Table of Contents
Advertisement
Available languages
Available languages
Once you are done with setting available options,
press the Right directional button to proceed. The TV
will start to search available broadcasts.
Satellite
If Satellite option is selected, Antenna Type screen
will be displayed next. If you have a Direct satellite
system, you can proceed to the next step quickly by
selecting the Next option here. Highlight More and
press OK to set the antenna type manually. Single,
Tone Burst, DiSEqC and Unicable options are
available. Highlight the antenna type that corresponds
to your satellite system and press OK or the Right
directional button to proceed to the next step.
Next screen will be Select Operator screen. You
can select only one operator from the list. Highlight
the desired operator and press OK or the Right
directional button to proceed. Some of the options in
the following steps may be preset and/or additional
steps may be added or some steps may be skipped
depending on the selected operator in this step. Check
the parameters in each step before proceeding and
adjust if necessary. You can highlight General and
press OK or Right directional button to proceed with
normal satellite installation.
Tivusat Installation
You can search and store Tivusat channels. Set
the tuner mode as Satellite. On the next screen
set the antenna type as mentioned above. Then
Select Operator screen will be displayed. Select
the operator accordingly. Press OK or the Right
directional button to proceed.
Note: If you want the channels to be sorted in the preset
order of Tivusat set the satellite as Hotbird at 13.0º East
(13.0E).
LNB List screen will be displayed next. You may be
able to set up different satellites depending on the
selected country, antenna type and operator in the
previous steps. Highlight the desired satellite option
and press OK or the Right directional button to set
the parameters. The Satellite Status of the first
satellite option will be set as On. In order to enable
channel scan on the satellite, this option should be
set as On first.
Following satellite parameters will be available. You
may not be able to change all settings depending on
the previous selections.
Satellite Status: Set the status option to On to
enable channel search on the selected satellite.
Highlight this option and press OK to change the
status.
Satellite Selection: Select the satellite on which you
want to perform a channel search.
Scan Mode: Set your scan mode preference. Full
and Network options will be available. If you are
going to perform a network scan, make sure that
you have adjusted the Frequency, Symbol Rate
(Ksym/s) and Polarisation parameters under the
Transponder option accurately.
Scan Type: You can perform a scan for free or
encrypted channels only. If the Free option is
selected encrypted channels will not be installed.
Select All to scan all channels.
Store Type: You can select to store TV channels
(referred to as 'Digital Channels' in the menu) or
radio channels only. Select All to store all channels.
Transponder: Adjust the Frequency, Symbol Rate
(Ksym/s) and Polarisation parameters for the
selected satellite if necessary.
LNB Configurations: Set the parameters for LNB.
For DiSEqC antenna type select the correct DiSEqC
port corresponding to your satellite system. Set other
parameters in accordance with your satellite system
if necessary.
Signal Quality: The signal quality status is displayed
as a percentage.
Signal Level: The signal level status is displayed
as a percentage.
Press the Back/Return button and select next satellite
you want to set. After you completed the configuration
changes, highlight Next on the LNB List screen and
press OK or Right directional button to proceed.
If Load Preset List option is selected in the previous
step next steps will be skipped and the preset channel
list installation will start. If the correct satellite has not
been selected for SatcoDX installation, a warning
dialogue will be displayed on the screen. The satellite/s
that can be selected will be listed. Press OK to close
the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select
Skip Scan to proceed without performing a scan
and complete the initial setup. Select Only digital
channels and press OK or the Right directional button
to start the search. While the search continues you can
press the Back/Return button, highlight Skip Scan
and press OK or Right directional button to stop the
search. The channels that have already been found
will be stored in the channel list.
When the initial setup is completed a message will be
displayed. Press OK to finish the setup.
You will be asked to give your consent to the
collection of your data. Read the text on the screen
for detailed information. Highlight Accept and press
OK to give your consent and proceed. To skip
without giving your consent, select Skip. You can
change this setting later using the Settings>Device
Preferences>Manufacturer Usage & Diagnostics
menu.
Home Screen will be displayed. You can press the Exit
button on the remote to switch to Live TV mode and
watch TV channels.
English - 11 -
Advertisement
Chapters
Table of Contents
