Advertisement
Quick Links
GSMX4G / GSMXCN4G GSM Communicator – Quick Installation Guide
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
General Information
The GSMX4G GSM Communicator (GSMXCN4G in Canada) easily connects to your security system's control panel and
sends alarms and messages to AlarmNet for subsequent transfer to the central monitoring station. The communicator can
be mounted directly on the control panel or remotely.
NOTE: This guide addresses a simple installation using default programming values where possible. For detailed
information, refer to the GSMX4G / GSMXCN4G GSM Communicator Installation and Setup Guide. Due to
Honeywell's continuing effort to improve our products, your device may look slightly different than pictured.
• The GSMX4G requires an AlarmNet account. For new installations, please obtain the account information from the
central station prior to programming the communicator.
• The GSMX4G is for control panels that support GSM communicators (or LRR, Long Range Radio) and the ECP
communications bus. For control panels that do not support ECP, refer to the installation guide to use the 4204 mode.
• The control panel treats the communicator as an ECP device, so ensure to program the control panel with the
communicator's device address.
• The GSMX4G is for indoor use only. Standby current is 35mA, and Transmit Current is 250mA.
REMOTE SERVICES
Honeywell offers secure web based services that enable users to remotely monitor and control their security system. These web services enable
users to: monitor and control their security system from a website, receive email and text message notifications of system events, and use text
messages to control the system and receive confirmations.
Dealers can enroll their customers for "Remote Services" by using the AlarmNet Direct website. Once enabled, the specific programming fields
associated with these features can be programmed into the communications device either remotely using the AlarmNet Direct website or locally using
the 7720P programming tool.
1. Mount and Wire the Communicator
SELECT A MOUNTING LOCATION
When choosing a suitable mounting location, understand that it must be
mounted indoors, and for best signal strength it should be mounted vertically.
Signal strength is very important for proper operation. For most installations,
mounting the unit on the control panel provides adequate signal strength and
we suggest that this method is tried first (especially if the control panel is not in
a basement location or in an area that contains large metal objects).
If the control panel location does not provide adequate signal strength, then the
communicator can be mounted remotely.
NOTE: The SIM in the GSMX4G must be ACTIVATED first in order for
signal strength to be determined. The SIM in the GSMXCN4G is already
activated.
ACTIVATE THE SIM
Go to:
https://services.alarmnet.com/AlarmNetDirect/
If you are not signed up for this service, click on "Dealer Signup" from the login
screen to set up your dealer account. You will be instructed how to proceed
upon completing the sign-up form. Only one sign-up per dealer is required.
Once an initial user is established, additional logins may be created.
Log in and follow the on-screen prompts. At this time only activate the SIM so
signal strength may be checked. DO NOT register the communicator at this
time. Please have the following information available to activate the SIM:
• MAC ID and MAC CRC number (located on the box and inside the
communicator).
You may log out of the AlarmNet Direct website.
VERIFY SATISFACTORY SIGNAL STRENGTH
In this procedure you will temporarily power up the communicator to check for
satisfactory signal strength. You can power it from a 12V battery or from the
control panel's AUX PWR terminals. In buildings where reception may be a
problem, powering from a battery would allow the communicator to be portable.
The following procedure assumes the control panel will be used for power.
1. Ensure power to the control panel (both AC and battery) is off. Open the
enclosure and connect the ECP cable to the communicator. Temporarily
attach the Black and Red wires to the GND and AUX PWR terminals of the
control panel. DO NOT connect the Yellow and Green wires at this time.
2. Turn power on and wait about one minute for the communicator to initialize.
Position the communicator near a suitable mounting position. Verify the
Minimum Signal Strength LED (green) is lit steadily.
3. Verify the signal strength remains steady for a few minutes, then
mark that mounting position. Turn power off.
Signal Strength
ON = Satisfactory
BLINKING = Marginal
OFF = Unsatisfactory
MOUNT THE COMMUNICATOR ON THE CONTROL PANEL
1. Ensure power to the control panel (both AC and battery) is off,
then remove a knockout on the top right.
2. Open the cover and remove the bottom knockout for the
threaded mount. Remove the Hole Cap attached to the plastic,
and snap it into the top of the enclosure.
3. Install the threaded mount so it snaps into the plastic retaining
tabs. Mount the communicator in the cabinet's knockout, and
fasten with the locking nut.
4. Connect the ECP cable to the communicator's circuit board and
thread the wires through the threaded mounting adapter.
Advertisement
Related Manuals for Honeywell GSMX4G
Summary of Contents for Honeywell GSMX4G
- Page 1 REMOTE SERVICES Honeywell offers secure web based services that enable users to remotely monitor and control their security system. These web services enable users to: monitor and control their security system from a website, receive email and text message notifications of system events, and use text messages to control the system and receive confirmations.
- Page 2 Using the 7720P Programming Tool to program and register: The communicator is now in full service and available for alarm reporting to the central 1. This procedure will program the GSMX4G for basic control panel station. communications. For advanced features and remote services refer to the product’s Installation and Setup guide.