Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eachine TYRO109
Summary of Contents for Eachine TYRO109
- Page 1 TYRO109 QUICK START GUIDE (DIY)
- Page 2 TYRO109 QUICK START GUIDE Package Included: 1 x 210mm frame kit 2 x 2206 2400KV brushless motor CW 2 x 2206 2400KV brushless motor CCW 1 x 4 IN 1 30A BLHeli_S ESC 1 x Customized F4 flight controller 1 x Caddx Turbo Eos2 1200tvl 1 x XF5804 5.8G 40CH 0mw/25mw/200mw/...
-
Page 3: Table Of Contents
TYRO109 QUICK START GUIDE Contents 1.0 Frame kit----------------------------------------04 Motor----- ----------------------------------------04 3.0 Esc------------------------------------------------05 4.0 Flight controller---------------------------------06 5.0 Camera-------------------------------------------07 6.0 Switchable VTX--------------------------------07-08 7.0 Pagoda Antenna-------------------------------08 8.0 Propeller-----------------------------------------08 9.0 Screws--------------------------------------------09 10.0 Exploded view---------------------------------10 11.0 Adjusting parameter----------------------------11-12... -
Page 4: Frame Kit
TYRO109 QUICK START GUIDE 1.0 Frame kit Wheel base: 210mm Frame arm thickness: 5mm Bottom plate thickness: 2mm Side plate thickness: 2mm Frame kit material: 3K carbon fiber & 6065 aluminium 1.5mm Top Plate 6065 aluminium 1.5mm Side plate 3mm Bottom Plate... -
Page 5: Esc
TYRO109 QUICK START GUIDE 3.0 ESC Continuous current: 30A Peak Current: 40A(10S) Input voltage: 2-5S BEC: 5V 2A BEC Main control chip: 48Mhz EFM8BB2 Firmware: BLHeli_S supports Dshot600 MOS: 5*6 Product characteristics: The high performance EFM8BB21F16G microprocessor is used to run up to 48MHz.The high quality 5 * 6 package MOSFET is more reliable than the 3 * 3 package MOSFET.6 layers of high... -
Page 6: Flight Controller
TYRO109 QUICK START GUIDE 4.0 Flight controller Product characteristics: The STM32 F405 master chip can run higher PID cycle time and gyroscope.Integrating accelerometers and gyroscopes using an ICM20602 chip with SPI bus (the highest operating frequency of the gyroscope can be set to32KHz);Flight control board OSD chip, supporting DMA mode (using F4 MCU to control OSD), can use Beta Flight tuning softwarePart adjustment parameters;... -
Page 7: Camera
TYRO109 QUICK START GUIDE 5.0 Camera Model：Turbo EOS1 Image Sensor：1/3" CMOS Sensor Horizontal Resolution：1200 TVL TV System：NTSC / PAL option IMAGE：4:3 Synchronization：Internal Electronic Shutter：PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio：>52dB (AGC OFF) Video Output：CVBS Lens：2.1mm Min. Illumination：0.001Lux@F1.2 Auto Gain Control：YES BLC：YES Customized ABS Holder WDR：Global WDR... -
Page 8: Pagoda Antenna
TYRO109 QUICK START GUIDE 6.0 Switchable VTX Points for attention: The antenna is installed at the output terminal before power up, so as not to damage internal components.Note that the input voltage is within the specified range and is positive or negative, so as not to damage internal components.If the antenna is replaced,... -
Page 9: Screws
TYRO109 QUICK START GUIDE 9.0 Screws 6xM3*4 10xM3*6 16xM3*8 4xM3*12 4xM3*16 4xM3*30 2xM2*4 M3*5mm ABS Round Isolation Column M3*3.5mm Rubber Shock Absorber M3*3.5mm Rubber Shock Absorber... -
Page 10: Exploded View
TYRO109 QUICK START GUIDE 10.Exploded view -10-... -
Page 11: Adjusting Parameter
TYRO109 QUICK START GUIDE 11.Adjusting parameter 1.Click connect connection 2: Click the RX interface under UART2 under the ports option, as shown in the figure. 3: Click CONFIGURATIN to change to dshot600. 4: Click CONFIGURATIN; change to SBUs 5: Click modes, add arm and angle, drag the slider between 1300... -
Page 12: Adjusting Parameter
TYRO109 QUICK START GUIDE 11.Adjusting parameter 6: Push the slider to test the positive and negative rotation of the motor, such as error, 7: Click font manager, select betaflight, click upload font 8: Click setup, calibrate accelerometer -12-...