroSDHC Card Figure 3.2 Inserting/Removing a MicroSD/MicroSDHC Card Without touching the contacts on the card, insert or remove the microSD/ microSDHC card. Install the access plate and finger-tighten the retention screw. Power up the device. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
- Page 25 Device Management 3.3 Inserting/Removing the MicroSD/MicroSDHC Card RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 26: Communication Ports
To determine which ports are equipped on the device, refer to the factory data file available through RUGGEDCOM i803. For more information on how to access the factory data file, refer to the "RUGGEDCOM ROS Configuration Manual"... -
Page 27: Fiber Optic Ethernet Ports
Fiber Optic Ethernet Ports Fiber optic Ethernet ports are available with LC (Lucent Connector) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07... - Page 28 Communication Ports 4.2 Fiber Optic Ethernet Ports Tx Connector Rx Connector Figure 4.3 LC Port For specifications on the available fiber optic Ethernet ports, refer to "Fiber Optic Ethernet Port Specifications (Page 22)". RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
- Page 29 Communication Ports 4.2 Fiber Optic Ethernet Ports RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 30: Technical Specifications
1 minute 220 VDC 0.24 A, 60 W 250 VAC 0.25 A, 62.5 W Copper Ethernet Port Specifications The following details the specifications for copper Ethernet ports that can be ordered with the RUGGEDCOM i803. Cable Wiring Maximum Speed Connector Duplex... -
Page 31: Fiber Optic Ethernet Port Specifications
3 dBm. To convert from peak to average, subtract 3 dBm. • Maximum segment length is greatly dependent on factors such as fiber quality, and the number of patches and splices. Consult a Siemens sales associate when determining maximum segment distances. Fixed Fast Ethernet Transceivers... -
Page 32: Mechanical Specifications
1.0 kg (2.2 lbs) Ingress Protection IP40 (1 mm or 0.04 in objects) Enclosure Cast Aluminum Enclosure Dimension Drawings Note All dimensions are in millimeters, unless otherwise stated. 11.7 77.5 95.3 99.5 56.5 Figure 5.1 Overall Dimensions RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07... - Page 33 Technical Specifications 5.7 Dimension Drawings RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
-
Page 34: Certification
Certification The RUGGEDCOM i803 device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. Approvals This section details the standards to which the RUGGEDCOM i803 complies. 6.1.1 This device meets the requirements of the following Canadian Standards Association... -
Page 35: 6.1.2 Atex/Iec Ex
• 12-24 VDC, 2A, Class III 6.1.3 European Union (EU) This device is declared by Siemens Canada Ltd. to comply with essential requirements and other relevant provisions of the following EU directives: • EN 61000-6-2 Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments •... -
Page 36: Fcc
Methods of Measurement The device is marked with a CE marking and can be used throughout the European community. A copy of the EU Declaration of Conformity is available via Siemens Industry Online Support at https://support.industry.siemens.com/cs/ww/en/view/109475424. 6.1.4 This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 37: Ised
Certification 6.1.6 ISED 6.1.6 ISED This device is declared by Siemens Canada Ltd. to meet the requirements of the following ISED (Innovation Science and Economic Development Canada) standard: • CAN ICES-3 (A)/NMB-3 (A) 6.1.7 This device was designed and manufactured using a certified ISO (International... -
Page 38: 6.1.10 Other Approvals
• IEC 61000-6-2 Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity for Industrial Environments EMC and Environmental Type Tests The RUGGEDCOM i803 has passed the following EMC and environmental tests. IEC 61850-3 Type Tests Test Description Test Levels... - Page 39 IEC 60068-2-30 Humidity (Damp Test Db 95% (non-condensing), Heat, Cyclic) 55 °C (131 °F), 6 cycles IEC 60068-2-6 Vibration 1 g @ 10-500 Hz IEC 60068-2-27 Shock 30 g @ 11 ms RUGGEDCOM i803 Installation Manual, 04/2022, C79000-G8976-1005-07...
- Page 40 For more information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens Canada Ltd. Digital Industries Process Automation 300 Applewood Crescent Concord, Ontario, L4K 4E5 Canada © 2022 Siemens Canada Ltd. Subject to change...