Fm stereo sw/mw pll synthesized receiver (12 pages)
Summary of Contents for Sony ICF-SW07
Page 1
ICF-SW07 AN-LP2 SERVICE MANUAL US Model Canadian Model Ver 1.0 1999.02 AEP Model E Model Tourist Model Antenna Controller Antenna mdule AN-LP2 ICF-SW07 SPECIFICATIONS FM STEREO/SW/MW/LW PLL SYNTHESIZED RECEIVER MICROFILM...
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. – 2 –...
• Only the most recent version is supplied for replacing the Sony ROM. • A new Sony ROM is issued every year in October and the part No. suffix is also changed. • A new updated Sony ROM is issued every year so is not usually kept in stock.
SECTION 3 DISASSEMBLY The equipment can be removed using the following procedure. <RADIO SECTION> Cabinet (Lower) ASSY Main board Chassis ASSY Cabinet ASSY Key board Microcomputer board <ANTENNA CONTROLLER SECTION> Cabinet (Front), Reel ASSY Cabinet (Rear), Reel board, Control board Note : Follow the disassembly procedure in the numerical order given.
3-2. CHASSIS ASSY 2 Screw (1.4x4) Main board Chassis ASSY 4 Remove solder Black Flexible board Brown Cabinet ASSY Caution A portion of the chassis and cabinet ASSY are joined by adhesive sheet so use caution during removal. 3-3. MAIN BOARD Terminal (+), Battery 5 Flexible board (Key board:CN701)
SECTION 4 ELECTRICAL ADJUSTMENTS AM SECTION 1 st IF Adjustment 0dB=1µV BAND : AM VOLUME control : as required 2nd LOCAL Adjustment Setup : BAND : AM VOLUME control : as required Put the lead-wire AM RF SSG Connection Points : antenna close to the set.
Page 30
SW FREQUENCY Adjustment Procedure : BAND : AM 1. Align the set with the frequency of the AM RF signal generator VOLUME control : as required shown on the table below. Connection Points : 2. Align RV401 - RV412 for each band meter band until the high- est reading is obtained on the level meter.
Page 31
FM SECTION FM TRACKING Adjustment Note : This adjustment should be performed after the remove Rod Antenna (ANT102). FM FREQUENCY COVERAGE Adjustment This adjustment should be performed after the FM FRE- BAND : FM QUENCY COVERAGE ADJUSTMENT. VOLUME control : as required Connection Points : Digital BAND : FM...
Page 32
FM STEREO Adjustment SD Adjustment BAND : FM BAND : FM ST • MONO switch : ST VOLUME control : as required VOLUME control : as required Connection Points : Connection Points : FM RF SSG servicing tool DC5V TP(ANT) 2.4k Ω...
Page 33
FM 100MHz Adjustment MICROCOMPUTER SECTION BAND : FM VOLUME control : as required 4MHz SYSTEM CLOCK Adjustment Connection Points : BAND : AM servicing tool VOLUME control : as required Connection Points : DC5V 2.4k Ω servicing tool frequency 0.01 µ F DC5V 2.4k Ω...
SECTION 5 DIAGRAMS 5-1. EXPLANATION OF IC TERMINALS IC402 µPD17072GB-556-1A7 (PLL SYNTHESIZER CONTROL) Pin No. Pin name Description ROD/BAR ROD/BAR antenna select output. “H” : BAR, “L” : ROD AM/FM AM/FM select output. “H” : AM, “L” : FM ENV/PSN ENV/PSN select output.
Page 35
IC501 µPD753017AGK-717-BE9 (MAIN SYSTEM CONTROL, LCD DRIVE) Pin No. Pin name Description 1 – 12 S12 – 23 LCD segment signal output. 13 – 16 ––––– – Not used (OPEN). XTAL-CTL Level shift control output for system clock. BEEP-CTL Beep signal control ouptut. IF-POWER IF B+ ON/OFF control output.
Page 36
– Not used (OPEN). 68 – 80 S0 – S11 LCD segment signal output. Circuit Boards Location MICROCOMPUTER board ROM board REEL board MAIN board KEY board CONTROL board ANTENNA board ICF-SW07 ANTENNA CONTROLLER SW LOOP ANTENNA – 36 –...
ICF-SW07 5-4. SCHEMATIC DIAGRAM (MAIN SECTION) Refer to page 63 for IC Block Diagrams. Waveforms (MAIN Section) Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
ICF-SW07 5-9. PRINTED WIRING BOARDS (ANTENNA SECTION) 5-10. SCHEMATIC DIAGRAM (ANTENNA SECTION) Semiconductor Location Ref. No. Location D901 B-11 D902 IC901 C-10 Q901 Q902 B-10 Q903 B-10 • Voltages are dc with respect to ground under no-signal Note: (detuned) conditions.
Page 42
IC Block Diagrams (MAIN Section) IC403 LA5002M IC201 CXA1376AM WAKE REF. VOLTAGE AM FE FM FE ERROR CONTROL AM IF SYNC DE ENV DET FM DEM FM LIM AM VCO METER FM IF IC302 CXA1622M IC301 LA3335M GND1 P-GND1 OUT1 LAMP SYNC DECODER...
SECTION 6 EXPLODED VIEWS NOTE : • -XX, -X mean standardized parts, so they • The mechanical parts with no reference may have some difference from the original number in the exploded views are not one. supplied • Items marked “ * ”are not stocked since they •...
SECTION 7 ANTENNA CONTROL ELECTRICAL PARTS LIST NOTE : • Due to standardization, replacements in the • SEMICONDUCTORS In each case, u : µ , for example : The components identified by mark ! parts list may be different from the parts uA..