Page 2
ELECTRIC UNIT (X34- ) ∗ IC240 SW5V DSP5V ∗ IC241 ∗ DME1 Q440,442, MEMORY ∗ 450,451, J420 ∗ PRE OUT CD MECHA SERVO IC260 460,462 (FRONT) BU5V ∗ X92-6320-00 PRE OUT (W/O USB MODEL) MUTE (REAR) Q441,461 PRE OUT SW MUTE (SW) X92-6360-00 IC200...
Page 3
CD PLAYER UNIT (X32-6260-00) MOTHER BOARD DPU1 (X34- ) SIGNAL A/B/C/E/F CD SI DATA S CD SO REQ A LEVEL BUCK CD CLK MSTOP SHIFT MSTOP CD REQ DSP REQ MRST MRST RF AMP SERVO SRAMSTB CD SRAMSTB PROCESSOR CD RST Z DET ZDET IN DATA M...
Page 4
KDC-BT6544U/BT6544UY /BT7043U/BT742U COMPONENTS DESCRIPTION ● ELECTRIC UNIT (X34-629x-xx) Ref. No. Application / Function Operation / Condition / Compatibility IC10 Audio 8V REF / Power Supply Outputs 1.27V. IC70 Digital AVR for Panel & USB Switching regulator for USB&VBUS and FDC (5V). IC150 Power Control SW USB power control switch with over current detection and protection.
KDC-BT6544U/BT6544UY /BT7043U/BT742U COMPONENTS DESCRIPTION ● SWITCH UNIT (X16-6500-21) Ref. No. Application / Function Operation / Condition / Compatibility Remote Controller Remote control receiver. PAN5V When the base goes Hi, PAN5V is supplied for IC2. Key Scan Timing Adjustment When the base goes Hi, key scan starts. PAN5V When the base of Q5 goes Hi, PAN5V is supplied for IC2.
KDC-BT6544U/BT6544UY /BT7043U/BT742U MICROCOMPUTER’S TERMINAL DESCRIPTION ● SYSTEM μ-COM: IC302 on X34- (ELECTRIC UNIT) Truth Value Pin No. Pin Name Application Processing / Operation / Description Table External remote control input and panel remote REMO control input LX REQ M Communication request to slave unit B SYS DATA Serial output to Bolero B MECHA DATA...
Page 7
KDC-BT6544U/BT6544UY /BT7043U/BT742U MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Value Pin No. Pin Name Application Processing / Operation / Description Table Detects pulse width ROTARY CCW VOL key detection (Counterclockwise) TDF: 15-pulse/360°, 2-click/1-pulse Not used Output L fi xed VFD CS VFD control request H: Possible to transfer VFD data BT RST Bluetooth module reset...
Page 8
KDC-BT6544U/BT6544UY /BT7043U/BT742U MICROCOMPUTER’S TERMINAL DESCRIPTION Truth Value Pin No. Pin Name Application Processing / Operation / Description Table ST DC DET Wrong connection detection E2P SDA I/O E2PROM I2C data input/output E2P SCL I/O E2PROM I2C clock input/output DC DET DC offset detection MUTE AFS I/O AFS mute...
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Display description Description of display Description ÷ ÷ ÷ ÷ ÷ ÷ ÷ A symbol “■” in the key column indicates that the key should be pressed and held for 1 second or longer. ■ Key layout TEL/ ←...
Page 10
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE Description Default values System Q/dB EQ NATURAL (FLAT) Simple DSP STANDBY (FLAT) Simple DSP BYPASS (Set up the path that does not go through the DSP) Beep Goes on (i.e., beeps) when the key is pressed briefl y Preout Rear ■...
Page 11
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE • Version and service information display (Sub-mode) * When “Version and service information display” is selected, “Destination terminal condition display” will be opened as default display. Description of display Description Destination “TYPE” indicates system μ-com (IC302) destination, terminal and shows real-time condition of the destination 2 : 1...
Page 12
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE • CD information display mode (Sub-mode) Description of display Description Mechanism error log 1 (Latest) XX: Error number. “– –” is displayed in case there is no error. CD mecha- Mechanism error log 2 (Latest) nism error XX: Error number.
Page 13
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Test mode specifi cations in TUNER source Error is found in front-end (A1), etc. if indications below is displayed while in tuner source. Status Display Description Front-end (A48x) E2PROM data Front-end (A48x) E2PROM is still the default error (unspecifi...
Page 14
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE • FST adjustment mode Perform FST soft-mute adjustment. Note To enter into FST adjustment mode (Press and hold the key for 1 second) ■ In FM, the frequency changes to 98.3MHz Operations in the FST adjustment mode are as follows: Description of display Description / Soft-mute...
Page 15
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Test mode specifi cations in CD source Display mode default: P-Time • Procedure in CD-DA media (KTD-02A) Display Description Every time pressed, jumps to the track shown below. No.9 → No.15 → No.10 → No.11 → No.12 → No.13 → No.22 Track up procedure →...
Page 16
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Audio-related test mode Procedure Note Enter the audio adjustment mode (The default items shown are different from model with DSP to model without DSP) [Model with DSP] (Destination “K” and “E”) When DUAL ZONE is ON: BYPASS→DUAL ZONE→FADER→BALANCE→R-VOLUME→V-OFFSET When DUAL ZONE is OFF: BYPASS→DUAL ZONE→FADER→BALANCE→SUB-W→V-OFFSET ■...
Page 17
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Backup current measurement Procedure Note MUTE terminal is OFF after 2 seconds, not after 15 seconds. While ACC OFF (Back Up ON), Reset (During this time, the CD mechanism does not function.) ■ Switching of Preout Procedure Note Press and hold [TEL/TI/AUTO] key in the Standby source...
Page 18
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ Clearing DC offset error detection data (E2PROM data clearing) Procedure Note Resetting while [PLAY/PAUSE] + [FAV] is being pressed Entering DC offset error display mode. While “----” is displayed, power can be ON. Even if the DC offset error detection is running, it shall be possible to move to this condition. This mode is cleared when the unit is reset.
Page 19
KDC-BT6544U/BT6544UY /BT7043U/BT742U TEST MODE ■ ROM data transfer * This function is shown in the MENU only when the source is STANDBY and thus in reality it is operational only in the case of STANDBY source. Procedure Display Description While pressing and holding [SEARCH] key and [SRC] All lights ON.
KDC-BT6544U/BT6544UY /BT7043U/BT742U ROM DATA TRANSFER PROCESSES When replacing front-end (A48x) of mother unit (X34-), or Forced Power OFF information (For maintenance) when adding or replacing ROM correction (program cor- Serial number (For maintenance) rection with ROM IC (IC300)), the following activities are E2PROM data check data (For internal check) required.
Page 21
KDC-BT6544U/BT6544UY /BT7043U/BT742U ROM DATA TRANSFER PROCESSES Turn power on. Install new front-end (A48x). Press and hold the [1] and [3] keys and press reset button. No ROM correction or other data status. (Enter the system in the test mode.) Press [B.BOOST] key. (ROM data System enters data trans- fer mode.) Mother unit (X34-) Press...
Page 22
KDC-BT6544U/BT6544UY /BT7043U/BT742U ROM DATA TRANSFER PROCESSES 4. In case of applying a new ROM correction when front- Turn power on. end (A48x) is replaced (There is ROM correction data.) Press and hold the [1] and [3] keys, press reset button. (Enter 5.
Page 23
KDC-BT6544U/BT6544UY /BT7043U/BT742U ROM DATA TRANSFER PROCESSES Press key. (Exit ROM data transfer mode.) Turn power on. Turn power off. Press and hold the [1] and [3] keys press reset button. (Enter the system in the test mode.) Remove front-end (A48x). Press [B.BOOST] key.
KDC-BT6544U/BT6544UY /BT7043U/BT742U INSTALLER MEMORY SPECIFICATIONS At specialists (or specialty stores), when the installer sends • The contents read out by the call key shall be refl ected the vehicle back to the user, they may make the store-rec- only to the current source at the time→EQ curve is ommended audio confi...
Page 25
KDC-BT6544U/BT6544UY /BT7043U/BT742U PC BOARD PC BOARD (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) SWITCH UNIT SWITCH UNIT X16-6500-21 (J76-0568-02) X16-6500-21 (J76-0568-02) VCC VOUT TP30 MIC-N R101 D101 MIC-P R102 D102 PAN-DET RTRY-CW R103 D103 RTRY-CCW R104 D104 R105 REMO D105 D106 R106 VFD-CE CP10...
Page 30
KDC-BT6544U/BT6544UY /BT7043U/BT742U PC BOARD (COMPONENT SIDE VIEW) X32 B/2 12EJE ORG LOS GRE GND BLU R105 CD PLAYER UNIT R102 X32-6260-00 A/2 (J76-0572-02) AGND CD RST IOP+ BUCK A3.3V R119 R177 CP11 R101 R121 12EJE SW R171 R118 LOS SW R117 SRAMSTB BU5V...
Page 31
KDC-BT6544U/BT6544UY /BT7043U/BT742U PC BOARD (FOIL SIDE VIEW) X32 B/2 CD PLAYER UNIT X32-6260-00 A/2 (J76-0572-02) R127 R120 R128 CP15 R166 CP12 C102 R167 R68 R69 R132 R131 X32-6260-00 Ref. No. Address Refer to the schematic diagram for the values of resistors and capacitors.
Page 32
KDC-BT6544U/BT6544UY /BT7043U/BT742U PRE OUT ANT. ∗ ELECTRIC UNIT (X34-6xxx-xx) J420 W481 TP480 FRONT-END A480: For European models ∗ A480 A481: For other models RFGND C482 ANTINPUT 0.01 TP496 Q440,442 Q450,451 Q460,462 PRE OUT PRE OUT PRE OUT AM+B MUTE SW MUTE SW MUTE SW OSCGND...
Page 33
KDC-BT6544U/BT6544UY /BT7043U/BT742U TP315 TP317 L300 BU5V-1 4.7uH IC301 ∗ ∗ R325 R330 TP316 BU5V 100K 100K VOUT PON5V C306 5.0V SYSTEM u-COM RESET CP306 CONTROL 4.7K R300 2.2M R315 2.2K REMO ∗ R316 100 LX REQ M 0V or 1.6V or 0-5.0V 5.0V P CON...
Page 37
KDC-BT6544U/BT6544UY /BT7043U/BT742U SWITCH UNIT (X16-6xxx-xx) 1.1V CP14 0.01 TP31 Q22-24 GRID REVERSING BLUETOOTH DRIVER D GND ∗ KEY SCAN KEY MATRIX (09TDF BASIC) MIC P TIMING COL1 COL2 COL3 COL4 COL5 COL6 MIC N ADJUSTMENT ROW1 ROW2 FAVORITE SEARCH AUTO TP24 PAN DET EJECT...
Page 38
KDC-BT6544U/BT6544UY /BT7043U/BT742U (1G-3G) (3G) (2G) (1G) col5 col3 col1 col3 col1 col3 col1 col6 col4 col2 col4 col2 col4 col2 (1G) col3 col3 col3 col1 col1 col1 (1G-3G) CAUTION : For continued safety, re place safe ty critical com po nents only with manufacturer’s rec om mend ed parts (refer to parts list).
Page 39
KDC-BT6544U/BT6544UY /BT7043U/BT742U CD PLAYER UNIT (X32-6260-00) (A/2) MECHA. (X92- ) SLED OUT /LOAD 4ch BTL DRIVER TP123 TP128 1.7V ZDET 7.5V POWVCC1 R132 100 TP124 LOADING & POWGND1 SLED IN SLED TP127 /EJECT SLIN MOTOR VO1- R131 200K LDIN SPDL+ VO1+ TP122 BIASSW...
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST ✽ New parts Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. Desti- Desti- Ref. No. Parts No. Description Ref.
Page 45
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST SWITCH UNIT (X16-6500-21) Desti- Desti- Ref. No. Parts No. Description Ref. No. Parts No. Description nation nation RK73GB2A223J CHIP R J 1/10W CK73GB1C104K CHIP C 0.10UF CK73FB0J106K CHIP C 10UF R117,118 RK73GB2A103J CHIP R J 1/10W R120 RK73GB2A103J CHIP R...
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST CD PLAYER UNIT (X32-6260-00) IN CD MECHA Desti- Desti- Ref. No. Parts No. Description Ref. No. Parts No. Description nation nation RK73GB2A153J CHIP R J 1/10W RUE003N02 RK73GB2A100J CHIP R J 1/10W 2SA1577 TRANSISTOR RK73GB2A153J CHIP R J 1/10W DTC114YUA DIGITAL TRANSISTOR...
Page 47
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST ELECTRIC UNIT (X34-629x-xx) Desti- Desti- Ref. No. Parts No. Description Ref. No. Parts No. Description nation nation C261 CK73GB1A474K CHIP C 0.47UF C615 CK73FB1H334K CHIP C 0.33UF C616 CD04BK0J331M ELECTRO 330UF 6.3WV C262,263 CK73GB1A105K CHIP C 1.0UF C264 CK73GB1A474K...
Page 48
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST ELECTRIC UNIT (X34-629x-xx) Desti- Desti- Ref. No. Parts No. Description Ref. No. Parts No. Description nation nation RK73GB2A104J CHIP R 100K J 1/10W R321 RK73GB2A104J CHIP R 100K J 1/10W R323 RK73GB2A104J CHIP R 100K J 1/10W RK73FB2B203J CHIP R J 1/8W...
Page 49
KDC-BT6544U/BT6544UY /BT7043U/BT742U PARTS LIST ELECTRIC UNIT (X34-629x-xx) Desti- Desti- Ref. No. Parts No. Description Ref. No. Parts No. Description nation nation R462,463 RK73GB2A223J CHIP R J 1/10W D532-534 UDZW6.8(B) ZENER DIODE R464 RK73FB2B181J CHIP R J 1/8W D600 UDZW6.2(B) ZENER DIODE R465 RK73GB2A331J CHIP R...
KDC-BT6544U/BT6544UY /BT7043U/BT742U SPECIFICATIONS ■ Models for destination “K” Auxiliary input Frequency response (±1dB) ......20Hz~20kHz FM tuner section Input Maximum Voltage ..........1200mV Frequency range (200kHz space) ..87.9MHz~107.9MHz Input Impedance ............100kΩ Usable sensitivity (S/N=30dB) ....9.3dBf (0.8μV/75Ω) General Quieting Sensitivity (S/N=50dB) ....15.2dBf (1.6μV/75Ω) Frequency response (±3.0dB) ......30Hz~15kHz Operating voltage (10.5~16V allowable) .......
Page 52
Output Power ..+4dBm (MAX), 0dBm (AVE) Power Class 2 Installation Size (W x H x D) .....182 x 53 x 155mm Weight ................1.2kg KENWOOD follows a policy of continuous advancements DANGER: in development. For this reason specifi cations may be Please do not look at the laser beam directly during changed without notice.