TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT SUPPLEMENTS PUBLISHED BY SONY.
Page 3
y l l . s l . s l . s l e i l . s l n i l & n i l i n i y t i - 3 -...
21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
FE-2 SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal => => => Remove the rear cover fixing screws indicated and withdraw the rear cover from the Beznet. 2-2. Chassis Removal and Refitting When refitting the chassis ensure that the main bracket is located in the beznet guide slots before sliding the chassis forwards.
2-3. A Board Removal [ Step 1 ] 2-4. A Board Removal [ Step 2 ] Clip. Screw. Remove the 3 screws securing the PWB to the main bracket. Release the 3 securing clips located at the side of the chassis 1 can be seen in the photo above and the other 2 are either and slide the PWB clear of the bracket.
2-6. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
SECTION 3 SET-UP ADJUSTMENTS • Carry out the adjustments in the following order : When complete readjustment is necessary or a new picture 3-1. Beam Landing. tube is installed, carry out the following adjustments. 3-2. Convergence. • Unless there are specific instructions to the contrary, carry 3-3.
If the V.STAT magnet is moved in the direction of the (a) 3-2. Convergence and (b) arrows, the Red, Green and Blue points move as indicated below. Preparation: • Before starting this adjustment, adjust the focus, horizontal size and vertical size. •...
Page 19
Geometry Adjustment. YCH Adjustment Preparation: YCH VR Before starting this adjustment, adjust the horizontal and Deflection Yoke vertical static convergence. Remove the deflection yoke spacer. Tilt the deflection yoke as indicated in the figure below and TLV Adjustment optimise the geometry. Tilting the DY Up and Down will balance the upper and lower pin adjustment.
Layout of each control 3-4. Screen (G2), White Balance [Adjustment in the service mode using the remote commander] G2 adjustment Input a dot signal from the pattern generator. Enter the ‘Service Mode’ by pressing ‘TEST’, ‘TEST’ and ‘38’ (TT-38) on the remote commander, to set up the G2 V.STAT service adjustment mode.
SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-947. How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander.
Page 22
Deflection System Adjustment Sub Colour Adjustment Enter into the ‘Geometry’ service menu. Receive a PAL colour bar signal. Select and adjust each item in order to obtain the optimum image. Connect an oscilloscope to Pin 5 of CN3003 [A Board]. Enter into the ‘Service’...
4-2. TEST MODE 1: Test Mode 1 is available by pressing the ‘TEST’ button once, OSD ‘T’ appears. The functions described below are available by selecting the indicated keys. The ‘T’ is released automatically after each command is executed. y t i s i l i n i i n i...
5-1. BLOCK DIAGRAMS (1) CN7007 IC0001 CN2201 MICRO, VIDEO PROCESSOR, R.G.B. OUT TO A BOARD CN5008 ROM, AUDIO, VIDEO SWITCH R AUDIO CN0001 TO SPEAKERS +3.3V CN7006 L AUDIO XTAL IN STBY TO A BOARD IC2201 CN5009 IC0002 XTAL OUT J2200 AUDIO AMP REMOTE CONTROL...
5-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM : SOLID FPRD : NON FLAMMABLE CARBON C Board FUSE : NON FLAMMABLE FUSIBLE : NON FLAMMABLE METAL OXIDE : NON FLAMMABLE CEMENT DF Board : NON FLAMMABLE WIREWOUND CVM Board A Board S1 Board : ADJUSTMENT RESISTOR...
Page 27
A Board Difference Table ~ A Board Waveforms ~ A Board IC Voltage Table 20us/div 20us/div 1.88 Vp-p (H) 1.84 Vp-p (H) 20us/div 20us/div 1.86 Vp-p (H) 6.0 Vp-p (H) 20us/div 20us/div 5.4 Vp-p (H) 16.8 Vp-p (H) 20us/div 5ms/div 1.83 Vp-p (V) 488 mVp-p (V) 5ms/div...
Page 28
~ A Board Semiconductor Location Table ~ NOTE: Portions of the circuit marked as shown are high ~ A Printed Wiring Board Conductor side ~ voltage areas. Use care to prevent electric shock during inspection or repair. - 28 -...
A BOARD COMMON Parts List : Parts common to all models in this manual ..........43 A BOARD VARIANT Parts List : Parts that belong only to the model specified Model (KV-29CL11B) : ....................50 (KV-29CL11E/KV-29CL11K) : ....................51 MISCELLANEOUS : ....................
Page 52
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.