hit counter script
Sony DVP-NC650V Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. DVD Player
  5. DVP-NC650V
  6. Service manual
Sony DVP-NC650V Service Manual

Sony DVP-NC650V Service Manual

Sacd/dvd player
Hide thumbs Also See for DVP-NC650V:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Sony DVP-NC650V

Summary of Contents for Sony DVP-NC650V

  • Page 2 Specifications and design are subject to change without notice. DIGITAL OUT Optical output jack -18 dBm Wave length 660 nm (OPTICAL) TAR  is a U.S. registered mark. As an TAR  Partner, Sony Corporation has determined NERGY NERGY DIGITAL OUT Phono jack 0.5 Vp-p 75 ohms terminated TAR ...
  • Page 3 OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS Section Title Page Section Title Page Service Note ................4 MB-101 (DSD DSP) Schematic Diagram ..... 4-35 AV-60 Printed Wiring Board .......... 4-37 GENERAL AV-60 (VIDEO BUFFER) Schematic Diagram ....4-39 AV-60 (MUTE) Schematic Diagram ......4-41 AV-60 (AUDIO AMP) Schematic Diagram ....

  • Page 5: Service Note

    SERVICE NOTE 1. DISASSEMBLY • This set can be disassembled in the order shown below. Upper case (Page 2-1) Reinforcement (C) block (Page 2-1) Front panel section Rear panel block (Page 2-1) (Page 2-1) Pewer block AV-60 board MB-101 board (Page 2-4) (Page 2-2) (Page 2-2)
  • Page 6 2. NOTE ON REMOVE THE UPPER CASE 4. NOTE ON MOUNTING GEARS 1) Remove seven tapping screws. (See Fig. 1) 1) Mount the gear (U/D). (See Fig. 3.) 2) Open the side of case. (See Fig. 1) 2) Rotate the gear (U/D) in the direction of arrow. 3) Remove the upper case as lift in the direction of arrow.
  • Page 7 6) Mount the lock lever (See Fig. 5.) 5. HOW TO SERVICE MB-101 BOARD 7) Mount the spring (lock lever). (See Fig. 5.) • Use the service jig (J-6090-107-A). 1) Remove the upper case from the set. (Refer to 2-1) Spring Lock lever (lock lever)
  • Page 8 7) Set two flexible flat cables as shown in Fig. 9. 9) Set the rear panel block as shown in Fig. 11. 5 Four screws (B3) 4 Bracket Rear panel block (CP) 2 Connector (CN105) 3 Three step Harness 2 Optical pick-up screws (AM-129A) block...
  • Page 9 6. CONNECTION OF SERVICE JIG AV-60 CN105 CN201 CN102 FFC 26P FFC 13P HARNESS 9P (Used the set) (Used the set) CN601 CN501 CN102 FFC 26P CN203 MB-101 Mechanism deck FFC 9P CN204 CN201 CN101 FFC 26P (Used the set) FFC 9P CN301 CN301...

  • Page 10: Index To Parts And Controls

    DVP-NC650V SECTION 1 This section is extracted from instruction GENERAL manual (3-070-514-11). • A disc recorded in a color system other than VIDEO CD Notes about the Discs About this Manual NTSC, such as PAL or SECAM. (This player conforms to the NTSC color system.)

  • Page 11: Guide To The Control Menu Display

    A TV/DVD switch (73) Rear Panel Remote B Z OPEN/CLOSE (open/close) button (33) C Number buttons (37) The number 5 button has a tactile dot. D CLEAR (clear) button (41, 43, 44, 45) E SACD MULTI/2CH (SACD multi/2- channel) button (38) F SACD/CD button (38) G AUDIO (audio) button (56) H ANGLE (angle) button (63)

  • Page 12: Getting Started

    VIEWER (page 50) Divides the screen into 9 sub-screens to help you find the scene you want quickly. Getting Started Each time you press DISPLAY, the Control Menu display changes as follows: Quick Overview Control Menu display 1 Control Menu display 2 A quick overview presented in this chapter will give you enough information to start using the ADVANCED display (Appears if you select any setting other than “OFF.”...

  • Page 13: Hookups

    A If you are connecting to a video input jack Hookups Connect the yellow plugs of the audio/video cord (supplied) to the yellow (video) jacks. You will enjoy standard quality images. Hooking Up the Player Yellow (Video) Yellow Follow Steps 1 to 4 to hook up and adjust the settings of the player. White (L) White (L) Before you start, turn off the power, check that you have all of the supplied accessories, and insert...
  • Page 14 SACD/DVD player Connecting to an AV amplifier (having 5.1ch input jacks or a digital input jack) and 4 to 6 speakers If your AV amplifier (receiver) has 5.1 channel inputs, use If you want to use the Dolby Digital or DTS decoder function on your AV amplifier (receiver), connect to its digital jack using .
  • Page 15 Connecting to a Dolby Surround (Pro Logic) decoder amplifier (receiver) and SACD/DVD player 3 to 6 speakers This connection will allow you to enjoy the surround effects of the Dolby Surround (Pro Logic) decoder on your amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital or DTS decoder, refer to page 22.

  • Page 16: Playing Discs

    J Press X/x to select the item. N Press X/x to select the size of the center speaker. Choose the item that matches the audio connection you selected in pages 22 to 26 ( If no center speaker is connected, select “NONE.” Refer to page 86 for each selection item. through SPEAKER SETUP SIZE:...
  • Page 17 To turn on the player Operation Additional operations Replace the discs in the compartments Press POWER on the player. The player Check if a disc is in the Press LOAD on the with new ones. enters standby mode and the power indicator disc compartment player.
  • Page 18 Selecting a playback layer when Selecting a Playback Area Playing VIDEO CDs with Press X/x to select the setting. playing a hybrid SACD • PLAY LIST: plays the titles created for an SACD Disc PBC Functions (PBC Playback) from “ORIGINAL” for editing. Some SACDs consist of an HD layer and a •...
  • Page 19 To turn off the Control Menu Playing in random order (Shuffle Select the disc you want to program PROGRAM Press DISPLAY repeatedly until the Control – : – – – – using the number buttons or X/x, then Play) Menu is turned off. ALL CLEAR press ENTER.

  • Page 20: Searching For A Scene

    To return to normal play Press X/x to select “SET t,” then Locating a point quickly by playing a disc Press CLEAR, or select “OFF” in Step 3. press ENTER. in fast forward or fast reverse (Scan) Searching for a Scene The “A-B REPEAT”...

  • Page 21: Viewing Information About The Disc

    If there are more than 9 titles, chapters, or tracks, Searching by Scene Press ENTER. V is displayed at the bottom right. (VIEWER) To display the additional titles, chapters, or tracks, select the bottom right scene (the position 9) and press x.

  • Page 22: Sound Adjustments

    Checking the Play Press TIME/TEXT repeatedly to Press ENTER. change the time information. Information (ADVANCED) TIME/TEXT The display and the kinds of time that you BRAHMS SYMPHONY NO – 4 can change depend on the disc you are To close the ADVANCED window playing.
  • Page 23 For 4 to 6 speaker setups • DTS SURROUND Mode Settings (If you select “NONE” in the setting of When an LFE signal component is output, “REAR” in “SPEAKER SETUP” (page “LFE” is enclosed in a solid line. When an 86), you cannot select these modes.) LFE signal component is not output, “LFE”...

  • Page 24: Enjoying Movies

    • If the player is set up to output the signal from the DIGITAL OUT (OPTICAL or COAXIAL) jack, the PLAY 1 2 ( 2 7 ) TVS effect will not be heard when you play a CD. DVD VIDEO Enjoying Movies 1 8 ( 3 4 ) •...

  • Page 25: Using Various Additional Functions

    • DYNAMIC 1: produces a bold dynamic As the value increases, the outlines of Adjusting the Playback picture by increasing the picture Enhancing the Playback images on your TV screen will become contrast and the color intensity. Picture (VIDEO EQUALIZER) crisper.

  • Page 26: The Supplied Remote

    The lower the value, the more strict the Area Code Press X/x to select “PLAYER t,” then Press X/x to select “STANDARD,” then limitation. press ENTER. press ENTER. Standard Code Standard Code The selection items for “STANDARD” x If you have not entered a password number number are displayed.

  • Page 27: Settings And Adjustments

    Philco 03,04 Philips 08,21 (Mega Control) Centurion Pioneer Coronado Portland MEGA CONTROL You can control a Sony CD changer of 5/50/ Curtis-Mathes Quasar 06,18 200/300/400 discs connected to the MEGA Daytron Radio Shack 05,14 TV/DVD CONTROL jack of the player.
  • Page 28 If you select “OTHERS t” in “MENU,” Select an item using X/x, then press Setting the Display or Settings for the Display “SUBTITLE,” and “AUDIO,” select and enter the ENTER. language code from the list using the number buttons Sound Track Language (page 97).
  • Page 29 xCD DIRECT xAUDIO DRC (Dynamic Range Notes Settings for the Sound Control) (DVD VIDEO/DVD-RW only) Eliminates the use of unnecessary circuits • The player can store the settings of up to 50 discs. when playing CDs. The setting will be Makes the sound clear when the volume is (AUDIO SETUP) When you store the setting of disc number 51, the...

  • Page 30: Additional Information

    (– Play mode. Select “SPEAKER SETUP” in the Setup Sony dealer. 6dB [L] to +6dB [R], 0.5dB , The player is in fast forward or fast reverse Display. increments).
  • Page 31 , The DVD prohibits the changing of the , Resume Play has been selected. number) player has performed the self- subtitles. , Contact your Sony dealer or local authorized diagnosis function. During stop, press on the player or the Sony service facility.

  • Page 32: Language Code List

    Semiconductor laser Signal format system NTSC TV Virtual Surround (TVS) (page 58) Technology from Sony developed to produce Audio characteristics surround sound for home use using just a Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz (-2 dB ± 2.0 dB at 44 kHz) stereo TV.
  • Page 33 CUSTOM SETUP (page 81) SPEAKER SETUP (page 86) AUTO PLAY SIZE FRONT LARGE TIMER SMALL DEMO1 CENTER NONE DEMO2 LARGE DIMMER BRIGHT SMALL DARK REAR NONE LARGE (REAR) PAUSE MODE AUTO LARGE (SIDE) FRAME SMALL (REAR) SMALL (SIDE) PLAYBACK MEMORY SUBWOOFER NONE TRACK SELECTION...

  • Page 34: Upper Case Removal

    DVP-NC650V SECTION 2 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2-1. UPPER CASE REMOVAL 2-3. FRONT PANEL SECTION REMOVAL 2 Two screws (3 x 8) 4 Upper case 1 Two tapping screws 1 Connector (CN751) 3 Three tapping...

  • Page 35: Av-60 Board Removal

    2-5. AV-60 BOARD REMOVAL 2-7. TABLE ASS’Y REMOVAL 5 Bracket (guide B1) (black) 4 Bracket 1 Eleven screws (B3) (guide B1) (silver) 8 Table ass’y 2 Two brackets (guide B1) (silver) 3 Two screws (B3) 2 AV-60 board 7 Flexible flat cable 1 Two screws (B3) (FCS-005: CN306) 2-6.

  • Page 36: Bu Holder Ass'y Removal

    2-9. BU HOLDER ASS’Y REMOVAL 2-11. CHASSIS ASS’Y REMOVAL 2 Two screws 1 Two screws 3 Chassis ass’y 1 Eight screws (B3) (B3) (B3) 3 Bracket (CP) 4 Screw 6 BU holder ass’y (M3 × 12) 2 Two connectors 5 Two flexible flat cables (FOM-001, FMM-040) 2-10.

  • Page 37: Power Block Removal

    2-13. POWER BLOCK REMOVAL 7 PWB cover 1 Power striker 5 Claw 8 Power block 4 Connector 6 Claw (CN101) 2 Two screws (3 x 8)

  • Page 38: Internal Views

    2-14. INTERNAL VIEWS PH501 Disc presence detection sensor 8-749-924-30 Optical pick-up (KHM-240 AAA/J1RP) 8-820-144-06 M951 PH502 DC motor (turn table) Roulette position 1-541-632-12 detection sensor 8-749-924-18 Rotary encoder (loading) 1-466-996-21 M851 Loading motor ass’y A-4660-977-A...

  • Page 39: Circuit Boards Location

    2-15. CIRCUIT BOARDS LOCATION TM-125 (TURNTABLE MOTOR) POWER BLOCK SE-123 (MPN4801) (SENSOR) LM-64 (LOADING MOTOR) AV-60 (AUDIO/VIDEO OUT) FR-180 (FUNCTION SWITCH) MB-101 HP-133 (SIGNAL PROCESS, (HEAD PHONE) SERVO) CN-143 (CONNECTION) SW-356 IF-85 (FUNCTION SWITCH) (INTERFACE CONTROL) FL-124 (FUNCTION SWITCH) 2-6 E...

Table of Contents