Learning / Teaching A Master Tv Setup Using An Lt2002 Clone Programmer - LG 22LG3DDH Owner's Manual
Hide thumbs
Also See for 22LG3DDH:
- Owner's manual (93 pages) ,
- Setup manual (53 pages) ,
- Service manual (36 pages)
Table of Contents
Advertisement
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target
TVs, as this will damage the clone programmer and the PPV card.
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).
LT2002 Cloning Notes
Read the IMPORTANT CLONING
•
INFORMATION on page 27 before
beginning any cloning procedures.
A slow flashing green light indicates
•
that there are communication
problems between the TV and the
LT2002. If this is the case, check for
a damaged cable, poor contacts, or
other connection troubles.
If the status indicator is red, the
•
LT2002 batteries are low and should
be replaced. Install four (4) high-
quality alkaline AA batteries.
Learning and Teaching is only
•
possible between identical model TVs;
however, the LT2002 can store up to
three different Master TV Setups.
Learn Setup from Master TV
1. Ensure the Master TV is set up completely.
2. Tune/set the TV to an analog channel or Aux input, and then plug one end
of the MPI cable into the TV MPI port.
3. If there is a good connection after the LT2002 is connected to the TV MPI
port, "THE CLONE HAS CONTROL OF THE TV" message will appear on
the TV screen. Press any key on the Installer Remote to access the LT2002
Clone Selection Menu.
4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone
Selection Menu; then press OK (Enter) to proceed to the Memory Bank
Selection Menu.
5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in
which to store the Master Setup. Then, press OK (Enter).
Note: If you choose a Memory Bank that already has a Master device's
setup programmed into it, that setup will be overwritten by the new Master
TV Setup.
6. Verify the Learning setup information on the next screen, and then press
POWER to transfer the Master TV Setup into the selected Memory Bank on
the LT2002.
32
Antenna
or CATV
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION
XX
THE SW IS REVISION
XX
CLONE CLOCK = XX:XX
TV
CLOCK = XX:XX
- PRESS ANY KEY TO CONTINUE.
- DISCONNECT CLONE WHEN DONE.
(Continued on next page)
MPI
Cable
Ferrite Core
(TDK, ZCAT
2035-0930)
Connect cable to
TV MPI Jack and
follow on screen
Indicator
instructions
MPI
• green
• red
Blink pattern
• slow
• heartbeat power on
®
QuickSet II Programmer
LT2002
LT2002 Clone
Programmer
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
SAVE TV SETUP IN SELECTED
CLONE MEMORY
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-
TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
COPY SELECTED CLONE MEMORY
TO TV
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
- TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
Status
Reset
Color
battery ok
battery low
power on
no communications
communications ok
206-4190
- Quick Links:
- Other A/V Source Setup
- Input List
Hide quick links:
Advertisement
Chapters
Table of Contents
Troubleshooting
