Table of Contents
Advertisement
Quick Links
Gamma instabus
Switching Actuator N 535D51, 8 x AC 230 V, 16/20 AX, C-load
Switching actuator N 535D51
For switching capacitive, inductive and resistive loads
Maintenance-free terminals for connecting and looping through solid, stranded and
fine-stranded conductors with conductor cross-sections from 0.5 to 2.5 mm²
Switching status display with operating capability for each output to test for correct
installation
Functions with configuration with ETS
Control functions:
Switching with status message, logic gate, central switching, timed switching, night
o
mode
Control value input for analogous values can be configured as an alternative to the
o
switching input
Integrated 8-bit scene control and assign of each output to up to 8 scenes
o
Override functions: Manual ON, permanent OFF, locks, central override, forced control
Diagnostic functions: Counting of switching cycles with threshold monitoring of switch
cycles, counting of operating hours with threshold monitoring of operating hours, load
detection with threshold monitoring of load check, status messages
Technical product information
Advertisement
Table of Contents
Related Manuals for Siemens N 535D51
Summary of Contents for Siemens N 535D51
- Page 1 Gamma instabus Technical product information Switching Actuator N 535D51, 8 x AC 230 V, 16/20 AX, C-load Switching actuator N 535D51 For switching capacitive, inductive and resistive loads Maintenance-free terminals for connecting and looping through solid, stranded and fine-stranded conductors with conductor cross-sections from 0.5 to 2.5 mm²...
-
Page 2: Type Overview
Switching actuator with Load Check monitoring Characteristics Switching actuator N 535D51 can switch eight mutually independent groups of electrical consumers via eight potential-free outputs. The switching actuator can switch resistive loads (e.g. electric heater, incandescent lamps), inductive loads (e.g. motor, low-voltage halogen lamps with upstream wound transformer) or capacitive loads (e.g. -
Page 3: Technical Design
Labeling of the switching contacts for channels E, F, G and H Switch position display with manual operation 3 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug... - Page 4 *The description of positions 2 and 3 applies analogously for the corresponding contacts and switches of channels B, C, D, E, F, G and H. 4 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
-
Page 5: Connection Example
Fluorescent lamp load AX* 20 A Service life Mechanical lifespan 1,000,000 switch cycles 5 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug... - Page 6 Plastic Dimensions See dimension drawing Weight 604 g Fire load 11 MJ 6 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
- Page 7 All configuration settings are deleted. The building site function of the delivery state is re-activated. 7 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
- Page 8 Using 8-bit scene control switching states can be assigned to a scene and activated again later through the scene. 8 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
- Page 9 Load check normal value Load check above/ Load check below limit Load check contact failure 9 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
-
Page 10: Note On Installation
Note on installation Maximum current via the load terminals ≤ 20 A 10 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug... - Page 11 In case of bus failure/recovery, a manually switched relay is moved into in the parameterized switching state. 11 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug...
-
Page 12: Commissioning And Function Test
44 mm [1.73 in] 61 mm 144 mm [2.40 in] [5.67 in] 12 / 13 Siemens Switzerland Ltd Update: http://www.siemens.com/gamma-td DS01 Building Technologies Division International Headquarters Siemens Switzerland Ltd 2019 Theilerstrasse 1a January 2019 Subject to change CH-6300 Zug... -
Page 13: Product Documentation
+49 911 895-7223 support.automation@siemens.com http://www.siemens.com/supportrequest Technical Support: http://www.siemens.com/supportrequest FAQ: https://support.industry.siemens.com/cs/ww/en/ps/faq Published by: © 2019 Copyright Siemens Switzerland Ltd Siemens Switzerland Ltd Subject to change Building Technologies Division Update: http://www.siemens.com/gamma-td International Headquarters Theilerstrasse 1a CH-6300 Zug January 2019 13 / 13...