The ( ) SRS (SOUND RETRIEVAL SYSTEM) is manufac- Supplied Accessories tured by Sony Corporation under license from SRS Labs, Remote commander (w/2 size AA (R6) batteries) Inc. It is covered by U.S. Patent No. 4,748,669. Other U.S. and foreign patents pending.
SONT D'UNEIMPORTANCE CRITIQUE POUR LA SECURITE DU FONCTIONNEMENT. THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE NUMERO DE NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN PIECE EST INDIQUE DANS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS...
Page 4
KV-32S65/35S65 SAFETY CHECK-OUT After correcting the original service problem, perform the LEAKAGE TEST following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth ground customer: and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampere).
Basic Set Up This section teaches you the basic skills • If you will not be using the TV for several Cable box and cable to view scrambled channels (KV-32S65, 32V65, 35S65, Model needed to operate your new TV. It shows...
Page 6
Connecting and Installing the TV (continued) Disconnect all power sources before making any connections. Disconnect all power sources before making any connections. VCR Connections DBS Connections Cable/Antenna (Rear of TV) (Rear of TV) VCR must be connected and For optimum picture quality, use S VIDEO Connecting an antenna/cable TV turned on to operate PIP Connecting a DBS (Direct...
Toshiba Use the 0-9 buttons to key in the Marta Operating a VCR Buttons on the • The code numbers for Sony VCR's are assigned at the Operating an MDP Buttons on the remote Memorex 309, 335 manufacturer's code number from the...
• Check your CHANNEL FIX channel be correct. settings. (see page 26) If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Direct Response Center at 1-800-222-SONY (7669). (U.S. residents only)
KV-32S65/35S65 2-3. SERVICE POSITION 2 2 G Board 1 1 A Board ANODE-CAP REMOVAL WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electrical shock, discharge CRT before attempting to remove the anode cap. Short between anode and coated earth ground strap of CRT.
KV-32S65/35S65 2-4-1. PICTURE TUBE REMOVAL (KV-32S65) WARNING -- Before removing anode cap: Four screws (Tapping screw 7) G board High voltage remains in the CRT even after the power is disconnected. Chassis To avoid electrical shock, discharge CRT before attempting to remove the anode Picture tube cap.
KV-32S65/35S65 SECTION 3 SET-UP ADJUSTMENTS Perform the adjustments in order as follows: The following adjustments should be made when a complete realignment is required or a new picture 1. Beam Landing tube is installed. 2. Convergence 3. Focus These adjustments should be performed with rated 4.
KV-32S65/35S65 3-2. CONVERGENCE Preparation: • Before starting, perform FOCUS, V. LIN and V. SIZE adjustments. • Set BRIGHTNESS control to minimum. • Input dot pattern. Operation of BMC (Hexapole) Magnet (1) Vertical and Horizontal Static Convergence The respective dot positions resulting from moving each magnet interact, so perform adjustment while tracking.
KV-32S65/35S65 3-4. SCREEN (G2) ( 2 ) Dynamic Convergence Adjustment Input dot pattern from the pattern generator. • Before starting, perform Horizontal and Vertical Static Convergence Adjustment. Set the PICTURE and BRIGHT controls at normal. Slightly loosen deflection yoke screw.
KV-32S65/35S65 SECTION 4 SAFETY RELATED ADJUSTMENTS R530, R531 CONFIRMATION METHOD (HOLD-DOWN CONFIRMATION) AND READJUSTMENTS Always perform the following adjustments when replacing the following components marked with a ] mark on the schematic diagram: dejital digital multimeter multimeter A BOARD: IC351, IC501, D519, D520, D521, C531,...
KV-32S65/35S65 SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENT BY REMOTE COMMANDER Use Remote Commander (RM-Y167) to perform the following circuit adjustments: NOTE : Test Equipment Required: 1. Pattern Generator 2. Frequency Counter 3. Digital Multimeter 4. Audio OSC (1) Method of Setting the Service 8.
Page 17
KV-32S65/35S65 (4) Service Data Register Description Data Adj/Fix Initial Average Data Comments Name Range Data 32" 35" VP CXA2095S VPOS V-Position 0-63 0:Down, 63:Up VSIZ V-Size 0-63 0:Min, 63:Max VCOM V-Compensation 0:Min, 3:Max VLIN V-Linearity 0-15 0:Min, 15:Max VSCO S-Correction...
Page 18
KV-32S65/35S65 Service Data (cont.) Register Description Data Adj/Fix Initial Average Data Comments Name Range Data 32" 35" PI SDA9288 PYSD Select Delay 0-15 Fix by P-bd 0:Right, 15:Left PIPH PIP H-position 0-127 0:Right, 127:Left PIPV PIP V-position 0-63 0:Up, 63:Down...
Page 19
KV-32S65/35S65 Service Data (cont.) Register Description Data Adj/Fix Initial Average Data Comments Name Range Data 32" 35" ID MAP ID-0 ID-0 (Language/Color Systems) 0-255 Fix by model See ID map ID-1 ID-1 (Input/Output Conifguration) 0-255 Fix by model See ID map...
Page 20
KV-32S65/35S65 SUB BRIGHT ADJUSTMENT (SBRT) 10. Return the following back to normal after adjustment. 1. Set to Service adjustment Mode. PICTURE ... MAX COLOR ... CENTER 2.
Page 21
KV-32S65/35S65 PIN AMP (PAMP) V. SIZE ADJUSTMENT ( VSIZ) 1. Input a cross-hatch signal. 2. Set to Service adjustment mode. 3. Select VSIZ with PIN PHASE (PPHA) 4.Adjust with for the best vertical size. 5.Write into the memory by pressing then V.
KV-32S65/35S65 6-2. CIRCUIT BOARDS LOCATION (KV-35S65 only) (KV-35S65 only) (KV-32S65 only) 6-3. PRINTED WRING BOARDS AND SCHEMATIC DIAGRAMS • Readings are taken with a color-bar signal input. Note: • Readings are taken with a 10MΩ digital multimeter. • Voltages are DC with respect to ground unless otherwise noted.
Page 23
O-BBE PIN33 SCLK FROM A BOARD MUTE MUTE (1/2) FROM SDATA Q461,642 A BOARD (1/2) AUDIO AMP (VAR/FIX) IC101 J233 VAR-L VARIABLE VAR-R Block Diagram KV-32S65/36S65 Manual #: 9-965-845-01 AUDIO AMP (2/2) (SRS, AV-SW, AV-TERMINAL) SYSTEM CONTROL B-SV6747< AA2D98-M#2S> -BD.
Page 31
KV-32S65/35S65 #9-965-845-01 AV BOARD TRANSISTOR AV BOARD IC VOLTAGE LIST VOLTAGE LIST IC1902 Q101 volt Q103 Q104 Q105 0.80 -0.1 Q860 0.68 Q862 0.70 0.05 Q864 Q1901 Q1902 -0.1 Q1905 0.80 All voltages are in V IC1901 volt All voltages are in V...
KV-32S65/35S65 #9-965-845-01 B BOARD IC VOLTAGE LIST B BOARD TRANSISTOR IC3501 IC3502 VOLTAGE LIST volt volt Q3501 Q3502 Q3503 Q3504 Q3505 Q3506 Q3507 Q3509 Q3510 Q3516 IC3503 Q3555 volt All voltages are in V All voltages are in V...
Page 38
C BOARD IC VOLTAGE LIST C BOARD TRANSISTOR VOLTAGE LIST IC1701 volt Q1790 All voltages are in V 203.1 136.7 146.2 KV-32S65/35S65 #9-965-845-01 All voltages are in V...
Page 47
KV-32S65/35S65 #9-965-845-01 P BOARD IC VOLTAGE LIST IC3302 IC3304 volt volt P BOARD TRANSISTOR VOLTAGE LIST IC3303 Q3301 volt Q3302 Q3306 Q3310 Q3312 Q3314 All voltages are in V -2.9 All voltages are in V...
KV-32S65/35S65 #9-965-845-01 UV BOARD UV BOARD TRANSISTOR UV BOARD IC LOCATOR LIST VOLTAGE LIST VOLTAGE LIST CONNECTOR IC100 CN261 IC100 Q100 volt CN262 IC101 Q101 CN263 IC102 Q243 CN264 IC103 Q262 CN265 IC261 Q263 DIODE TRANSISTOR Q265 D100 Q100 All voltages are in V...
Page 52
VOLTAGE LIST VOLTAGE LIST IC961 Q943 volt Q944 Q945 Q946 133.7 67.2 134.2 Q947 67.3 Q963 Q965 Q966 Q981 IC981 All voltages are in V volt Q962 11.2 All voltages are in V All voltages are in V KV-32S65/35S65 #9-965-845-01...
• Items marked with an asterisk " * " are not stocked since they are portant le numero specifie. seldom required for routine service. Some delay should be anticipated when ordering these items. 7-1. CHASSIS (KV-32S65) 7-685-648-79 SCREW +BVTP 3X12 4-388-477-01 SCREW 3X16 TAPPING, WASHER REF.NO. PART NO.
P BOARD COMPLETE PARTS LIST (All Models) ......................... 71 UV BOARD COMPLETE PARTS LIST (All Models) ......................72 WA BOARD COMPLETE PARTS LIST (KV-35S65 only) ....................... 74 WB BOARD COMPLETE PARTS LIST (KV-32S65 only) ...................... 75 ACCESSORIES AND PACKAGING (All Models) ........................76 — 57 —...
Page 60
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified Les composants identifies per COMMON PARTS LIST un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.
Page 61
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified Les composants identifies per COMMON PARTS LIST un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.
Page 62
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical COMMON PARTS LIST symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.
Page 63
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified by in this The components identified manual have been carefully factory-selected with shading and a critical COMMON PARTS LIST for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation.
Page 64
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified Les composants identifies per COMMON PARTS LIST un trame et une marque ¡ ¡ ¡ ¡ ¡ sont with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.
Page 65
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified by in this The components identified manual have been carefully factory-selected VARIANT PARTS LIST with shading and a critical for each set in order to satisfy regulations re- symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for garding X-ray radiation.
Page 66
KV-32S65/35S65 #9-965-845-01 Note: Note: AV B The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont COMPLETE PARTS LIST with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.
Page 70
KV-32S65/35S65 #9-965-845-01 Note: Note: The components identified Les composants identifies per un trame et une marque ¡ ¡ ¡ ¡ ¡ sont COMPLETE PARTS LIST with shading and a critical symbol ( ¡ ¡ ¡ ¡ ¡ ) are critical for critiques pout la securite.