Related Manuals for Sony SLV-SE700G
Summary of Contents for Sony SLV-SE700G
- Page 1 3-868-272-11 (1) Video Cassette Recorder Operating Instructions PAL NTSC4.43 SLV-SE700G SLV-SE700I SLV-SE800G SLV-SE800I © 2000 Sony Corporation...
- Page 2 If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station. Precautions Safety •...
-
Page 3: Table Of Contents
Table of contents Getting Started 4 Step 1 : Unpacking 5 Step 2 : Setting up the remote commander 9 Step 3 : Connecting the VCR 13 Step 4 : Setting up the VCR with the Auto Set Up function 14 Step 5 : Tuning your TV to the VCR 17 Selecting a language 19 Presetting channels... -
Page 4: Getting Started
Getting Started Step 1 : Unpacking Check that you have received the following items with the VCR: • Remote commander • R6 (size AA) batteries Check your model name The instructions in this manual are for the 4 models: SE700G, SE700I, SE800G and SE800I. -
Page 5: Step 2 : Setting Up The Remote Commander
Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have symbol near the remote sensor, this remote commander will not operate the TV. - Page 6 FASTEXT buttons TV control buttons Set the TV to standby mode Select an input source: aerial in or line in Select the TV’s programme position Setting up the remote commander WIDE AUDIO MONITOR DISPLAY t TV/VIDEO Programme number buttons PROG +/–/ 2 +/–...
-
Page 7: Controlling Other Tvs With The Remote Commander
• Some buttons may not work with certain Sony TVs. Controlling other TVs with the remote commander The remote commander is preprogrammed to control non-Sony TVs. If your TV is listed in the following table, set the appropriate manufacturer’s code number. - Page 8 If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. To switch to wide mode, see the footnotes below this table for the applicable code numbers. Manufacturer Sony Akai Ferguson Grundig Hitachi...
-
Page 9: Step 3 : Connecting The Vcr
Step 3 : Connecting the VCR If your TV has a Scart (EURO-AV) connector, see page 10. If your TV does not have a Scart (EURO-AV) connector Mains lead to mains : Signal flow Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. - Page 10 If your TV has a Scart (EURO-AV) connector Mains lead to mains : Signal flow Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR. Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.
- Page 11 About the SMARTLINK features If the connected TV complies with SMARTLINK, MEGALOGIC* EASYLINK* , Q-Link* LINK* , or T-V LINK* automatically runs the SMARTLINK function after you complete the steps on the previous page (the SMARTLINK indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
-
Page 12: Additional Connections
Note • You cannot watch programmes on the TV while recording unless you are recording a programme from your set top box. SLV-SE800G and SE800I only SLV-SE700G and SE700I only Connecting the VCR AUDIO OUT LINE IN Audio cable (not supplied) -
Page 13: Step 4 : Setting Up The Vcr With The Auto Set Up Function
Step 4 : Setting up the VCR with the Auto Set Up function Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the TV channels, guide channels for the VIDEO Plus+ system, and VCR clock automatically. -
Page 14: Step 5 : Tuning Your Tv To The Vcr
Refer to your TV manual for TV tuning instructions. If the picture does not appear clearly, see “To obtain a clear picture from the VCR.” below. Tuning your TV to the VCR RF CHANNEL PROGRAM +/– SONY VIDEO CASSETTE RECORDER... - Page 15 Press RF CHANNEL. AUTO SET UP You have now tuned your TV to the VCR. Whenever you want to play a tape, set the TV to the video channel. RF CHANNEL To check to see if the TV tuning is correct Set the TV to the video channel and press PROGRAM +/–...
- Page 16 If your TV has a Scart (EURO-AV) connector Press RF CHANNEL on the VCR lightly. AUTO SET UP The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV. RF CHANNEL Press PROGRAM +/–...
-
Page 17: Selecting A Language
Selecting a language If you prefer an on-screen language other than English, use the on-screen display to select another language. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. Press MENU, then press M/m to highlight MENU SETTINGS and press OK. - Page 18 Press M/m/</, to highlight the desired language, then press OK. PLAY Press MENU to exit the menu. MENU • If you want to return to the previous menu, highlight RETURN and press OK. Note • The menu disappears automatically if you don’t proceed for more than a few minutes. Selecting a language...
-
Page 19: Presetting Channels
Presetting channels If some channels could not be preset using the Auto Set Up function, you can preset them manually. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. Press MENU, then press M/m to highlight MENU SETTINGS and press OK. - Page 20 Press M/m to highlight TUNER, then press PLAY SLV-SE700I and SE800I only: Press M/m to highlight NORMAL/CATV, PLAY then press OK. SLV-SE700I and SE800I only: Press M/m to highlight NORMAL, then PLAY press OK. To preset CATV (Cable Television) channels, select CATV. Press PROG +/–...
- Page 21 Press M/m repeatedly until the channel you want is displayed. The channels appear in the following PLAY order: • VHF IA - IJ, SA10 - SA13 (SLV-SE700I and SE800I only) • UHF B21 - B69 • CATV S1 - S20 (SLV-SE700I and SE800I only) •...
-
Page 22: If The Picture Is Not Clear
If the picture is not clear Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. However, if the picture is not clear, you may also use the manual tuning function. Press PROG +/– or the programme number buttons to select the programme position for which you cannot obtain a clear picture. -
Page 23: Changing/Disabling Programme Positions
Changing/disabling programme positions After setting the channels, you can change the programme positions as you like. If any programme positions are unused or contain unwanted channels, you can disable them. You can also change the station names. If the station names are not displayed, you can enter them manually. - Page 24 Press M/m to highlight the row which you want to change the programme position, PLAY then press ,. To display other pages for programme positions 6 to 60, press M/m repeatedly. Press M/m until the selected channel row moves to the desired programme position. PLAY The selected channel is inserted at the new programme position and the intermediate...
- Page 25 Disabling unwanted programme positions After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. Press MENU, then press M/m to highlight MENU LISTS, and press OK.
- Page 26 Press M/m to highlight the row which you want to disable. PLAY Press CLEAR. CLEAR The selected row will be cleared as shown on the right. Repeat steps 3 and 4 for any other programme positions you want to disable. Press MENU to exit the menu.
-
Page 27: Before You Start
Changing the station names You can change or enter the station names (up to 5 characters). The VCR must receive channel information (for instance, SMARTLINK information) for station names to appear automatically. Before you start… • Turn on the VCR and the TV. •... - Page 28 Press ,. PLAY Enter the station name. 1 Press M/m to select a character. PLAY Each time you press M, the character changes as shown below. A t B t … t Z t a t b t … t z t 0 t 1 t …...
-
Page 29: Setting The Clock
Setting the clock You must set the time and date on the VCR to use the timer features properly. If the VCR clock was not set in the Auto Set Up procedure, you need to set it manually. The Auto Clock Set function works only if a station in your area is broadcasting a time signal. - Page 30 Press M/m to highlight MANUAL ADJUST, then press OK. PLAY Press M/m to set the day. PLAY Press , to highlight the month and set the month pressing M/m. PLAY Set the year, hour, and minutes in sequence, pressing , to highlight the PLAY item to be set, and press M/m to select the digits.
- Page 31 Press MENU to exit the menu. MENU Tips • To change the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m. • If you want to return to the previous menu, highlight RETURN and press OK. Note •...
- Page 32 Changing the station for the Auto Clock Set function Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. Press MENU, then press M/m to highlight MENU SETTINGS and press OK. PLAY Press M/m to highlight CLOCK, then press PLAY...
- Page 33 Press M/m to highlight ON, then press OK. PLAY Press m to highlight CLOCK PROGRAM, then press OK. PLAY Press M/m repeatedly until the programme position of the station that carries a time PLAY signal appears. If the VCR does not receive a time signal from any station, AUTO ADJUST returns to OFF automatically.
-
Page 34: Setting Your Personal Code
Setting your personal code For identification, you can enter a personal code into the VCR. Once you enter your personal code, you can confirm it any time but can never change it. Please make a note of the code to quote to the police if your VCR is stolen. - Page 35 Enter your personal code. 1 Press M/m to select a character. PLAY Each time you press M, the character changes as shown below. A t B t … t Z t 0 t 1 t … t 9 t (blank space) t – (hyphen) t A 2 Press , to set the next character.
-
Page 36: Basic Operations
Basic Operations Playing a tape NTSC PB Turn on your TV and set it to the video channel. Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. Playing a tape Z EJECT DISPLAY CLEAR... - Page 37 Press H PLAY. When the tape reaches the end, it will rewind automatically. PLAY Additional tasks Stop play Pause play Resume play after pause Fast-forward the tape Rewind the tape Eject the tape To play an NTSC-recorded tape Set NTSC PB at the rear of the VCR according to the colour system of your TV. When your TV is PAL only PAL and NTSC...
- Page 38 Notes • The counter resets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no recording. • The time counter does not appear on the TV screen when using an NTSC-recorded tape. •...
-
Page 39: Recording Tv Programmes
Recording TV programmes Turn on your TV and set it to the video channel. Insert a tape with its safety tab in place. COUNTER/ REMAIN DISPLAY SP/LP t TV/VIDEO PROG +/– z REC x STOP continued Recording TV programmes... - Page 40 Press PROG +/– to select the programme position or station name you want • PROG to record. Press SP/LP to select the tape speed, SP or LP. SP / LP LP (Long Play) provides recording time twice as long as SP. However, SP (Standard Play) produces better picture and audio quality.
- Page 41 To save a recording To prevent accidental erasure, break off the safety tab as illustrated. To record on the same tape again, cover the tab hole with adhesive tape. Tips • To select a programme position, you can use the programme number buttons on the remote commander.
- Page 42 Recording what you are watching on the TV (TV Direct Rec) If you use the SMARTLINK connection, you can easily record what you are watching on the TV (other than tapes being played on the VCR). Insert a tape with its safety tab in place. Press z REC while you are watching a TV programme or external source.
-
Page 43: Recording Tv Programmes Using The
Recording TV programmes using the Dial Timer (SLV-SE800G and SE800I only) The Dial Timer function allows you to make timer recordings of programmes without turning on your TV. Set the recording timer to record up to eight programmes, including settings made with other timer methods, that will be broadcast within the next month. -
Page 44: Dial Timer
Turn DIAL TIMER to set the recording date. DIAL TIMER Press DIAL TIMER. DIAL TIMER “START” and the current time appear alternately in the display window. Turn DIAL TIMER to set the recording start time. DIAL TIMER You can set the recording start time in 15 minute intervals or adjust the time in one minute intervals by pressing the PROGRAM +/–... -
Page 45: Dial Timer
Turn DIAL TIMER to set the recording stop time. DIAL TIMER You can set the recording stop time in 15 minute intervals or adjust the time in one minute intervals by pressing the PROGRAM +/– buttons. PROGRAM TRACKING Press DIAL TIMER. DIAL TIMER The programme position or station name appears in the display window. -
Page 46: Dial Timer
To use the VCR after setting the timer To use the VCR before a recording begins, just press ?/1. The and the VCR switches on. Remember to press ?/1 to reset the VCR to recording standby after using the VCR. You can also do the following tasks while the VCR is recording: •... -
Page 47: Dial Timer
About the Demonstration Mode The Dial Timer function has a Demonstration Mode that allows the user, such as a salesperson, to enter more than eight examples of timer settings when demonstrating the use of the Dial Timer. It cancels the FULL notice which appears if eight programmes have already been set. -
Page 48: Recording Tv Programmes Using The Video Plus+ System
Recording TV programmes using the VIDEO Plus+ system The VIDEO Plus+ system is the feature that simplifies programming the VCR to make timer recordings. Just enter the PlusCode listed in the TV programme guide. The date, times, and programme position of that programme are set automatically. - Page 49 Press TIMER. TIMER • When you set TIMER OPTIONS to VARIABLE: The TIMER METHOD menu appears on the TV screen. Press M/m to select PLAY VIDEO Plus+, then press OK. • When you set TIMER OPTIONS to VIDEO Plus+: The VIDEO Plus+ menu appears on the TV screen.
- Page 50 If you want to change the date, tape speed, and the VPS/PDC setting: PLAY 1 Press </, to highlight the item you want to change. 2 Press M/m to reset it. • To record the same programme every day or the same day every week, see “Daily/weekly recording”...
- Page 51 To record a programme from your set top box If you connect a set top box and the VCR, you can record a programme from your set top box. Turn on the set top box. On the set top box, select the programme for which you want to make a timer setting.
-
Page 52: Setting The Timer Manually
Setting the timer manually If the VIDEO Plus+ system is not available in your area, follow the instructions below to set the timer to record programmes. … Before you start • Check that the VCR clock is set to the correct time and date. - Page 53 Press TIMER. TIMER • When you set TIMER OPTIONS to VARIABLE: The TIMER METHOD menu appears on the TV screen. Press M/m to select PLAY STANDARD, then press OK. • When you set TIMER OPTIONS to STANDARD: The TIMER menu appears on the TV screen.
- Page 54 To stop recording To stop the VCR while recording, press x STOP. Daily/weekly recording In step 2 above, press m to select the recording pattern. Each time you press m, the indication changes as shown below. Press M to change the indication in reverse order.
-
Page 55: Additional Operations
Additional Operations Playing/searching at various speeds SLV-SE800G, SE800I Shuttle ring SLV-SE700G, SE700I Playback options View the picture during fast- forward or rewind H PLAY H PLAY Operation During fast-forward, hold down M down m REW/m. Playing/searching at various speeds ×2 y SLOW FF/M. -
Page 56: Using The Shuttle Ring
Playback options Play at high speed Play at twice the normal speed Play in slow motion Play frame by frame Rewind and start play To resume normal playback Press H PLAY. Using the shuttle ring (SLV-SE800G and SE800I only) With the shuttle ring, you can operate a variety of playback options. There are two ways for using the shuttle ring, normal mode and jog mode. - Page 57 To use the shuttle ring in jog mode Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The JOG button lights up. If you change to the jog mode during any playback mode, playback pauses so you can see a still picture. Each change in the shuttle ring position shifts the picture one frame.
-
Page 58: Setting The Recording Duration Time
Setting the recording duration time After you have started recording in the normal way, you can have the VCR stop recording automatically after a specified duration. While recording, press z REC. indicator appears in the display window. Press z REC repeatedly to set the duration time. Each press advances the time in increments of 30 minutes. -
Page 59: Synchronized Recording (Slv-Se800G And Se800I Only)
Synchronized Recording (SLV-SE800G and SE800I only) You can set the VCR to automatically record programmes from equipment such as a set top box by connecting the equipment to the LINE-3 IN connector. The connected equipment must have a timer function for this feature to work. When the connected equipment turns on, the VCR also automatically turns on and starts recording a programme from LINE-3 IN. -
Page 60: Slv-Se800G And Se800I Only
Recording programmes using the Synchronized Recording function Before you start... • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time. SYNCHRO REC Press INPUT SELECT or PROG +/– to display “L3” in the display window. Set the timer on the connected equipment to the time of the programme you want to record, then turn it off. -
Page 61: Slv-Se800G And Se800I Only
Notes • This function may not work with some types of set top boxes. • Some TVs or other equipment with timer functions will automatically turn off if no operation is performed within a certain amount of time. In this case, the Synchronized Recording also stops automatically. -
Page 62: Checking/Changing/Cancelling Timer Settings
Checking/changing/cancelling timer settings … Before you start • Turn on your TV and set it to the video channel. Press ?/1 to turn on the VCR. Press MENU, then press M/m to highlight LISTS and press OK. Press M/m to highlight TIMER LIST, then press •... - Page 63 Press M/m to select the setting you want to change or cancel, then press OK. The selected setting appears in the TIMER menu. • To change the setting, press </, to highlight the item you want to change, then press M/m to reset it. •...
-
Page 64: Recording Stereo And Bilingual Programmes
Recording stereo and bilingual programmes In NICAM system This VCR receives and records stereo and bilingual programmes based on the NICAM system (The NICAM indicator appears). When a stereo or bilingual programme is received, the STEREO indicator appears in the display window. To record a NICAM programme, HIFI AUDIO in the OPTIONS-1 menu should be set to NICAM (initial setting). - Page 65 How sound is recorded on a video tape The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape. Stereo Normal audio track (monaural)
-
Page 66: Searching Using The Smart Search Function
Searching using the Smart Search function If you record multiple programmes on a tape, use the Smart Search function to see what has been recorded on your tape. You can see information such as date, time, and programme position of programmes recorded on a tape. - Page 67 Press OK. The VCR starts searching, and playback starts automatically from the beginning of the selected programme. To stop searching Press x STOP. To exit the SMART SEARCH screen Press SMART SEARCH. To record in a blank space Blank space on the tape will appear as a blank row in the SMART SEARCH screen.
- Page 68 Press M/m to highlight LATEST DATA. If you want to reset the latest data screen, highlight NO DATA and press OK, then record a programme. Press OK. The latest data stored in the VCR’s memory is displayed. Tips • You can store information for up to 24 programmes on a single list. •...
-
Page 69: Searching Using The Index Function
Searching using the index function The VCR automatically marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording. Insert an indexed tape into the VCR. Press ./> INDEX SEARCH. •... -
Page 70: Adjusting The Picture
Adjusting the picture Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the flashes in the display window, then turns off), distortion may occur if the recording is in poor condition. In this case, manually adjust the tracking. During playback, press TRACKING +/–... - Page 71 To deactivate the OPC function Set OPC to OFF in the OPTIONS-1 menu. The OPC indicator in the display window turns off. • To set tracking to the centre position, press the TRACKING + and – buttons at the same time. Notes •...
-
Page 72: Changing Menu Options
Changing menu options Press MENU, then select OPTIONS and press Press M/m to highlight OPTIONS-1 or OPTIONS-2, then press OK. Press M/m to select the option, then press OK. Press M/m to change the setting, then press OK. Press MENU to return to the original screen. Menu choices Initial settings are indicated in bold print. - Page 73 Menu option Set this option to AUTO LONG PLAY • ON to change the timer recording tape speed automatically to the LP mode when the remaining tape length becomes shorter than the recording time. Note that for AUTO LONG PLAY to work correctly, the TAPE LENGTH setting must be accurate.
-
Page 74: Editing
Editing Connecting to a VCR or stereo system How to connect to record on this VCR Connect the line outputs of the other VCR to the LINE IN connector or jacks of this VCR. Refer to the examples A through C and choose the connection that best suits your VCR. -
Page 75: System
• If the other VCR does not have a Scart (EURO-AV) connector, use the VMC-2106HG cable instead and connect the cable to the line out jacks of the other VCR. SLV-SE800G and SE800I only SLV-SE700G and SE700I only t LINE-3 IN* Other VCR (Player) -
Page 76: Basic Editing
Basic editing (when recording on this VCR) Before you start editing • Turn on your TV and set it to the video channel. • Press INPUT SELECT to display the connected line in the display window. • Press SP/LP to select the tape speed, SP or LP. •... -
Page 77: Audio Dubbing (Slv-Se800G And Se800I Only)
Audio dubbing (SLV-SE800G and SE800I only) This feature lets you record over the normal audio track. The monaural sound previously recorded is replaced while the original hi-fi sound remains unchanged. Use this feature to add commentary to a tape that you have recorded with a camcorder. -
Page 78: Slv-Se800G And Se800I Only
To start editing, press the X (pause) buttons on this VCR and the stereo system (or other VCR) at the same time. After you use this feature, the audio in playback mode is automatically set to monaural. To stop editing Press x STOP on this VCR and the stereo system (or other VCR). -
Page 79: Additional Information
Additional Information Troubleshooting If you have any questions or problems not covered below, please consult your nearest Sony service facility. Symptom The ?/1 ON/STANDBY switch does not function. The power is turned on but the VCR does not operate. The VCR is plugged in but the display window remains dark. - Page 80 Troubleshooting Remedy • Adjust the tracking. • The video heads are dirty. Clean the video heads using the Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning cassette as explained above. • Make sure the TV is set to the video channel. If you are using a monitor, set it to video input.
- Page 81 Symptom Remedy The SYNCHRO REC • The tape has reached its end. Insert a new tape and press button turns off while SYNCHRO REC again. recording or does not go back to recording standby mode. The Synchronized • The connected equipment was not turned off. Recording function does not Turn off the connected equipment and press SYNCHRO REC work.
- Page 82 Symptoms caused by contaminated video heads • Normal picture Troubleshooting • Rough picture • Unclear picture initial contamination • No picture (or black & white screen appears) terminal...
-
Page 83: Specifications
Approx. 430 × 100 × 290 mm (Approx. 17 × 4 × 11 inches) (w/h/d) (SLV-SE800G, SE800I) Mass Approx. 4.3 kg (Approx. 9 lb 08 oz) (SLV-SE700G, SE700I) Approx. 4.4 kg (Approx. 9 lb 11 oz) (SLV-SE800G, SE800I) Supplied accessories... -
Page 84: Index To Parts And Controls
Index to parts and controls Refer to the pages indicated in parentheses ( ) for details. Front panel SLV-SE800G, SE800I A ?/1 ON/STANDBY switch (34) B Tape compartment C Remote sensor (5) D A EJECT button (37) E Shuttle ring (56) F H PLAY button (37) (56) G JOG button (57) H z REC (record) button (40) (58) (76) - Page 85 SLV-SE700G, SE700I A ?/1 ON/STANDBY switch (34) B Tape compartment C Remote sensor (5) D A EJECT button (37) E H PLAY button (37) (56) F z REC (record) button (40) (58) (76) G X (pause) button (37) (76) H x STOP button (34) (37) (76)
-
Page 86: Display Window
Display window STEREO NICAM LP A Timer indicator (45) (50) (53) B NICAM indicator (64) C STEREO indicator (64) D Tape speed indicators (40) E VIDEO indicator (10) (40) F VPS (Video Programme System)/PDC (Programme Delivery Control) indicator (50) G OPC (Optimum Picture Control) indicator (70) * SLV-SE800G and SE800I only Index to parts and controls... -
Page 87: Rear Panel
B t LINE-2 IN connector* t LINE-3 IN connector* (75) C AERIAL IN ANTENNE ENTREE connector (9) (10) SLV-SE700G and SE700I only SLV-SE800G and SE800I only D AERIAL OUT ANTENNE SORTIE connector (9) (10) (12) (75) E i LINE-1 (TV) -
Page 88: Remote Commander
Remote commander Index to parts and controls A Z EJECT button (37) B WIDE button (for TV) (7) C AUDIO MONITOR button (64) D ×2 button* (56) E y SLOW button* (56) F SP (Standard Play)/LP (Long Play) button (40) DISPLAY button (40) H - (ten’s digit) button (6) (41) I 2 (volume) +/–... - Page 89 M [TV] / [VIDEO] remote control switch (5) N ?/1 (on/standby) switch (6) (50) O COUNTER/REMAIN button (40) / (Teletext) button (for TV) (7) P a TV power on/TV mode select button (for TV) (6) Q ./> INDEX SEARCH buttons* (69) R CLEAR button (37) (49) (63) S t TV/VIDEO button (6) (10) (40)
- Page 90 Index to parts and controls...
- Page 91 Index to parts and controls...
-
Page 92: Index
Disabling the programme positions 25 Dubbing. see Editing Editing 74 EP mode 38 Hi-fi audio track 65 Index search 69 Sony Corporation Printed in France Language selecting 17 LP mode 40 Monaural 64 Monitoring during playback 64 during recording 64...