Related Manuals for IBM System Storage N3220
Summary of Contents for IBM System Storage N3220
- Page 1 IBM System Storage N3220 Installation and Setup Instructions Covering the N3220 model GA32-2202-02...
- Page 2 Attention Department GZW 9000 South Rita Road Tucson, AZ 85744-0001 www.ibm.com/storage/support/nseries References in this publication to IBM products or services do not imply that IBM intends to make them available in every country or region. ® IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business Machines Corporation in the United States, other countries, or both.
-
Page 3: Table Of Contents
Installation and setup instructions ......1 Unpacking the N3220 filer . Installing the rails in an IBM 19-inch rack Installing the N3220 filer in the rack Setting storage expansion unit shelf IDs . -
Page 5: Before You Begin
About the IBM N series support website The IBM System Storage N series support website requires users to register in order to obtain access to N series support content on the web. To understand how the N series support web content is organized and navigated, and to access the N series support website, go to the following publicly accessible web page: ©... - Page 6 If the N series product is being installed in a non-IBM rack, the rails shipped with the N series product may or may not work with the non-IBM rack. Physical installation of the N series product in a non-IBM...
-
Page 7: Overview Of The N3220
Shelf activity LED Disk drive fault LED Two-digit shelf ID digital display Right mounting flange Button for changing the shelf ID Note: Disk drive bays are numbered horizontally starting from 0 to 23 (left to right). © Copyright IBM Corp. 2013... - Page 8 Figure 2. Rear view SAS ports (2) ACP port (locked wrench icon) PCM fault LED Gigabit Ethernet ports (4) NVMEM LED PSU OK LED Mezzanine card ports 10 Gb option DC fault LED Mezzanine card ports 8 Gb Fibre Channel option AC fault LED Controller modules (1 or 2 depending on the Fan fault LED...
-
Page 9: Installation And Setup Instructions
Each shipment container includes the following contents: v N3220 system enclosure v N3220 system bezel v IBM System Storage N3220 Installation and Setup Instructions v General information kit, containing warranty, safety, and environmental information v Software license CAUTION: The weight of this part or unit is 25.4 kg (56.0 lb). -
Page 10: Installing The Rails In An Ibm 19-Inch Rack
Installing the rails in an IBM 19-inch rack Use these instructions to install the rails on which you will mount the N3220 filer. Note: Read this document in its entirety before proceeding. 1. Loosen (but do not remove) the four rail adjustment screws on each rail, as shown in Figure 3. -
Page 11: Installing The N3220 Filer In The Rack
FRONT REAR Section of rack EIA rail Left and Right Left and Right Rails Rails Chassis attach screws Top rail screw 1 EIA unit (1U) Locating pins Locating pins Bottom rail screw Chassis attach screws Bottom rail screw Figure 4. N3220 rail mounting template Using one silver pan head M5 screw, attach the rail to the front of the rack using hole H6. - Page 12 Figure 5. Mounting the N3220 filer in the rack 3. Using Figure 5 for reference, attach the N3220 filer to the front of the rack using four silver pan head screws (two for each rail) in the H2 and H5 holes. Thread the screws through the front flange, the spacer plate, and the rack frame rail into the threaded rail nuts.
-
Page 13: Setting Storage Expansion Unit Shelf Ids
Setting storage expansion unit shelf IDs Use these instructions to set the storage expansion unit shelf IDs. Setting SAS expansion unit shelf IDs A unique shelf ID (from 00 to 98) is required for each SAS storage expansion unit in a SAS stack. ID 00 is used by default for the controller's internal disks. -
Page 14: Setting Exn4000 Or Exn1000 Storage Expansion Unit Shelf Ids
Setting EXN4000 or EXN1000 storage expansion unit shelf IDs A unique shelf ID (from 1 to 7) is required for each EXN4000 or EXN1000 storage expansion unit in a loop. Shelf ID 1 is used for the first EXN4000 or EXN1000 storage expansion unit in a new loop. Shelf IDs for additional storage expansion units are incremented sequentially from the number of the first unit. -
Page 15: Connecting The N3220 Filer To A Network
Connecting the N3220 filer to a network Use these instructions to connect the N3220 filer to a network. Perform the steps in this section for each N3220 controller node. Note: Use the cable management arms and hook-and-loop fasteners to organize your cabling. Port labels Console Fibre... - Page 16 LNK / LNK / Figure 12. Cabling the networking and management ports for 10 GbE connections in 7-Mode v For 10/100/1000 setup in switchless Clustered Data ONTAP: Connect the system to the data network switch ( 1 in Figure 13 and Figure 14 on page 9) by plugging the network cables into the networking ports, labeled e0a, e0b, e0c, and e0d.
-
Page 17: Connecting The System To Expansion Units
For detailed information about cabling N series SAS storage expansion units, such as the EXN3000 or EXN3500, refer to the IBM System Storage N series Universal SAS and ACP Cabling Guide. The SAS ports and ACP ports on the SAS storage expansion unit IOMs are designated by square and circle symbols. All cabling is done in reference to connecting to either square or circle ports. -
Page 18: Installing The Power Cables
1. Make sure the Configuration worksheet from the Data ONTAP Software Setup Guide for 7-Mode is completed and available for use. Note: IBM recommends that you print a copy of this worksheet from the Data ONTAP Software Setup Guide for 7-Mode. -
Page 19: Setting Up And Booting The System In Clustered Data Ontap
Refer to the Data ONTAP High Availability and MetroCluster Configuration Guide for 7-Mode to verify that the system is set up correctly and ready to operate. 11. IBM recommends that you enable AutoSupport and then use the AutoSupport feature to view the health of the system. -
Page 21: Appendix. Troubleshooting And Additional Resources
Check the Platform Monitoring Guide for your N series storage expansion units for information about LED responses. 8. Use the system-level diagnostics to check the disks. For more information, see the IBM System Storage N series System-Level Diagnostics Guide. 9. If your system does not boot successfully, it might not have the boot image downloaded on the boot device. - Page 22 ONTAP Replacing components IBM System Storage N3150, N3220, and N3240 Hardware and Service Guide Safety information IBM System Storage N series Safety Notices The IBM N series support site contains additional information about N series hardware and software products: www.ibm.com/storage/support/nseries...
- Page 24 Part Number: 00GM241 Printed in USA GA32-2202-02...