Page 1
WIRELESS CAMERA TRANSMITTER WLL-CA50 MAINTENANCE MANUAL 1st Edition Serial No. 100001 and Higher: WLL-CA50 (UC) Serial No. 300001 and Higher: WLL-CA50 (J) Serial No. 400001 and Higher: WLL-CA50 (CE)
Page 2
Gooi de batterij niet weg maar lever deze in als klein leer” oder nach längerer Gebrauchsdauer der Batterien chemisch afval (KCA). “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. WLL-CA50...
Page 3
For more information regarding recycling of re- chargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/ Caution: Do not handle damaged or leaking Nickel Metal Hydride batteries. 1 (P) WLL-CA50...
Manual Structure Purpose of this manual This manual is the maintenance manual for Wireless Camera Transmitter WLL-CA50. This manual is intended for use by the trained system enginneers and service enginneers, and describes information (service overview, electrical alignment, parts lists, schematic diagram and board layout) on the premise of component level service.
Block Diagrams Contains the block diagrams of overall and each circuit board. Section 6 Schematic Diagrams Contains schematic diagrams for every circuit board and frame wiring. Section 7 Board Layouts Contains board layouts for every circuit board. 6 (E) WLL-CA50...
GND for UNREG +12 V UNREG +12 V DC 10.5 to 17 V BATT IN (5P MALE) (External view) Signal Specifications BATTERY GND GND for BATTERY IN BATT ID DET BATT REW LIGHT CONT BATTERY IN DC 10.5 to 17 V 1-1 (E) WLL-CA50...
Parts Tool : Special screwdriver (T10) SW-1128 board (Sony Part No.: 3-985-911-01) 1. Loosen the six special screws with stopper using the special screwdriver (T10), and open the R panel Cord with connector assembly and L panel assembly.
FPGA, and is input to the MPEG encoder module. When the UNREG +12 V is not detected, the CH 1&2 digital audio signal of the group 1 in the SDI signal is input to the MPEG encoder module. 1-3 (E) WLL-CA50...
9.14 MHz whose band is restricted in BPF (IC401, 402). Then, the signal is upconverted into the set The power of the WLL-CA50 is supplied from the follow- frequency (2.4 GHz band), and is sent with the nondirec- ing connectors.
(blue) facing upward, and insert it in the direction of *1 : arrow A. 2. Close the connector latch in the direction of arrow B to Ref. No. Destination lock it. Reserved S2-1 Connector Connector latch S2-2 Flexible card wire Insulated surface (Blue) 1-5 (E) WLL-CA50...
2. Pull out the DPR-231 board and IF-914 board. Never reform the flexible card wire after being folded once. SW-1128 board CN2 5 5 EL display DPR-231 board 15 mm EL display SW-1128 board (CN2) Insulated surface (Blue) Insulated IF-914 board surface (Blue) 1-6 (E) WLL-CA50...
Page 17
Hold the plug to remove. 7. Remove the three screws, and remove the spacer. Do not atempt to remove by pulling the cable. CN11 Spacer M2 x 4.5 CN11 M2 x 4.5 Harness (CAMERA) P2 x 3 1-7 (E) WLL-CA50...
Page 18
Be careful not to bend the flexible card wires. This shortens the wire life. PS-645 board Hold the plug to Do not atempt to remove. remove by pulling P2.6 x 4 the cable. P2.6 x 4 Transmitter PS-645 board 1-8 (E) WLL-CA50...
When connecting the coaxial cable, hold the plug and connect the coaxial cable to the connector vertically. Press the plug into the connector by small turning to the left and the right. Hold the plug to connect Connecting connector 1-9 (E) WLL-CA50...
Board name Setting (Section to be referred to) IF-914 board Serial No setting (Section 1-14) MB-998 board Setting S2-1 and S2-2 on the MB-998 board (Section 1-6) EL display Timer reset (Section 1-15) 1-10 (E) WLL-CA50...
3. Turn on the power of this unit. used. Start the Download Tool software and read the Project . The PLD internal data is controlled in the Sony Database file. Server under the name Project file (E_xxx_xxx_xx_xx). 4. Program the PLD (or ROM for PLD) with the Down- .
LOAD side. Equipment IF-914 board . AC adaptor AC-550/550CE, AC-DN2B, or battery pack BP-L60A/L40A/M50/M100/IL75 . Extension board EX-819 : (Sony part No. : A-8327-481-A) . ROM-28 board : (Sony part No. : A-8326-017-A) DOWN Preparation LOAD Save the updating program in the ROMs H (IC2) and L (IC3) on the ROM-28 board.
. AC adaptor AC-550/550CE, AC-DN2B, or battery pack 4. Press the MENU knob. The sub menu of “Serial No.” BP-L60A/L40A/M50/M100/IL75 is displayed. . Extension board EX-819 : (Sony Part No. : A-8327-481-A) . ROM-28 board : (Sony Part No. : A-8326-017-A) Serial No. Preparation...
4. Set the cursor to “EL Timer” by turning the MENU . AC adaptor AC-550/550CE, AC-DN2B, or battery pack knob. BP-L60A/L40A/M50/M100/IL75 . Extension board EX-819 : (Sony Part No. : A-8327-481-A) Default Set : . ROM-28 board : (Sony Part No. : A-8326-017-A) Guard Interval :...
1-16. Optional Fixtures Fig. No. Name Sony part No. Remarks Screwdriver, special (T10) 3-985-911-01 To tighten the special screws. (Refer to Section 1-3.) ROM-28 board A-8326-017-A For updating the software. (Refer to Section 1-13.) Extension board EX-819 A-8327-481-A Extending the DPR-231/IF-914 board. (Refer to Section 1-13.)
Ref. No. Address Equipment protected If using a new flexible card wire, hand form it referring to THP1 Equipment connected to DC IN Section 1-7-2. connector . Flexible card wire (Sony Part No.: 1-827-252-11) 1-16 (E) WLL-CA50...
Therefore, specified parts should be used in the case of replacement. Hold the plug to connect 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- Connecting connector ality and improvement.
1. Set the DC LINE switch of the unit to OFF, and extend Extension board EX-819 the DPR-231 board using the EX-819 board. (Refer to (Sony Part No. : A-8327-481-A) the steps 1 to 3 of Section 1-13.) Measuring Equipment If the comcorder is connected to the unit, set the power .
3-601-846-01 s RING,O (NBR) 3-604-795-01 s CAP BNC 7-621-771-06 s SCREW +B2X5 3-612-444-01 s TYPE1,AROCK PRECISION +P2.6X6 7-621-772-08 s SCREW +B2X3 3-669-117-61 s WASHER,MOTOR (STEEL) 7-621-772-48 s SCREW +B2X8 3-669-596-00 s WASHER,2.3 (PLA) 7-627-556-38 s SCREW,PRECISION +P2.6X4 7-682-558-09 s SCREW +B4X4(EP-FE/ZNBK/CM2) WLL-CA50...
Page 32
1-761-664-11 s PWB, MOUNTED C BOARD 7-621-772-08 s SCREW +B2X3 1-962-232-11 s HARNESS (CAMERA) 7-621-772-48 s SCREW +B2X8 3-181-132-01 o SUPPORT 7-627-556-38 s SCREW,PRECISION +P2.6X4 3-370-749-01 s SCREW (M2X0.4), PRECISION 7-682-947-01 s SCREW +PSW 3X6 3-612-444-01 s TYPE1,AROCK PRECISION +P2.6X6 7-685-535-19 s SCREW,+BTP2.6X10(EP-FE/ZNBK/CM WLL-CA50...
Page 33
3-742-074-01 s SCREW (3X6) (ST) 3-612-444-01 s TYPE1,AROCK PRECISION +P2.6X6 3-679-669-05 o SPACER 3-679-688-02 o LEVER,RELEASE 3-679-690-02 o MOUNT, V (FRAME) 7-621-770-87 s SCREW +B2.6X5 7-627-553-38 s SCREW,PRECISION +P 2X3 3-680-269-01 s RUBBER (DO), DROP PROTECTION 7-627-556-38 s SCREW,PRECISION +P2.6X4 WLL-CA50...
1-100-276-21 s CAP, ELECT 22MF (5.0X6.5) C129 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C130 1-104-607-11 s CAPACITOR ELECT 47MF/16V(105C) C131 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C132 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C133 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C134 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V WLL-CA50...
Page 35
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C659 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C309 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C660 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C310 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C311 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V D101 8-719-036-83 o DIODE RD4.3SB-T1 WLL-CA50...
Page 36
1-469-555-21 s INDUCTOR, CHIP 10UH (LB2016) R149 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) L104 1-469-555-21 s INDUCTOR, CHIP 10UH (LB2016) R150 1-218-973-11 s RESISTOR,CHIP 47K 1/16W (1005) L105 1-414-836-21 s INDUCTOR, CHIP 4.7NH (1005) R151 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) WLL-CA50...
Page 37
1-208-643-11 s RESISTOR CHIP 22 1/16W (1005) R410 1-208-687-11 s RESISTOR CHIP 1.5K 1/16W (1005 RV101 1-225-789-21 s RES, ADJ, CERMET 2K R411 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) R412 1-218-945-11 s RESISTOR,CHIP 220 1/16W(1005) S201 1-692-271-31 s SWITCH, SLIDE WLL-CA50...
Page 38
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C145 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C146 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C147 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C148 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C149 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C150 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V WLL-CA50...
Page 39
1-208-935-11 s RESISTOR, CHIP 100K (1005) IC122 8-759-082-58 s IC TC7W08FU R127 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) IC123 8-759-594-71 s IC TC7SH14FU-TE85R R128 1-208-707-11 s RESISTOR,CHIP 10K 1/16W (1005) IC124 8-759-599-93 s IC NC7SZ08P5 R129 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) WLL-CA50...
Page 40
1-234-381-21 s RES, NETWORK 100KX4 (1005) R220 1-208-635-11 s RESISTOR CHIP 10 1/16W (1005) R222 1-218-953-11 s RESISTOR, CHIP 1K 1/16W S101 1-771-709-31 s SWITCH, SLIDE R223 1-218-953-11 s RESISTOR, CHIP 1K 1/16W S102 1-692-270-41 s SWITCH, SLIDE 3-10 WLL-CA50...
Page 41
1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-208-635-11 s RESISTOR CHIP 10 1/16W (1005) 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 3-11 WLL-CA50...
Page 42
1-127-738-11 s CAPACITOR, CERAMIC 4.7MF/25V C219 1-128-536-11 s CAPACITOR ERECT 100MF/25V(CHIP C220 1-127-738-11 s CAPACITOR, CERAMIC 4.7MF/25V C221 1-128-536-11 s CAPACITOR ERECT 100MF/25V(CHIP C222 1-135-343-11 s CAPACITOR,SOLID ELECT 120MF C223 1-127-738-11 s CAPACITOR, CERAMIC 4.7MF/25V C224 1-128-536-11 s CAPACITOR ERECT 100MF/25V(CHIP 3-12 WLL-CA50...
Page 43
1-424-700-21 s COIL, CHOKE (SMD) 100UH 8-719-066-68 s DIODE DSM3MA1-T L303 1-424-700-21 s COIL, CHOKE (SMD) 100UH 8-719-066-68 s DIODE DSM3MA1-T L304 1-416-344-11 s COIL, CHOKE 10UH 8-719-037-41 s DIODE RD20SB-T1 8-719-069-28 s DIODE 1SS400TE61 L305 1-416-344-11 s COIL, CHOKE 10UH 3-13 WLL-CA50...
Page 44
1-208-927-11 s RESISTOR, CHIP 47K 1/16W(1005) R322 1-208-711-11 s RESISTOR CHIP 15K 1/16W (1005) R100 1-218-977-11 s RESISTOR,CHIP 100K 1/16W(1005) R323 1-208-707-11 s RESISTOR,CHIP 10K 1/16W (1005) R101 1-208-715-11 s RESISTOR,CHIP 22K 1/16W (1005) R324 1-208-707-11 s RESISTOR,CHIP 10K 1/16W (1005) 3-14 WLL-CA50...
Page 45
1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-218-941-81 s C-RES,V 100-1/16W J 1-553-856-00 s SWITCH,KEY BOARD 1-570-995-11 s SWITCH, KEY BOARD 3-15 WLL-CA50...
1-695-215-11 o TERMINAL,SOLDERLESS (BATTERY OUT CONNECTOR) CN003 1-774-841-11 s CONNECTOR, BATTERY HN013 - - - HARNESS, SUB (POWER SW) (TO CN2/SW-1130 BOARD) 1-764-193-11 o HOUSING, CONNECTOR 3P 2pcs 1-695-215-11 o TERMINAL,SOLDERLESS (DC LINE SWITCH) S001 1-554-366-00 s SWITCH,TOGGLE 3-16 WLL-CA50...
1-754-281-11 s ANTENNA TX 2.4GHZ 3-742-686-01 s OPERATION MANUAL 3-748-115-01 s PACK,CD-ROM 3-5. Tools and Fixtures Part No. SP Description 3-985-911-01 s SCREW DRIVER,SPECIAL (T10) A-8326-017-A s MOUNTED CIRCUIT BOARD, ROM-28 A-8327-481-A o MOUNTED CIRCUIT BOARD, EX-819 J-7120-140-A o PLD DOWNLOAD JIG 3-17 WLL-CA50...
Page 49
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
+3.3V +3.3V, +2.5V +2.5V +2.5V IC201 +5V, +1.8V +1.8V +1.8V POWER ON IC301 DC OUT +9V, -5V DC IN UNREG 12V UNREG(AUDIO) UNREG OUT UNREG IN BATT OUT DC-124 BOARD BATT IN FOR CAMCORDER BATTERY Overall LOT NO. 323- WLL-CA50...
Page 54
1-22 CCLK GENLOCK DONE XTAL VCO 1-21 DONE PLL REF 27MHz 27MHz CLK STC 5V IC4,5,7,9 1-87 CPU BUS CPU BUS BUFF 1-130 CPU DATA 0-15 1-87 CPU ADDRESS 0-15 IF BOARD DPR-231 CPU CONTROL 1-130 LOT NO. 323- WLL-CA50...