Switching On The Tv; Automatically Tuning The Tv - Sony Trinitron KD-32DX40U Quick Start Manual
Hide thumbs
Also See for Trinitron KD-32DX40U:
- Operating instructions manual (40 pages) ,
- Service manual (62 pages)
Advertisement
4
Switching on the TV
1 Connect the TV plug to your mains socket (220 - 240V AC, 50 Hz) and switch on.
2 Push in the On/Off button ( ) on the front of the TV.
If the standby mode indicator on the front of the TV is lit, press the TV
on the remote control to switch on the TV set. Please be patient as the picture may
take a few moments to appear on the TV screen.
5
Automatically tuning the TV
When you first switch on your new TV you need to tune in all the available channels. The 'Auto Tune' feature automatically searches and stores all
the available channels for you. The following instructions and illustrations will guide you through this procedure.
DIGITAL/
button
Numbered buttons
Control Pad
(v,V, OK buttons)
PROG +/- buttons
Your television stations are now stored in your television's memory.
6
On/Off button
Watching a pre-recorded video tape
VIDEO
/
/
TV
/
button
DIGITAL
1. When you switch on the TV for the first time a menu appears on the screen asking
you to check if the picture is slanted. (Sometimes the Earth's natural magnetism can
VIDEO
/
/
TV
cause the screen to look tilted.)
DIGITAL
a) If no correction is required: Press the V or v buttons on the remote control to
1
2
3
highlight 'Not necessary' and press the OK button. Go to Step 2.
4
5
6
b) If some correction is required: Press the V or v buttons on the remote control to
7
8
9
highlight 'Adjust now', then press the OK button. Correct the slant by pressing the
V or v buttons then press the OK button to store.
0
2. The autotune prompt screen appears. Press the OK button to select 'Yes'. The
autotune procedure begins.
The Digital autotune display appears on screen and the search and store procedure
begins. All the available Digital channels will now be captured and stored. As this may
O K
take some time, a message is included in the display to inform you of the tuning
progress.
When Digital tuning is complete, the analogue display appears automatically and the
search and store procedure for the analogue channels begins.
If no Digital and no analogue channels are found, a menu appears asking you to
confirm your aerial is connected. After checking the aerial has been connected, press
OK to begin the autotune procedure again.
Once all Digital and analogue channels have been captured and stored, the TV
returns to normal operation and displays the Digital channel captured on channel
number 1.
3. To view programmes, press the PROG+/- buttons or the numbered buttons on the
remote control. A banner momentarily appears at the top of the screen if you are
watching a Digital channel. To switch between Digital and analogue modes, press the
DIGITAL/
button.
1. You should have inserted a pre-recorded video tape during the 'Connecting an aerial and a VCR' section. To view the video picture press
'PLAY' on the VCR. The TV automatically displays the video picture (providing that you have used a fully wired 21 pin scart lead to connect
your VCR to the TV).
If the video picture does not automatically appear, press the
displayed on the TV screen.
2. Press the DIGITAL/
button on the remote control to return to normal TV mode.
Note:
Alternatively, with the TV in analogue mode, press the PROG +/- buttons on the remote control until the picture from the pre-recorded video tape appears on the TV screen.
If you wish to move your video channel to a different channel number, refer to the 'Programme Sorting' feature in 'The Set Up menu' section of this instruction manual.
Checking the picture tilt
The autotune prompt screen
Tuning the Digital channels
Tuning the analogue channels
/
button on the remote control repeatedly until the video picture is
If picture slants, please
adjust picture rotation.
Not necessary
Adjust now
OK
OK
Auto T uning
Programme:
02
Channel :
C29
Completed
16%
Advertisement
