Page 1
All manuals and user guides at all-guides.com HISTORY Model Name KDL-26/32/37U4000 SERVICE MANUAL Click on Page Number to display detail of changes. Date Part Number Description of Revisions Version 2008.08 9-883-406-01 Original Manual.
Page 2
All manuals and user guides at all-guides.com SE2AG SERVICE MANUAL CHASSIS MODEL DEST KDL-26U4000 OIRT / UK / WE KDL-32U4000 OIRT / UK / WE KDL-37U4000 OIRT / UK / WE RM-ED009 FLAT PANEL COLOR TV - 1 -...
COMPONENTS IDENTIFIED BY SHADING AND MARKED THE EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. - 2 -...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
All manuals and user guides at all-guides.com SPECIFICATIONS Television System Channel Coverage Colour/Video System Analogue: Analogue: 48.25 - 855.25 MHz Analogue: Depending on your country/region PAL, SECAM B/G/H, D/K, L, I NTSC 3.58/4.43 (Video in only) Digital: Digital: VHF/UHF Digital: DVB-T/DVB-C MPEG-2 MP@ML LCD(Liquid Crystal Display) Panel...
All manuals and user guides at all-guides.com CONNECTORS 21 Pin Connector (SCART) Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A...
Page 7
All manuals and user guides at all-guides.com HDMI Connector Pin No Signal Assignment Pin No Signal Assignment TMDS Data2+ TMDS Clock Shield TMDS Data2 Shield TMDS Clock- TMDS Data2- TMDS Data1+ Reserved (N.C. on device) TMDS Data1 Shield TMDS Data1- TMDS Data0+ DDC/CEC Ground TMDS Data0 Shield...
Page 8
All manuals and user guides at all-guides.com SE2AG SELF DIAGNOSTIC SOFTWARE The identification of errors within the SE2AG chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
All manuals and user guides at all-guides.com SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal 2-2. Stand Removal => = > => = > => => To remove the ‘Rear cover’ remove the 22 fixing screws indicated To remove the ‘Stand’ remove the 3 fixing screws indicated. and pull the rear cover gently backwards away from the TV set.
All manuals and user guides at all-guides.com 2-5. BC1 Board Removal 2-6. GA2 Board Removal (26/32 inches) Screws Screws To remove the ‘BC1’ board disconnect all connectors and then remove To remove the ‘GA2’ board disconnect all connectors and then remove the 6 screws circled and ease the board gently away from the back of the the 4 screws circled and ease the board gently away from the back of the TV set.
All manuals and user guides at all-guides.com SECTION 3 ADJUSTMENTS 3-1. How to enter the Service Mode Service adjustments to this model can be performed using the supplied remote commander RM-ED009. BACKLIGHT BACKLIGHT (0, 255) U BACKLIGHT (0, 10) Turn on the power to the TV set and enter into the stand-by BL SETUDEN (0, 255) mode.
Page 12
All manuals and user guides at all-guides.com SOUND PANEL TEMP TEMP LM75 (0, 125) Lineout offset (-80, +40) TEMP ADC (0, 125) (0, 511) (-128, -1) (+0, +127) (+0, +127) (-128, -1) (0, 1023) Effect Mode (+0, +2) BBE Mode (-0, +127) BBE Vol main (+0, +255)
All manuals and user guides at all-guides.com 3-2. TT MODES TT mode is available by setting the TV for operation in Service Mode [ As shown on Page 10 ] , OSD ‘TT’ appears. The functions described below are available by selecting the two numbers. To release the ‘Test mode 2’, press 00, 10, 20 ... twice or switch the TV set into Stand-by mode.
All manuals and user guides at all-guides.com 3-3. TT OSD Labels T T - " E C S C B A N o r m (20) (25) D D C (21) (10) (11) (12) (22) (26) (13) (14) (15) (16) (17) (18) (19)
Page 15
All manuals and user guides at all-guides.com...
Page 16
All manuals and user guides at all-guides.com 4-2. CIRCUIT BOARD LOCATION 5-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM : SOLID FPRD : NON FLAMMABLE CARBON FUSE : NON FLAMMABLE FUSIBLE : NON FLAMMABLE METAL OXIDE : NON FLAMMABLE CEMENT : NON FLAMMABLE WIREWOUND CVM Board S1 Board...
Page 17
All manuals and user guides at all-guides.com FE_+2V5_DDR FE_+2V5 FL7104 FL7102 FL7103 THESE CAPACITORS TO BE PLACED UNDERNEATH BGA THESE CAPACITORS TO BE PLACED UNDERNEATH BGA FE_+1V5 C7116 C7102 C7114 C7112 4 . 7 E5 E17 F5 F17 G5 G17 T17 U5 U6 U17 E8 E9 E10 E11 E12 E13 E6 E7 E14 E15 E16 H5 H17 J5 J17 K5...
Page 18
All manuals and user guides at all-guides.com...
Page 19
All manuals and user guides at all-guides.com...
Page 20
All manuals and user guides at all-guides.com...
Page 21
All manuals and user guides at all-guides.com...
Page 22
All manuals and user guides at all-guides.com S1 S2 S3 G S1 S2 S3 G...
Page 23
All manuals and user guides at all-guides.com...
Page 24
All manuals and user guides at all-guides.com...
Page 25
All manuals and user guides at all-guides.com...
Page 26
All manuals and user guides at all-guides.com...
Page 27
All manuals and user guides at all-guides.com...
Page 28
All manuals and user guides at all-guides.com...
Page 29
All manuals and user guides at all-guides.com...
Page 30
All manuals and user guides at all-guides.com...
Page 31
All manuals and user guides at all-guides.com...
Page 32
All manuals and user guides at all-guides.com...
Page 33
All manuals and user guides at all-guides.com A-1545-604-A...
Page 34
All manuals and user guides at all-guides.com A-1556-XXX-A I C 7 3 0 I C 7 3 0 3 I C 7 3 1 0 I C 7 3 0 7 I C 7 3 0 6 I C 6 4 0 3 I C 5 5 0 W 1 7 5 I C 7 3 0 4...
Page 35
All manuals and user guides at all-guides.com 3 V 3 3 V 3...
Page 36
All manuals and user guides at all-guides.com E T 6 5 0 0 E T 6 5 0 2 3 V 3 3 V 3 C 6 5 1 0 C 6 5 0 9 E Y 6 5 0 4 E Y 6 6 1 2 E Y 6 6 1 1 R 6 6 0 0...
Page 37
All manuals and user guides at all-guides.com E Y 6 6 2 3 E T 6 6 0 1 J W 6 6 1 1 J W 6 3 2 5 E Y 6 6 2 6 J W 6 3 2 6 C 6 4 2 2 D 6 6 0 7 E Y 6 6 1 9...
Page 38
All manuals and user guides at all-guides.com...
All manuals and user guides at all-guides.com SECTION 5 EXPLODED VIEWS NOTE : Non-serviceable items with no part number and no Items marked “*” are not stocked description are not stocked because they are not since they are seldom required for required for routine service.
....................58 Note: To ensure safety and reliability it is Sony policy that power supply boards should not be repaired at component level in the field as a result... The GA2 and GA3 boards are regarded as non service items for...
Page 43
All manuals and user guides at all-guides.com Note : The components identified by mark contain confidential information. Strictly follow the instructions when ever the components are repaired and/or replaced. REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK C2072 1-100-916-11 CERAMIC CHIP 0.1UF A-1599-690-A BC1 Board, Complete C2073 1-100-916-11...