Table of Contents
Advertisement
1-c. Load the shell with the DataMart environment, by sourcing the
. /opt/datamart/dataMart.env
After you load the DataMart environment into the shell, the PVMHOME variable is set to the
Note:
DataMart home directory, /opt/datamart by default. These instructions assume that this variable has been set.
2.
Copy technology-specific files from the DataMart server to the DataChannel server.
Technology-specific files are used to associate a UBA technology pack with a specific instance of the UBA.
While it is possible to install DataMart and DataChannel on the same server, in a typical installation
Note:
these modules are installed on separate servers. If this is the case, use ftp to copy the technology-specific files.
Otherwise, if DataMart and DataChannel are on the same server, use the cp command to copy the files to the
appropriate DataChannel directory.
To copy technology-specific files to the DataChannel server, follow these steps:
2-a. Log in to the Tivoli Netcool/Proviso DataChannel server by entering the user name and password that
you specified when installing and configuring a DataChannel. The default user name and password are
and
pvuser
2-b. Change your working directory to the DATA_CHANNEL_HOME
directory by entering the following command, replacing
DataChannel home directory (
DATA_CHANNEL_HOME
$ cd
2-c. Using the
ftp
password (
pvuser
2-d. Using the
cd
$PVMHOME/APFiles/voip_cisco_ipt/datachannel/scripts/voip_cisco_ipt
directory.
2-e. Using the
get
files (if any) from the DataMart server to the DataChannel server.
2-f. (Tivoli Netcool/Proviso pre-v4.4.3 only) Copy the
file as follows:
• Using the
cd
$PVMHOME/APFiles/voip_cisco_ipt/datachannel/conf
• Using the
get
DataMart server to the DataChannel server.
2-g. Exit the
ftp
2-h. Verify that the technology-specific files are now located in the target directory as follows:
• (Tivoli Netcool/Proviso v4.4.3 and later) Verify that the Bulk Adaptor Design Files (
(if any), other files (if any) are now located in the
DATA_CHANNEL_HOME
• (Tivoli Netcool/Proviso pre-v4.4.3 only) Verify that the Bulk Adaptor Design Files (
(if any), other files (if any), and
the DATA_CHANNEL_HOME
3.
Activate data collection requests.
During installation of the technology pack, all predefined data collection requests are promoted to the
database and set to inactive (that is,
DataMart Request Editor). You need to activate these predefined data collection requests using the Request
Editor.
To set data collection requests to active, follow these steps:
IBM Tivoli Netcool/Proviso Cisco IP Telephony 2.4.0.0 Technology Pack
, respectively.
PV
/opt/datachannel
/scripts/voip_cisco_ipt
utility in text mode, log into the DataMart server using the appropriate user name and
and
, by default).
PV
subcommand, change your working directory to the
subcommand, copy the Bulk Adaptor Design Files (
subcommand, change your working directory to the
subcommand, copy the
voip_cisco_ipt_sample_dc.cfg
utility by entering the
subcommand.
bye
/scripts/voip_cisco_ipt
voip_cisco_ipt_sample_dc.cfg
/scripts/voip_cisco_ipt
displays in the
idle
Chapter 4: Configuring the technology pack
dataMart.env
/scripts/voip_cisco_ipt
DATA_CHANNEL_HOME
, by default):
), scripts (if any), and other
*.js
voip_cisco_ipt_sample_dc.cfg
directory.
directory.
template file are now located in
directory.
column of the Tivoli Netcool/Proviso
Active
file, as follows:
with the
template
template file from the
), scripts
*.js
), scripts
*.js
47
Advertisement
Table of Contents
