hit counter script
IBM pSeries 7311 D10 Service Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Server
  5. eserver pSeries 7311 D10
  6. Service manual
IBM pSeries 7311 D10 Service Manual

IBM pSeries 7311 D10 Service Manual

Hide thumbs Also See for pSeries 7311 D10:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
ERserver
pSeries 7311 Model D10 and Model D20
Service Guide
SA38-0627-01

Advertisement

Table of Contents
loading

Related Manuals for IBM pSeries 7311 D10

Summary of Contents for IBM pSeries 7311 D10

  • Page 1 ERserver pSeries 7311 Model D10 and Model D20 Service Guide SA38-0627-01...
  • Page 3 ERserver pSeries 7311 Model D10 and Model D20 Service Guide SA38-0627-01...
  • Page 4 © International Business Machines Corporation, 2002, 2003. All rights reserved. Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth is GSA ADP Schedule Contract with IBM Corp.

  • Page 5: Table Of Contents

    Contents Safety Notices ....... . . vii Rack Safety Instructions ......vii Electrical Safety .
  • Page 6 Checkpoints ........40 Error Code to FRU Index .
  • Page 7 Component LEDs ....... . 173 Resetting the LEDs ......176 Appendix A.
  • Page 8 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...

  • Page 9: Safety Notices

    Safety Notices A danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury. Danger notices appear on the following pages: v viii v 41 v 150 A caution notice indicates the presence of a hazard that has the potential of causing moderate or minor personal injury.

  • Page 10: Electrical Safety

    Electrical Safety Observe the following safety instructions any time you are connecting or disconnecting devices attached to the workstation. In the system you are about to setup or service: v The ac power interface connector is considered the main power disconnect device. v This system has redundant power supply capabilities, meaning that it has the ability to have two power supplies running simultaneously in the same system unit.

  • Page 11: Laser Safety Information

    CAUTION: All IBM laser modules are designed so that there is never any human access to laser radiation above a class 1 level during normal operation, user maintenance, or prescribed service conditions. Data processing environments can contain equipment transmitting on system links with laser modules that operate at greater than class 1 power levels.
  • Page 12 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...

  • Page 13: Data Integrity And Verification

    Data Integrity and Verification IBM computer systems contain mechanisms designed to reduce the possibility of undetected data corruption or loss. This risk, however, cannot be eliminated. Users who experience unplanned outages, system failures, power fluctuations or outages, or component failures must verify the accuracy of operations performed and data saved or transmitted by the system at or near the time of the outage or failure.
  • Page 14 Eserver pSeries 7311 Model D10 and Model D20 Service Guide...

  • Page 15: About This Book

    IBM Eserver pSeries and AIX Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Click hardware documentation Documentation for the AIX operating system is available at the IBM Eserver pSeries and AIX Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Click AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.

  • Page 16: Related Publications

    The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: v AIX v Electronic Service Agent v Eserver v IBM v LANstreamer v PowerPC v pSeries v RS/6000 Other company, product, and service names may be trademarks or service marks of others.

  • Page 17: Chapter 1. Reference Information

    Chapter 1. Reference Information This chapter provides reference information for the Model D10 and Model D20 I/O subsystems. pSeries 7311 Model D10 Overview The Model D10 is a 19-inch, rack-mountable I/O subsystem that is attached to a processor subsystem drawer to extend the system’s capacity for I/O adapters. The I/O drawer includes redundant concurrently maintainable power and cooling.

  • Page 18: I/O Subsystem Pci-X Slot Led Definitions

    The following figure shows the rear view of the I/O subsystem. 1 PCI adapter slot 1 7 RIO bus adapter card Upper connector 0 Lower connector 1 2 PCI-X adapter slot 2 8 SPCN connector card 3 PCI-X adapter slot 3 9 Lower SPCN connector J16 4 PCI-X adapter slot 4 10 Upper SPCN connector J15...
  • Page 19 1 PCI Adapter Cassette 2 Power LED (Green ) 3 Fault/Identify LED (Amber) Green PCI Slot Amber PCI Slot PCI Slot Definition LED Indication Power/Status On/No action The PCI slot power is on and the slot is operational. Do not remove or install adapters. Flashing On/Identify The PCI slot power is on, and the slot has been...

  • Page 20: D10 Power

    D10 Power The following figure shows the front view of the pocessor subsystem and two I/O subsystems. Each unit has two power supplies and two power cords for redundancy. Connect the power cords from one side of the system to one power distribution bus in the rack. Connect the power cords from the other side of the system to a different power distribution bus in the rack.
  • Page 21 The following figure shows the rear view of the processor subsystem and two I/O subsystems. 1 Model D10 I/O subsystem 3 Processor subsystem power supplies, power receptacles 2 7038 Model 6M2 processor 4 I/O backplane power (green) and subsystem fault/identify (amber) LEDs D10 Cooling Fans mounted inside each I/O subsystem power supply and an additional fan mounted on the front of the subsystem provide cooling.

  • Page 22: Subsystem Positioning And Cabling

    Subsystem Positioning and Cabling I/O subsystems can be installed in a standard 19-inch EIA rack in any location. The cables that connect the subsystems allow some flexibility in drawer placement, but the I/O subsystems should be located above the processor subsystem to which they are connected in the same rack. Up to eight I/O subsystems can be connected to a processor subsystem.
  • Page 23 Four I/O Subsystems, Eight I/O Subsystems: The illustration on the left shows four I/O subsystems connected to the processor subsystem using one SPCN loop. The illustration on the right shows eight I/O subsystems connected to the processor subsystem using one SPCN loop. Processor Subsystem Connected to Four or Eight Model D10 I/O Subsystems: 1 Processor Subsystem 2 I/O Subsystem...
  • Page 24 One I/O Subsystem or Two I/O Subsystems: The illustration on the left shows one I/O subsystem drawer connected to the processor subsystem. The illustration on the right shows two I/O subsystem drawers connected to the system unit using one RIO loop. Processor Subsystem Connected to One or Two Model D10 I/O Subsystems: 1 Processor Subsystem 2 I/O Subsystem...
  • Page 25 1 Processor Subsystem 2 I/O Subsystem Chapter 1. Reference Information...

  • Page 26: Model D10 I/O Subsystem Locations

    Model D10 I/O Subsystem Locations This system uses physical location codes to provide mapping of the failing field replaceable units. The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.

  • Page 27: 7311 Model D10 I/O Subsystem Rear Locations

    7311 Model D10 I/O Subsystem Rear Locations 1 PCI adapter slot 1 7 RIO bus adapter card U0.dd-P1-I1 U0.dd-P1.1 2 PCI-X adapter slot 2 8 SPCN connector card U0.dd-P1-I2 U0.dd-P1 (part of the I/O backplane FRU) 3 PCI-X adapter slot 3 9 SPCN Connector 2/J16 U0.dd-P1-I3 U0.ddP1/Q5...

  • Page 28: Model D10 I/O Backplane Locations

    Model D10 I/O Backplane Locations The following illustration of the I/O backplane identifies the primary connectors used in your subsystem. 1 PCI adapter connector 1 7 SPCN connector 2 PCI-X adapter connector 2 8 VPD module 3 PCI-X adapter connector 3 9 VPD module pin 1 orientation 4 PCI-X adapter connector 4 10 RIO bus adapter connector...

  • Page 29: Model D10 I/O Subsystem Phb

    Model D10 I/O Subsystem PHB Each 7311 Model D10 I/O Subsystem has two PCI host bridges (PHBs) through which the PCI slots are connected. Slot Slot Characteristics 64-bit 5V, 33 MHz 64-bit 3.3V, 131.5 MHz 64-bit 3.3V, 131.5 MHz 64-bit 3.3V, 131.5 MHz 64-bit 3.3V, 131.5 MHz 64-bit 3.3V, 131.5 MHz Chapter 1.

  • Page 30: Model D10 Location Codes

    Model D10 Location Codes This system (processor subsystem and attached I/O subsystems) use physical location codes in conjunction with AIX location codes to provide mapping of failing field replaceable units (FRUs). The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.

  • Page 31: 7311 Model D10 I/O Subsystem Location Code Table

    7311 Model D10 I/O Subsystem Location Code Table The following table lists the location codes for a D10 I/O subsystem. The location code for the I/O subsystem connected to a system unit is U0.dd (where dd can be any number from 2 through 63). FRU Name Physical Location Code Model D10 I/O Drawer U0.dd (dd = any number from 2 through 63)

  • Page 32: Pseries 7311 Model D20 Overview

    pSeries 7311 Model D20 Overview The Model D20 is a 19-inch, rack-mountable I/O subsystem that is attached to a processor subsystem to extend the system’s capacity for I/O adapters and disk drives. The I/O subsystem includes redundant concurrently maintainable power and cooling. Seven PCI slots are available for PCI adapters.
  • Page 33 The green LEDs for the PCI-X adapter slots (viewed on the rear of the I/O subsystem) indicate the state of the PCI slot during removal and replacement of an adapter. PCI LED (Green) Indication PCI Slot Status Definition Slot power is Off. It is safe to remove or replace adapters.

  • Page 34: Model D20 Power

    Model D20 Power The Model D20 is standard with one power supply. If the customer wants redundant power in their I/O subsystem, an optional power supply can be ordered. Either power supply, in a Model D20 that is configured with two power supplies, can provide the necessary voltages and currents, independent of the other power supply.
  • Page 35 D20 I/O Subsystem Locations The system uses physical location codes to provide mapping of the failing field replaceable units. The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.
  • Page 36 Model D20 Power Supply Locations 1 Power Supplies 4 Green AC Power LED 2 Amber Fault/Identify LED 5 Power Supply Filler 3 Green DC Good LED 6 Model D20 I/O Drawer Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 37 Model D20 Blower Locations The following illustration identifies the I/O subsystem cooling blowers. Each blower has a green power LED and an amber identify LED located on the front blower housing. The green LED indicates that a blower has power and is operating correctly. The amber LED is in the identify state when blinking. 1 Green LED 4 Blower Connector 2 Amber LED...
  • Page 38 Model D20 I/O Backplane Locations The following illustration of the I/O backplane identifies the primary connectors used in your subsystem. Note: Before replacing the I/O backplane, note the position of pin 1 on the VPD module. 1 PCI-X Adapter Connector 1 11 Disk Drive Power Connector 2 PCI-X Adapter Connector 2 12 Cooling Blower Connector...
  • Page 39 Model D20 Reading the Operator Panel and I/O Backplane LEDs The following illustration shows the component location on the operator panel 1 Power-On LED 2 Attention LED 3 Operator Panel 4 Snap Buttons The following table defines each LEDs function on the operator panel. Number Component Name Component Description...
  • Page 40 Model D20 SCSI IDs and Bay Locations Index Bay Location Drive Name SCSI Bus ID 8 DB1 Hot-Plug Disk Drive 8 - DB1 9 DB1 Hot-Plug Disk Drive 9 - DB1 A DB1 Hot-Plug Disk Drive A - DB1 B DB1 Hot-Plug Disk Drive B - DB1 C DB1...
  • Page 41 Cabling the Model D20 to a pSeries 630 Model 6C4 The Model D20 subsystem can be installed in any location in a standard 19-inch EIA rack. The cables that connect the subsystems allow some flexibility in drawer placement. Up to two Model D20s can be connected to a pSeries 630 Model 6C4.
  • Page 42 RIO-2 (Remote Input Output) Cabling The following rules apply to RIO-2 cable connections: Notes: 1. To connect to a Model D20, you will be using the RIO-2 (Remote Input Output) and SPCN (System Power Control Network) connectors and cables. The RIO-2 and SPCN cables provide two functions, remote data bus connection, and power control.
  • Page 43 5. Lift the RIO-2 cable and cable connector into the bottom of the RIO-2 cable-support bracket. 1 Model 6C4 2 RIO-2 Cable-Support Bracket 3 Slide Portion of RIO-2 Cable-Support Bracket 4 RIO-2 Connector Support Lever 6. Pull the RIO-2 connector back until the connector is seated against the support hook. 7.
  • Page 44 Model 6C4 Attached to One I/O Drawer: 1 Model 6C4 2 Model D20 3 Cable from Model 6C4 Connector RIO-2 0 to Model D20 Connector RIO-2 0 4 Cable from Model 6C4 Connector RIO-2 1 to Model D20 Connector RIO-2 1 Model 6C4 Attached to Two I/O Drawers: 1 Model 6C4 2 Model D20 I/O Drawer...
  • Page 45 SPCN (System Power Control Network) Cabling The following figures provide cabling examples for all valid cabling configurations. Match your configuration to the correct figure and connect your SPCN cables as shown. Model 6C4 Attached to One I/O Drawer: 1 Model 6C4 2 Model D20 3 Cable from Model 6C4 Connector SPCN 2 to Model D20 Connector SPCN 4 (J16) 4 Cable from Model 6C4 Connector SPCN 1 to Model D20 Connector SPCN 3 (J15)
  • Page 46 Model D20 Internal Cabling 1 Cooling Blowers (Quantity 4) 6 Disk Drive Power Connector 2 Operator Panel 7 Disk Drive SPCN Connector 3 Disk Drive Backplanes 8 Disk Drive Power/Signal Cable 53P0416 4 Cooling Blower Cable 9 Operator Panel Connector 53P0419 5 Cooling Blower Connector 10 Operator Panel Cable...

  • Page 47: Model D20 Location Codes

    Model D20 Location Codes This system (processor subsystem and attached I/O subsystems) uses physical location codes in conjunction with AIX location codes to provide mapping of a failing field replaceable units (FRUs). The location codes are produced by the processor subsystem’s firmware and AIX. For information about how to read a location code, see the service guide for the processor subsystem to which your I/O subsystem is connected.

  • Page 48: Model D20 Location Code Table

    Model D20 Location Code Table The following table lists the location codes for a model D20 I/O subsystem. The location code for the I/O subsystem connected to a system unit is U0.dd (where dd can be any number from 2 through 63). FRU Name Physical Location Code Model D20 I/O Drawer U0.dd (dd = any number from 2 through 63)
  • Page 49 FRU Name Physical Location Code Cooling blower 4 U0.dd-F4 SPCN Connectors SPCN connector 1 U0.dd-P1/Q3 SPCN connector 2 U0.dd-P1/Q4 SPCN connector 3 U0.dd-P1/Q5 SPCN connector 4 U0.dd-P1/Q6 Rack Indicator Rack beacon (4–pin) U0.dd-P1/Q7 Operator Panel Operator panel U0.dd-L1 Temperature Sensor Temperature sensor (on operator panel) U0.dd-L1 Disk Drives Backplanes...

  • Page 50: Powering The System On And Off

    Powering the System On and Off Power for the I/O subsystems is controlled by the attached processor subsystem and the System Power Control Network (SPCN). For information about procedures to power the system on and off, refer to the service guide of the processor subsystem to which the I/O subsystem is attached.

  • Page 51: Model D10 And Model D20 Specifications

    Model D10 and Model D20 Specifications This section contains system specifications for both the Model D10 and Model D20 I/O subsystems. Model D10 Specifications Dimensions 7311-D10 Two 7311-D10s with Enclosure Height 170 mm (6.6 in) 178 mm (7.0 in) Width 220 mm (8.7 in) 445 mm (17.5 in) Depth...

  • Page 52: Model D20 Specifications

    Model D20 Specifications Dimensions Height 178 mm (7.0 in) Width 445 mm (17.5 in) Depth 610 mm (24.0 in) Maximum Weight 45.9kg (101 lbs) Electrical Power source loading (max.) 0.358 kVA Voltage range 100 to 240 V ac, V dc not supported Frequency 50 or 60 Hz Thermal output (typical)

  • Page 53: External Ac Power Cables

    External AC Power Cables To avoid electrical shock, a power cable with a grounded attachment plug is provided. Use only properly grounded outlets. Power cables used in the United States and Canada are listed by Underwriter’s Laboratories (UL) and certified by the Canadian Standards Association (CSA). These power cords consist of the following: v Electrical cables, Type SVT or SJT.

  • Page 54: Service Inspection Guide

    Service Inspection Guide Perform a service inspection on the system (processor subsystem and connected I/O subsystems) when: v The system is inspected for a maintenance agreement. v Service is requested and service has not recently been performed. v An alterations and attachments review is performed. v Changes have been made to the equipment that may affect the safe operation of the equipment.

  • Page 55: Chapter 2. Diagnostics And Maintenance Procedures

    Chapter 2. Diagnostics and Maintenance Procedures The system uses an integrated set of software diagnostic procedures to help isolate failing components and system maintenance. This book, along with the RS/6000 Eserver pSeries Diagnostic Information for Multiple Bus Systems, is the basis of the diagnostic procedures. Refer to the system service guide when running diagnostics on your I/O subsystem.

  • Page 56: Maintenance Analysis Procedures (Maps)

    Maintenance Analysis Procedures (MAPs) The maintenance analysis procedures (MAPs) provide the service representative a step-by-step procedure to analyze a problem with the system and I/O subsystem hardware. Be prepared to record code numbers and other data while using the MAPs. Because the Model D10 and Model D20 are subsystems, refer to your system’s service guide.

  • Page 57: Chapter 3. Removal And Replacement Procedures

    Chapter 3. Removal and Replacement Procedures Before performing any of the removal or replacement procedures in this chapter, read the following danger and caution notices. Safety Considerations Observe the following safety precautions anytime you work with these I/O subsystems. For the I/O subsystem you are about to setup or service: v The ac power interface connector is considered the main power disconnect device.

  • Page 58: Handling Static-Sensitive Devices

    Handling Static-Sensitive Devices Attention: Electronic boards and disk drives are sensitive to static electricity discharge. These devices are wrapped in antistatic bags to prevent this damage. Take the following precautions: v If you have an antistatic wrist strap available, use it while handling the device. v Do not remove the device from the antistatic bag until you are ready to install the device in the system.

  • Page 59: D10 Service Position

    D10 Service Position To perform a removal or replacement procedure that requires access to the inside of the I/O subsystem, the subsystem must be removed from the rack and placed on a stable work surface. To put the drawer into the service position, do the following: 1.

  • Page 60: D10 Covers

    D10 Covers Before performing the following procedure, read the “Safety Considerations” on page 41. Service Access Cover Removal To remove the service access cover, do the following: 1. Put the I/O subsystem into the service position as described in “D10 Service Position” on page 43. 2.

  • Page 61: Pci Adapters

    PCI Adapters Most PCI adapters can be removed and replaced, or installed in the system without turning off the power to the entire system. These adapters are referred to as hot-pluggable PCI adapters. Some adapters are not hot-pluggable and power must be removed from the system for adapter removal, replacement, or installation.
  • Page 62 1 PCI Adapter Cassette 2 Handle-release Lever Latch 3 Locking Bar 4 Handle Release Lever 5 Handle 6 PCI Adapter Tailstock Tab 7 Adapter Cassette Pull Tab Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 63 To remove a PCI adapter cassette, do the following: 1. Determine which PCI adapter cassette you are removing. 2. Disconnect any cables that are connected to the PCI adapter. 3. Press the handle release lever, then push the handle to the down position. See the following illustration.
  • Page 64 1 Locking Bar 2 PCI Adapter Tailstock Tab 3 Adapter Cassette Pull Tab 5. Position your index finger under the handle and push up the adapter tailstock tab. Grasp the adapter cassette pull tab with the other hand. Pull the PCI adapter cassette from the adapter slot by pulling on the adapter cassette pull tab.
  • Page 65 Replacing a PCI Adapter Cassette: Attention: Perform this procedure only when you are instructed to from “Removing a Non-Hot-Pluggable PCI Adapter” on page 51 or “Hot-Pluggable PCI Adapter” on page 52. Before you replace the PCI adapter cassette, check the following: v Before installing a PCI adapter cassette in the system, an adapter or blank filler must be installed in each PCI adapter cassette and the top cover for the system must be installed.
  • Page 66 3. Examine the PCI adapter slot opening carefully, and note the location of the dovetail rails and the cassette guide rails. A flashlight can be used to enable you to see the dovetail rails and the cassette guide rail slots, as shown in the following illustration. 1 Cassette Left Dovetail Rail 4 Cassette Bottom Guide Rail 2 Cassette Right Dovetail Rail...
  • Page 67 9. Visually check to ensure that the cassette is parallel with the cassettes to the left or right. If the cassette is not parallel with the neighboring cassettes, the cassette dovetail rails might not be correctly engaged. If the cassette is not correctly aligned, you might need to pull it out so you can see the ends of the dovetail rails.
  • Page 68 Replacing a Non-Hot-Pluggable PCI Adapter: Replace the adapter using the following procedure: Note: Because the adapter you are installing is not hot-pluggable, shut down the system and remove power before performing this procedure. 1. Depress the handle release lever of the PCI adapter cassette to release the latch, then lower the handle completely.
  • Page 69 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation.
  • Page 70 19. Carefully pull the PCI adapter cassette straight out from the rear of the subsystem. Take care not to pull EMC gaskets from neighboring cassettes. 1 I/O Subsystem 2 PCI Adapter Cassette 20. Install the replacement adapter in the PCI adapter cassette, see “PCI Adapter or Blank Filler Removal from a Cassette Assembly”...
  • Page 71 For more information on taking the PCI adapter online, see the AIX operating system documentation. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/en_US/infocenter/base. Select AIX documentation.
  • Page 72 4. Log in as root user. If the system is a partitioned system, log in as root user on the partition that has the adapter assigned to it. 5. At the command line, type smitty. 6. Select Devices. 7. Select PCI Hot Plug Manager. 8.
  • Page 73 Installing a Hot-Pluggable PCI Adapter: Attention: The Linux operating system does not support these hot-plug procedures. Also, Linux does not support hot-plugging any hot-pluggable PCI adapters. Systems with Linux installed on one or more partitions must be shut down and powered off before replacing any PCI adapter assigned to a Linux partition.
  • Page 74 e. Slide the cassette partially into the guide. f. Ensure that the dovetail on the top track aligns with its mating component(s) on both sides. 1 I/O Subsystem 2 PCI Adapter Cassette g. When the cassette is fully inserted, prepare to activate the handle, lower the locking bar. Lift the handle all the way up until you hear a click.
  • Page 75 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 76 List PCI Hot-Plug Slots Provides a descriptive list of all slots that support PCI hot-plug capability. If the listing for a slot indicates it holds an “Unknown” device, select the Install/Configure Devices Added after IPL to configure the adapter in that slot. Add a PCI Hot-Plug Adapter Allows the user to add a new PCI hot-plug-capable adapter to the slot with the system turned on.
  • Page 77 Install/Configure Devices Added After IPL The system attempts to configure any new devices and tries to find and install any required software from a user-selected source. The add, remove, and replace functions return information to the user indicating whether the operation was successful.
  • Page 78 PCI Adapter or Blank Filler Removal from a Cassette Assembly: Use this procedure when you are preparing to install or replace an adapter or an adapter blank filler in the system unit or an I/O drawer. Note: An adapter or an adapter blank filler must be installed into the PCI adapter cassette assembly before it is reinstalled in a system unit or an I/O drawer.
  • Page 79 2. Using two fingers, remove the bushing-lock pin from the bushing. The pin can be removed by pulling it out of the bushing with your fingernails. 1 Bushing 2 Bushing-Lock Pin 1 Bushing-Lock Pin Chapter 3. Removal and Replacement Procedures...
  • Page 80 3. Remove the bushing. The bushing can be removed by pulling it out of the PCI adapter cassette assembly with your fingernails. 1 Bushing 4. Turn over the PCI adapter cassette assembly so that the top is facing away from you. 1 Top of Adapter 2 Handle Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 81 5. Remove the bezel, as follows: a. Locate the plastic latch fingers in the top part of the cassette. 1 Top of Cassette 2 Bezel 3 Plastic Latch Fingers b. Using one hand, pinch the plastic latch fingers, and with your other hand, carefully lift the top part of the bezel extension out until the tabs clear the slots in the PCI adapter cassette assembly.
  • Page 82 c. While holding the bezel extension out, push the plastic cover latch out of the bezel hook, as shown in the following illustration. This action allows the bezel to be removed. 1 Bezel Extension 2 Plastic Cover Latch in Bezel Hook d.
  • Page 83 e. While holding the bezel extension out, carefully slide the bezel off. You might have to work from both sides to loosen the bezel assembly from the cassette assembly. When the bezel is free, slide it completely off the cassette assembly, and set it aside. 1 Bezel Extension 2 Bezel 1 Bezel...
  • Page 84 6. Turn over the cassette so that the cover is facing up, as shown in the following illustration. Remove the cover from the cassette as follows: a. Slide the cover until it releases from the cassette assembly. Attention: The cover might be tight and difficult to slide. If you grasp the left end (handle end) of the cassette and the right end of the cover, you can use enough force to pull the cover off the PCI adapter cassette assembly.
  • Page 85 7. Remove the metal EMC shield from the top of the tailstock. 1 Metal EMC Shield 8. Remove the blank filler or adapter that is installed in the cassette linkage assembly. Note: If there is a blank filler in the cassette linkage assembly, as shipped from the manufacturer, there are two adapter arms.
  • Page 86 Short Adapter or Blank Filler Removal: To remove a short adapter or blank filler, do the following: Slide the long and short adapter arms away from the adapter or blank filler by doing the following: Each adapter arm has a release tab that allows the arm to be moved away from the adapter or blank filler in the cassette assembly.
  • Page 87 2. Remove the adapter or blank filler from the cassette linkage assembly by rotating the bottom of the tailstock out, as shown in the following illustration. Store the adapter or blank filler in a safe place. 1 Cassette Linkage 3 Handle Assembly 2 Bottom of Tailstock 3.
  • Page 88 Long Adapter Removal: To remove a long adapter, do the following: Each adapter arm has a release tab that allows the arm to be moved away from the adapter in the cassette assembly. Use your fingernail to lift the tab, to allow the arm to be moved away from the adapter.
  • Page 89 Chapter 3. Removal and Replacement Procedures...
  • Page 90 5700 IBM Gigabit Ethernet-SX PCI-X Adapter 53P5450 5701 IBM 10/100/1000 Base-TX Ethernet PCI-X Adapter 53P5450 5706 IBM 2-Port 10/100/1000 Base-TX Ethernet PCI-X Adapter 53P5450 5707 IBM 2-Port Gigabit Ethernet-SX PCI-X Adapter 53P5450 6203 PCI Dual Channel Ultra3 SCSI Adapter 44P2661...
  • Page 91 2. Use the following procedure to determine if you are installing a long adapter or a short adapter. If you know the length of your adapter, skip the following steps and proceed to step 3 on page 77. a. Remove the adapter from its protective packaging and, if present, remove the plastic extension handle from the end of the adapter.
  • Page 92 c. The cassette linkage is marked to show long or short adapters similar to the adapter shown in the following figure. Check the right end of the adapter to determine if it is long enough to fall into the long area of the cassette linkage. Ensure that the corner on the left end of the adapter is still aligned into the top adapter-retaining clip and determine the length of the adapter.
  • Page 93 3. Remove the adapter or blank filler and ensure that the handle is in the up position. If you need to move the handle, ensure that the locking bar is pulled into the unlocked position, and then rotate the adapter handle until the handle is in the up position (the cassette linkage will extend down beyond the cassette top).
  • Page 94 1 Cassette Linkage 3 Retaining Clip Assembly 2 Bottom of Tailstock 4 Handle Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 95 b. Rotate the adapter so that the adapter engages the slot in the bottom adapter-retaining clip and the top corner of the adapter is seated into the adjustable top adapter-retaining clip. Note: If the adapter is not a full-height adapter, you must slide the adjustable top adapter-retaining clip downward until the lower edge of the adapter is seated into the slot on the bottom adapter-retaining clip.
  • Page 96 c. Slide the short-adapter retaining arm toward the adapter or blank filler on the cassette linkage rail. 1) If the short-adapter retaining arm has been removed from the cassette linkage rail, install the short-adapter retaining arm and then slide the arm until it contacts the adapter or blank filler as shown in the following figure.
  • Page 97 e. Use the lower short adapter-retaining clip to engage and hold the bottom of the adapter. Note: It might be necessary to apply pressure to engage and hold the bottom of the adapter. 1 Lower Short Adapter Arm Clip f. To hold the top of the adapter, slide down the adjustable top adapter-retaining clip on the retaining arm.
  • Page 98 g. Press the lock on the handle, and rotate the adapter handle until it is in the down position (adapter or blank filler moves up into the cassette assembly). 1 Handle Release Lever 2 Lock Ensure the right end of the cassette linkage rail moves up into the cassette linkage assembly as shown in the following figure: 1 Right End of Cassette Linkage h.
  • Page 99 1 Top of Cassette 2 Handle Chapter 3. Removal and Replacement Procedures...
  • Page 100 i. Install the cover on the cassette assembly: 1) Place the cassette cover on the cassette assembly as shown below. Slide the cover toward the handle until the hole in the cover aligns with the hole in the cassette assembly. 1 Handle 2 Holes Aligned Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 101 Install the bezel assembly using the following procedure. 1) Carefully slide the bezel onto the cassette assembly. 1 Bezel Align and insert the cover arm latch in the hooked notch in the bezel. Chapter 3. Removal and Replacement Procedures...
  • Page 102 3) Align the top of the bezel assembly into the grooves on the top of the cassette assembly. Push the bezel onto the cassette linkage until the tab on the top of the bezel is seated in the recess of the cassette assembly. 1 Recess 3 Tab 2 Groove...
  • Page 103 k. Check for the following: 1) Ensure that the extension arm engages the pins on the cassette. You should be able to see the three pins in the holes in the arm. The bezel tab should be seated as shown in the following figure.
  • Page 104 3) Turn the cassette assembly over so the cover is up. Check the cover latch to ensure it is holding the bezel to the cover as shown. 1 Cover Latch l. Ensure the holes are aligned, and insert the bushing as shown. 1 Bushing Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 105 m. Insert the bushing lock pin into the hole in the bushing and push it in until it seats. 1 Bushing Lock Pin n. Depress the handle release lever to ensure the locking bar on the handle is pulled into the unlocked position.
  • Page 106 o. To install the metal EMC shield on the adapter bracket, do the following: 1) Ensure that the shield slides up inside the top of the cassette. 1 Metal EMC Shield Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 107 2) The metal shield has clips that slide over the top of the tailstock. Ensure that these clips are holding the EMC shield to the tailstock. 1 Top of Tailstock p. Depress the handle release lever on the handle and rotate the adapter handle until the handle is in the down position (adapter or blank filler moves up into the cassette assembly).
  • Page 108 q. Using the system documentation, determine if the adapter you are installing is hot-swappable. If the adapter is hot-swappable, move the slider on the color indicator to allow the orange to be visible. If the adapter is not hot-swappable, the blue color is visible. 1 Orange for Hot-Swappable 2 Blue for Not Hot-Swappable r.
  • Page 109 1 Top Adapter-Retaining Clip 3 Adapter 2 Cassette Linkage Assembly 4 Bottom of Tailstock 5 Handle Chapter 3. Removal and Replacement Procedures...
  • Page 110 b. Rotate the adapter so that the adapter engages the slot in the bottom retaining clip and the top corner of the adapter is seated into the top adjustable adapter-retaining clip. Note: If the adapter is not a full-height adapter, slide the top adjustable adapter-retaining clip downward until the lower edge of the adapter is seated into the slot on the bottom retaining clip.
  • Page 111 c. Install the long adapter-retaining arm onto the cassette linkage rail, as shown in the following figure, and slide the arm toward the adapter. 1 Cassette Linkage Assembly 3 Top Adapter Retaining Clip 2 Adapter Retaining Arm Chapter 3. Removal and Replacement Procedures...
  • Page 112 d. Ensure that the top adjustable adapter-retaining clip catches the corner of the adapter as shown in the following figures. 1 Long Arm Adjustable Retaining Clip e. Ensure that the bottom edge of the adapter is held by the groove in the lower part of the adapter-retaining arm.
  • Page 113 f. To hold the top of the adapter, slide down the top adjustable adapter-retaining clip on the retaining arm. 1 Long Adapter Retaining Arm g. Depress the handle release lever on the handle. Rotate the adapter handle until it is in the down position (adapter or blank filler moves up into the cassette assembly).
  • Page 114 Ensure the right end of the cassette linkage rail moves up into the cassette linkage assembly as shown below: 1 Right End of Cassette Linkage h. Position the adapter and cassette assembly with the handle on the left (in the down position) and the top facing away from you.
  • Page 115 i. Install the cover on the cassette assembly by placing the cassette cover on the cassette assembly as shown below. Slide the cover toward the handle until the hole in the cover aligns with the hole in the cassette assembly. 1 Top of Cassette 2 Handle Chapter 3.
  • Page 116 Install the bezel assembly using the following procedure: 1) Carefully slide the bezel onto the cassette assembly. 1 Bezel Align and insert the cover arm latch in the hooked notch in the bezel. Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 117 3) Align the top of the bezel assembly into the grooves on the top of the cassette assembly and then push the bezel onto the cassette linkage until the tab on the top of the bezel is seated in the recess of the cassette assembly. 1 Recess 3 Tab 2 Groove...
  • Page 118 k. Check for the following: Ensure that the extension arm engages the three pins on the cassette. You should be able to see the pins in the holes in the arm. The bezel tab should be seated as shown in the following figure.
  • Page 119 3) Turn the cassette assembly over so the cover is up and check the cover latch to ensure it is holding the bezel to the cover as shown. 1 Cover Latch l. Position the adapter with the cover side up. Ensure the holes are aligned and insert the bushing as shown.
  • Page 120 m. Insert the bushing lock pin into the hole in the bushing. Push on the pin until it seats. 1 Bushing Lock Pin n. Depress the handle release lever to ensure the locking bar on the handle is pulled into the unlocked position.
  • Page 121 o. To install the metal EMC shield on the adapter bracket, do the following: 1) Ensure that the shield slides up inside the top of the cassette. 1 Metal EMC Shield Chapter 3. Removal and Replacement Procedures...
  • Page 122 2) The metal shield has clips that slide over the top of the tailstock. Ensure that these clips are holding the EMC shield to the tailstock. 1 Top of Tailstock p. Press the lock on the handle and rotate the adapter handle until the handle is in the down position (adapter or blank filler moves up into the cassette assembly).
  • Page 123 1 Orange for Hot-Swappable 2 Blue for Not Hot-Swappable r. The adapter is ready to be installed into a system or an I/O drawer. Refer to your system documentation for more information. Chapter 3. Removal and Replacement Procedures...

  • Page 124: D10 Fan

    D10 Fan Before performing the following procedure, read “Safety Considerations” on page 41. Hot-Swap Fan Assembly Removal To remove a hot-swap fan, do the following: 1. Locate the cooling fan assembly on the front of the I/O subsystem. 2. Unscrew the thumbscrew that holds the fan into the I/O subsystem. 3.

  • Page 125: D10 Rio Cable

    D10 RIO Cable Removal 1. Turn off the power to the system. 2. Release the RIO cable retainers. 3. Disconnect the RIO cable. Replacement Replace in reverse order. D10 RIO Bus Adapter Assembly Removal Before performing the following procedure, read the “Safety Considerations” on page 41. 1.

  • Page 126: D10 I/O Backplane Assembly

    D10 I/O Backplane Assembly Before performing the following procedure, read the “Safety Considerations” on page 41. Note: The I/O backplane and the SPCN riser card are replaced as a pair. Removal 1. Turn off the system power. 2. Put the I/O subsystem into the service position as described in “D10 Service Position” on page 43. 3.

  • Page 127: D10 Power Supply

    D10 Power Supply Before performing the following procedure, read the “Safety Considerations” on page 41. Removal Attention: Do not remove two power supplies at the same time if performing hot-plug procedures. Power supplies are considered as hot-pluggable FRUs only if you remove one power supply at a time. The power supplies can be removed from the front of the I/O subsystem.

  • Page 128: Removal And Replacement Procedures For The Model D20 I/O Subsystem

    Removal and Replacement Procedures for the Model D20 I/O Subsystem Notes: 1. All of the parts in the 7311 Model D20 I/O Subsystem can be replaced with the subsystem installed in a rack. The power supplies, blowers, disk drives, and PCI adapters are hot-pluggable. Under normal conditions, during the swapping of these FRUs, there is no need to shut down or unplug the system.

  • Page 129: D20 Service Position

    D20 Service Position Attention: When placing your Model D20 subsystem into the service position, all stability plates must be firmly in position to prevent the rack from toppling. Ensure that only one system drawer is in the service position at a time. Before doing any service actions inside your Model D20 subsystem, put the Model D20 subsystem into the service position.

  • Page 130: D20 Operating Position

    1 Model D20 Subsystem 4 Stabilizing Bar 2 19-Inch Rack 5 Front Rack Door 3 Extension Rail Safety Release Latch 6 System Drawer Release Latch After completing the service actions, return the Model D20 subsystem to the operating position. D20 Operating Position To return your Model D20 subsystem to the operating position, do the following: 1.

  • Page 131: D20 Service Access Cover

    D20 Service Access Cover Before performing the following procedure, read the “Safety Considerations” on page 41. Opening the Service Access Cover To open the service access cover, do the following: 1. Open the front rack door and place the Model D20 subsystem into the service position as described in “D20 Service Position”...

  • Page 132: D20 Front Bezel

    D20 Front Bezel Before performing the following procedure, read the “Safety Considerations” on page 41. Front Bezel Removal To remove the front bezel, do the following: 1. Open the front rack door. If necessary, place the Model D20 subsystem into the service position as described in “D20 Service Position”...

  • Page 133: D20 Operator Panel

    D20 Operator Panel Before performing the following procedure, read “Safety Considerations” on page 41. 1 Power LED (Green) 2 Attention LED (Amber) 3 Operator Panel 4 Snap Buttons Operator Panel Removal To remove the operator panel from the subsystem, do the following: 1.

  • Page 134: Operator Panel Replacement

    1 Rack Front Door 4 Snap Buttons 2 Model D20 5 Front Bezel 3 Operator Panel Operator Panel Replacement To replace the operator panel, do the following: 1. Connect the power/signal cable connector to the back of the operator panel. 2.

  • Page 135: D20 Blowers

    D20 Blowers Before performing the following procedure, read “Safety Considerations” on page 41. Each cooling blower assembly has a green LED and an amber LED. The green LED indicates when the cooling blower is receiving power. A blinking amber LED indicates when the cooling blower needs attention from a potential cooling problem.
  • Page 136 1 Green LED 4 Blower Connector 2 Amber LED 5 Hot-Plug Blower Assembly 3 Snap Button 6 Docking Connector Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 137 Hot-Swap Blower Replacement Note: If a blower assembly is being replaced for a redundant failure, after the service repair action is completed, ask the customer to check the crontab file for any power/cooling warning messages. When a power or cooling error is encountered, AIX adds an entry to the crontab file to ″wall″ a warning message every 12 hours, to alert or remind the customer of the problem.

  • Page 138: D20 Cooling Blower Cable

    D20 Cooling Blower Cable This procedure must be performed with the power turned off. Cooling Blower Cable Removal To remove the cooling blower cable, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping and Starting the System” on page 42. 3.
  • Page 139 1 Cooling Blowers 6 Connector Retaining Ears 2 Cable Ties 7 Blower Docking Connector 3 Power Supply 8 Model D20 4 Tab Retaining Clip 9 Blower Connector Support 5 Connector Release Tab Cooling Blower Cable Replacement Replace in reverse order. Chapter 3.

  • Page 140: D20 Rio Bus Adapter Assembly

    D20 RIO Bus Adapter Assembly Before performing this procedure, read “Safety Considerations” on page 41. In the following RIO bus adapter removal and replacement procedures, the RIO bus adapter assembly is referred to as the RIO adapter. RIO Bus Adapter Removal To remove the RIO adapter from the subsystem, do the following: 1.
  • Page 141 1 RIO Bus Adapter Release Handle 4 Service Access Cover 2 RIO Bus Adapter Release Latch 5 Model D20 Subsystem 3 RIO Bus Adapter Chapter 3. Removal and Replacement Procedures...
  • Page 142 RIO Bus Adapter Replacement To replace the RIO bus adapter, do the following: 1. Grasp the two RIO adapter release handles. 2. Pivot both handles upward to 90 degrees, ensuring that the handles are perpendicular to the RIO adapter. The handle cams have now been placed into the correct position to assist you when seating the RIO adapter into its docking connector.

  • Page 143: D20 Pci Adapters

    For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 144 To access the hot-plug menus, do the following: 1. Log in as root user. 2. At the command line, type smitty. 3. Select Devices. 4. Select PCI Hot Plug Manager and press Enter. 5. The PCI Hot-Plug Manager menu displays. Return to the procedure that directed you here. The following section describes the menu options.
  • Page 145 Unconfigure a Device Allows the user to put an existing PCI adapter into the Defined state if the device is no longer in use. This step must be completed successfully before starting any removal or replacement operation. If this step fails, the customer must take action to release the device. Configure a Defined Device Allows a new PCI adapter to be configured into the system if software support is already available for the adapter.
  • Page 146 Non-Hot-Pluggable PCI Adapter Removal To remove a PCI adapter, do the following: 1. Open the front and rear rack doors, and place the subsystem into the service position as described in “D20 Service Position” on page 113. 2. Shut down the system as described in “Stopping and Starting the System” on page 42. 3.
  • Page 147 8. Rotate the adapter retainer clip counterclockwise, as shown in the following illustration. 9. Lift the adapter retaining seat that is resting on the adapter retention bracket. 10. Carefully grasp the PCI adapter by its top edge or upper corners, and remove it from the system. 11.
  • Page 148 Adding or Replacing a Non-Hot-Pluggable PCI Adapter To add or replace an adapter, do the following: 1. Open the front and rear rack doors, and place the system into the service position as described in “D20 Service Position” on page 113. 2.
  • Page 149 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 150 14. Select Replace/Remove a PCI Hot-Plug Adapter and press Enter. The Replace/Remove a PCI Hot-Plug Adapter menu displays. Note: If the PCI Hot-Plug Adapter menu indicates that the slot for the just replaced adapter is reading empty, do the following: a.
  • Page 151 19. Turn the retainer clip and lift the adapter retaining seat off the adapter. 1 Model D20 2 Service Access Cover 3 Retainer Clip 4 Retainer Seat 5 PCI Adapter 20. Carefully grasp the adapter by the edges and pull it straight out from the PCI riser card. 21.
  • Page 152 For additional information about taking an adapter offline or removing it from the system configuration, see the AIX System Management Guide: Operating System and Devices. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 153 8. Select Unconfigure a Device and press Enter. Note: If the adapter or device has a problem that prevents it from being replaced by hot-plug, it must be replaced by shutting down the system. Go to “Adding or Replacing a Non-Hot-Pluggable PCI Adapter”...
  • Page 154 17. Move the cursor to select the adapter that you are removing, and press Enter. 18. Press the Tab key until the entry field displays the replace operation, and then press Enter. Follow the instructions that display on the screen until you are instructed to remove the adapter. 19.
  • Page 155 If you have added, removed, or replaced any adapters, run the diag -a command. If the system responds with a menu or prompt, follow the instructions to complete the device configuration. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 156 9. Refer to “PCI Hot-Plug Manager Access” on page 127, and follow the steps in the access procedure to select PCI Hot Plug Manager. Then return here to continue. 10. From the PCI Hot-Plug Manager menu, select Add a PCI Hot-Plug Adapter and press Enter. The Add a Hot-Plug Adapter window displays.

  • Page 157: D20 Hot-Plug Disk Drives

    2. Before a disk can be removed from a volume group, all data must be backed up and the data removed from the disk to be replaced. Use AIX Logical Volume Manager to perform this task. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 158 13. See the AIX System Management Guide: Operating System and Devices to finish the drive configuration. Documentation for the AIX operating system is available from the IBM Eserver pSeries Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Select AIX documentation. The AIX Documentation CD contains the base set of publications for the operating system, including system-management and end-user documentation.
  • Page 159 Hot-Plug Disk Drive Removal Attention: The Linux operating system does not support these hot-plug procedures. Also, Linux does not support hot-plugging any hot-pluggable PCI adapters. Systems with Linux installed on one or more partitions must be shut down and powered off before replacing any PCI adapter assigned to a Linux partition.
  • Page 160 1 Rack Front Door 3 Disk Drive Release Handle 2 Model D20 4 Front Bezel Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 161 Hot-Plug Disk Drive Replacement Attention: The Linux operating system does not support these hot-plug procedures. Also, Linux does not support hot-plugging any hot-pluggable PCI adapters. Systems with Linux installed on one or more partitions must be shut down and powered off before replacing any PCI adapter assigned to a Linux partition.

  • Page 162: D20 Disk Drive Cage

    D20 Disk Drive Cage Before performing the following procedure, read “Safety Considerations” on page 41. Disk Drive Cage Removal To remove the disk drive cage, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping and Starting the System” on page 42. 3.
  • Page 163 1 Model D20 5 Retaining Screws (Quantity 8) 2 Disk Drive Cage 6 Light Pipes 3 Disk Drives 7 Light Pipe Support Bracket 4 Front Bezel Disk Drive Cage Replacement To replace the disk drive cage, go the following: 1. Insert the disk drive cage assembly into the subsystem. 2.

  • Page 164: D20 Disk Drive Backplane

    D20 Disk Drive Backplane Before performing the following procedure, read “Safety Considerations” on page 41. Disk Drive Backplane Removal To remove the disk drive backplane, do the following: 1. Remove all hot-plug disk drives as described in “Hot-Plug Disk Drive Removal” on page 143. 2.
  • Page 165 Disk Drive Backplane Replacement To replace the disk drive backplane, do the following: 1. Reconnect the power/signal cable to the connector located on the top edge of the disk drive backplane. 2. Grasp a bottom edge of one of the connectors located on the disk drive backplane, and insert the backplane into the disk drive bay.

  • Page 166: D20 Power Supplies

    D20 Power Supplies DANGER Do not attempt to open the covers of the power supply. Power supplies are not serviceable and are to be replaced as a unit. The Model D20 subsystem has power supplies that have hot-swap capabilities. To use this feature, you must have two power supplies in place.

  • Page 167: Power Supply Replacement

    7. Carefully remove the power supply from the subsystem. 1 Power Supplies 4 Green DC Good LED 2 Green Power LED 5 Power Supply Filler 3 Amber Fault/Identify LED 6 Model D20 Subsystem Note: During normal operation, each power-supply bay must have either a power supply or filler panel installed for proper cooling.

  • Page 168: D20 Power Supply Bulkhead

    D20 Power Supply Bulkhead Before performing the following procedure, read the “Safety Considerations” on page 41. Power Supply Bulkhead Removal To remove the power supply bulkhead, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping and Starting the System” on page 42. 3.
  • Page 169 1 Power Supply Filler 5 PCI-X Adapters 2 Power Supply Bulkhead 6 Model D20 3 PCI Dividers 7 Power Supplies 4 RIO Bus Adapter Chapter 3. Removal and Replacement Procedures...
  • Page 170 Power Supply Bulkhead Replacement To replace the power supply bulkhead, do the following: 1. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 42. 2.

  • Page 171: D20 I/O Backplane Assembly

    D20 I/O Backplane Assembly Before performing the following procedure, read the “Safety Considerations” on page 41. I/O Backplane Removal To remove the I/O backplane from the subsystem, do the following: 1. Open the rack front door. 2. Shut down the system as described in “Stopping and Starting the System” on page 42. 3.
  • Page 172 15. Remove the plastic membrane from the top of the I/O backplane by first removing the five retaining screws that secure the plastic membrane to the I/O backplane. Note: When removing the plastic membrane, slide the membrane under the light pipes that identify the green and amber power LEDs.
  • Page 173 1 I/O Backplane 2 VPD Module Attention: Note the location of Pin 1 before removing. 27. Note the location of pin 1 on the VPD module. 28. Gently remove the VPD module and put it in a safe place. Note: You will be installing the old VPD module onto the new I/O backplane. Chapter 3.
  • Page 174 1 PCI Adapter Dividers (maximum 6 Plastic Membrane quantity 7) 2 RIO Bus Adapter 7 Model D20 3 PCI-X Adapters (maximum quantity 7) 8 SCSI Cable Bracket 4 Power Supplies 9 PCI Adapter-Headstock Bracket 5 I/O Backplane 10 Power-Supply Bulkhead 5a VPD Module Eserver pSeries 7311 Model D10 and Model D20 Service Guide...
  • Page 175 I/O Backplane Replacement To replace the I/O backplane, do the following: 1. Before handling any card, board, or memory DIMM, be sure to use your electrostatic discharge strap to minimize static-electric discharge. Refer to “Handling Static-Sensitive Devices” on page 42. 2.
  • Page 176 19. Replace all of the previously removed PCI adapters as described in “Adding or Replacing a Non-Hot-Pluggable PCI Adapter” on page 132. Note: Alternately reinstall the PCI dividers, when reinstalling the PCI adapters. 20. Reconnect all PCI adapter cables to their respective adapters. 21.

  • Page 177: Chapter 4. Parts Information

    Chapter 4. Parts Information This chapter contains parts information for the 7311 Model D10 and Model D20 I/O drawers. 7311 Model D10 I/O Subsystem This section lists part numbers for the 7311 Model D10 I/O Subsystem. This I/O subsystem is used in conjunction with a system unit.
  • Page 178 Index Part Number Units Per Assy Description 00P2752 Bracket, Bulkhead 09P4656 Tray, cable 09P5417 Cable, fan 09P3128 Guide, mounting 1624749 Screw, guide mounting ******* See index number 9 1621829 Screw, tray mounting 1624743 Screw, backplane mounting 09P5921 I/O backplane assembly (includes SPCN connector card ) 1621829 Screw, tailstock cover mounting...

  • Page 179: D10 I/O Subsystem Parts (Continued)

    D10 I/O Subsystem Parts (continued) Chapter 4. Parts Information...
  • Page 180 Index Part Number Units Per Assy Description 00P2753 Cover, access 09P4778 Front bezel, black 09P5159 Front bezel, white 1624743 Screw, guide mounting 00P2750 Guide, adapter cassette top 44P0239 Empty PCI adapter cassette kit 00P3842 PCI adapter cassette blank filler, long 00P3843 PCI adapter cassette blank filler, short 53P5450...

  • Page 181: D10 Spcn, Rio, And Rack Beacon Cables (These Parts Are Not Shown.)

    D10 SPCN, RIO, and Rack Beacon Cables (These parts are not shown.) Index Part Number Units Per Assy Description 53P2231 Up to 12 Rack beacon junction box, 7-port mini connector (4693) 53P2237 Up to 12 Rack beacon connector cable, subsystem to junction box, 4-pin std to 4-pin mini connector, 3 meter (4691) 07H6655 As needed...

  • Page 182: Model D20 I/O Subsystem

    Model D20 I/O Subsystem This section lists part numbers for the 7311 Model D20 I/O Subsystem. This I/O subsystem is used in conjunction with a system unit. Depending on your configuration, the quantities of parts listed may increase by the actual number of I/O subsystems connected to the system unit. D20 I/O Backplane and Cabling Index Part Number...

  • Page 183: D20 Pci Slots

    D20 PCI Slots Index Part Number Units Per Assy Description See Note 7 (maximum PCI adapter quantity) 53P0248 Power supply bulkhead 44H7366 Screw, power bulkhead mounting 44H7366 Screw, PCI plate mounting 53P0249 PCI adapter headstock bracket 53P2728 PCI dividers 53P2729 PCI dividers 03K8992 PCI adapter, empty slot filler...

  • Page 184: D20 Power, Rio Adapter, Cabling

    D20 Power, RIO Adapter, Cabling Index Part Number Units Per Assy Description 53P4832 2 (maximum Power supply quantity) 53P3800 RIO bus adapter 97P2670 RIO-2 bus adapter 53P2690 Cable bracket, SCSI 44H7366 Screw, SCSI cable 53P0639 RIO-2 cable bracket 44H7366 Screw, RIO-2 cable bracket 53P0417 Configuration SCSI bus cable...

  • Page 185: D20 Operator Panel

    D20 Operator Panel Index Part Number Units Per Assy Description 97P3138 DASD SCSI Backplane 53P0321 Screw, disk-drive-backplane mounting 53P0330 Operator panel 53P0275 Processor cover 44H7366 Screw, cover-mounting Chapter 4. Parts Information...

  • Page 186: D20 Fans And Disk Drives

    D20 Fans and Disk Drives Index Part Number Units Per Assy Description 53P0262 Blower Model D20 53P0250 Disk-drive cage 12 pack (disk drive back planes included) Note: If the light pipes attached to the cage get broken, the entire cage needs to be replaced. 53P0319 Screw, DASD-cage mounting Disk Drives...

  • Page 187: D20 Covers And Brackets

    D20 Covers and Brackets Index Part Number Units Per Assy Description 53P1457 Front bezel 44H7366 Screw, latch bracket 53P2572 Latch bracket assembly left 53P0295 Cable arm bracket 44H7366 Screw, cable arm bracket 53P2573 Latch bracket assembly right D20 RIO, SPCN, and Rack Beacon Cables Index Part Number Units Per Assy...

  • Page 188: Power Cables

    Power Cables Index Part Number Country or Region 1838574 Bahamas, Barbados, Bolivia, Brazil, Canada, Costa Rica, Dominican Republic, El Salvador, Ecuador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan, Netherlands Antilles, Panama, Peru, Philippines, Taiwan, Thailand, Trinidad, Tobago, U.S.A. (except Chicago), Venezuela 86G7648 Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman Islands, Colombia, Costa Rica, Dominican Republic, Ecuador, El Salvador, Guatemala, Guyana, Haiti, Honduras,...

  • Page 189: Chapter 5. Fault And Attention Leds

    Chapter 5. Fault and Attention LEDs This chapter contains information about fault and attention LEDs, which assist in identifying failing components in your system. Component LEDs Individual LEDs are located on or near the failing components. The LEDs are located either on the component itself or on the carrier of the component (for example, PCI adapters and disk drives).
  • Page 190 Unit Location Viewable LED Color OFF Blink (FRU) Function Location Power and Packaging LEDs Rack Amber Normal Fault Identify External Rack Summary Top of Rack Indicator AC Input External Front Green No Input AC Good Fault External Front Amber Normal Fault Identify Attention...
  • Page 191 Unit Location Viewable LED Color OFF Blink (FRU) Function Location Power and Packaging LEDs Disk Drive No LED Backplane Port LED Indicators Top of Each RIOPorts Identify External External Back Amber Normal Identify Connector Chapter 5. Fault and Attention LEDs...

  • Page 192: Resetting The Leds

    Resetting the LEDs After the repair action is completed, do the following: 1. Log in as root user. 2. At the command line, type diag. 3. Select Task Selection. 4. Select Log Repair Action. 5. Select the device that was repaired. 6.

  • Page 193: Appendix A. Environmental Notices

    Before this unit is disposed of, these materials must be removed and recycled or discarded according to applicable regulations. IBM offers product-return programs in several countries. For country specific instructions refer to the following web site: http://www.ibm.com/ibm/environment/products/prp.phtml This product may contain a sealed lead acid, nickel cadmium, nickel metal hydride, lithium, or lithium ion battery.
  • Page 194 Dette produkt kan indeholde et f orseglet batteri, der indeholder b ly, nikkel-kadmium, nikk el-metal-hydrid, litium eller litium-ion. Der er flere oplysninger om batter iet i bruger- eller servicevejledningen. Batteriet må ikke kasseres sammen med det almindelige aff ald. Batteriet skal kasseres i henhold til de lokale bestemmelser . Spørg eventuelt kommunens teknisk e forvaltning (Miljø...
  • Page 195 Questo prodotto potrebbe contenere una batteria al piombo, al nichel-cadmio, all ’idruro di nichel, al litio o agli ioni di litio. Consultare il manuale utente o il manuale di assistenza per informazioni specifiche sulla batteria. La batteria deve essere appropriatamente riciclata o smaltita. Il servizio per il riciclaggio potrebbero non essere disponibile nella vostra zona.
  • Page 196 Produkten kan innehålla ett förseglat batteri av någon av typerna blyackumulator , nickel-kadmium, nickel-metallhydrid, litium eller litiumjon. Detaljerad batteriinformation finns I användar - eller servicehandboken. Batteriet måste lämnas till återvinning eller kastas på ett miljösäkert sätt. Det kanske inte finns några återvinningsmöjligheter där du bor . När det gäller omhändertagande av batterier ber vi att få...

  • Page 197: Environmental Design

    In the United States, IBM has established a collection process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM Equipment. For information on proper disposal of these batteries, please contact IBM at 1-800-426-4333.

  • Page 198: Acoustical Noise Emissions

    Acoustical Noise Emissions The equivalent continuous A-weighted sound pressure level at workstations (emission sound pressure level at the 1-meter bystander positions) does not exceed 70 dB(A). Der Geräuschpegel der Einheit ist kleiner oder gleich 70 db(A). pSeries 7311 Model D10 Declared Acoustical Noise Emissions Acoustical Characteristic Product Configuration Declared A-Weighted Sound Power...

  • Page 199: Appendix B. Notices

    IBM encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. IBM offers a variety of programs and services to assist equipment owners in recycling their IT products. Information on product recycling offerings can be found on IBM’s Internet site...

  • Page 200: Battery Return Program

    In the United States, IBM has established a return process for reuse, recycling, or proper disposal of used IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM Equipment.

  • Page 201: Index

    Index D10 locations (continued) I/O backplane 12 accessing information xiii model D10 15 acoustical PHB 13 noise D10 replacement procedure list 42 emissions 182 D20 location code table 32 adapter, PCI removal and replacement, D10 45 D20 location codes 31 adapters, PCI D20 127 D20 locations 19 AIX documentation 53, 59, 127, 133, 136, 139, 141,...
  • Page 202 features, system 16 locations, D10 10 cooling 18 locations, D20 19 disk drives 17 operator panel 16 PCI-X slots 16 ports, input/output 18 MAP rules 40 ports, serial 18 power 18 slots, PCI-X 16 front bezel removal, D10 43 noise emissions front bezel replacement, D10 43 acoustical 182 front bezel replacement, D20 116...
  • Page 203 power supply bulkhead removal D20 152 removal procedures 41 power supply bulkhead replacement, D20 154 adapter, PCI D20 130 power supply locations 20 bezel, D20 116 power supply removal D20 150 blower cable, D20 122 power supply removal, D10 111 blowers, hot-swap, D20 119 power supply replacement, D10 111 caution and danger 41...
  • Page 204 Self-Test, Power-On 34 serial port configurations 18 service access cover removal, D10 44 service access cover removal, D20 115 service access cover replacement, D10 44 service access cover replacement, D20 115 service inspection guide 38 service position 113 service position, D10 43 SPCN cables 5 SPCN cables, parts 171 specifications 35...
  • Page 205 Thank you for your responses. May we contact you? h Yes h No When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you. Name...
  • Page 206 Readers’ Comments — We’d Like to Hear from You Cut or Fold Along Line SA38-0627-01 Fold and Tape Please do not staple Fold and Tape _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ NO POSTAGE NECESSARY IF MAILED IN THE...
  • Page 208 Printed in USA May 2003 SA38-0627-01...

This manual is also suitable for:

Pseries 7311 d20

Table of Contents