Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IBM J02M
Summary of Contents for IBM J02M
- Page 1 IBM Ethernet Router J02M Quick Start GA32-0656-00...
- Page 2 Order publications through your IBM representative or the IBM branch office serving your locality. © Copyright International Business Machines Corporation 2009.
-
Page 3: Table Of Contents
IBM Ethernet Router J02M Quick Start This document describes how to install the IBM Ethernet Router J02M. Contents Copyrights, Trademarks, and Notices ..............2 Copyrights ....................2 Trademarks ....................2 Notices ......................3 Quick Start Description ...................5 Step 1: Prepare the Site ...................6 Rack-Mounting Requirements ..............6 Tools Required ..................7... -
Page 4: Contents Copyrights, Trademarks, And Notices
IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only IBM s product, program or service may be used. Any functionally equivalent product, program or service that does not infringe any of IBM s intellectual property rights may be used instead of the IBM product, program or service. -
Page 5: Notices
Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe on any IBM intellectual property right may be used instead. - Page 6 IBM has not tested those products and cannot confirm the accuracy of performance, compatibility or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products should be addressed to the suppliers of those products.
-
Page 7: Quick Start Description
VPN services, next-generation broadband multiplay services, and high-volume Internet data center internetworking. The IBM Ethernet Router J02M is five rack units (U) tall. Several routers can be stacked in a single floor-to-ceiling open rack, for increased port density per unit of floor space. -
Page 8: Step 1: Prepare The Site
IBM Ethernet Router J02M Quick Start Step 1: Prepare the Site Figure 1: J02M Rack Clearance and Router Dimensions Rack-Mounting Requirements You can install the router in a four-post open rack or open cabinet or an open-frame rack. An empty router weighs 65 lbs (29.5 kg). A fully-populated router weighs 128 lbs (158.1 kg). -
Page 9: Tools Required
Step 1: Prepare the Site The rack rails must be spaced widely enough to accommodate the router chassis's external dimensions: 8.71 in. (22.1 cm) high, 24.5 in. (62.2 cm) deep, and 17.45 in. (44.3 cm) wide. The mounting brackets extend the width to 19 in. -
Page 10: Step 2: Install The Mounting Hardware In A Four-Post Open Rack Or Open Cabinet
IBM Ethernet Router J02M Quick Start Step 2: Install the Mounting Hardware in a Four-Post Open Rack or Open Cabinet To install the mounting shelf on the front rails of a four-post open rack or open cabinet, or the rails of an open-frame rack: If needed, install cage nuts in the holes specified in Table 1 on page 8. - Page 11 Step 2: Install the Mounting Hardware in a Four-Post Open Rack or Open Cabinet Figure 2: Mounting Hardware for a Four-Post Open Rack or Open Cabinet Step 2: Install the Mounting Hardware in a Four-Post Open Rack or Open Cabinet...
-
Page 12: Step 3: Install The Router
Install the Router Using a Lift on page 12 Install the Router Without a Mechanical Lift on page 13 Reinstall Components on page 14 Remove Components Figure 4: Front of the IBM Ethernet Router J02M Step 3: Install the Router... - Page 13 Do not stack removed components. Lay each one on a flat surface. NOTE: For complete instructions about removing router components, see “Installing the Router Without a Mechanical Lift” in the IBM Ethernet Router J02M Hardware Guide. Step 3: Install the Router...
-
Page 14: Install The Router Using A Lift
Ensure that the rack is in its permanent location and is secured to the building. Ensure that the installation site allows adequate clearance for both airflow and maintenance. For details, see the IBM Ethernet Router J02M Hardware Guide. Load the router onto the lift, making sure it rests securely on the lift platform (see Figure 6 on page 12). -
Page 15: Install The Router Without A Mechanical Lift
Step 3: Install the Router Slide the router onto the mounting shelf until the mounting brackets contact the rack rails. The shelf ensures that the holes in the mounting brackets align with the holes in the rack rails. Move the lift away from the rack. Install a mounting screw into each of the open mounting holes aligned with the rack, starting from the bottom. -
Page 16: Reinstall Components
IBM Ethernet Router J02M Quick Start Figure 7: Lift the IBM Ethernet Router J02M into the Rack Reinstall Components Slide each component into the chassis evenly so that it does not become stuck or damaged. Tighten the captive screws for each component. -
Page 17: Connect To A Network For Out-Of-Band Management
Connect the DPC or PIC Cables Have ready a length of the type of cable used by the DPC or PIC. For cable specifications, see the IBM j-type m-series Ethernet Routers DPC Guide or IBM j-type m-series Ethernet Routers PIC Guide. -
Page 18: Step 5: Connect Ground And Power Cables
IBM Ethernet Router J02M Quick Start coiled loop in the cable management system. Placing fasteners on the loop helps to maintain its shape. CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose. -
Page 19: Connect Power To An Ac Router
ESD, see the IBM Ethernet Router J02M Hardware Guide Locate the power cords shipped with the router, which should have a plug appropriate for your geographical location. See the IBM Ethernet Router J02M Hardware Guide. Move the circuit breaker on the power supply faceplate to the off position ( Insert the appliance coupler end of the power cord into the appliance inlet on the power supply. -
Page 20: Connect Power To A Dc Router
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. For more information about ESD, see the IBM Ethernet Router J02M Hardware Guide Switch the circuit breaker on the power supply faceplate to the... - Page 21 Step 5: Connect Ground and Power Cables Remove the clear plastic cover protecting the terminal studs on the faceplate. Secure the power cable lugs to the terminal studs on the power supply, first with the split washer, then with the nut. Apply between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm) of torque.
-
Page 22: Step 6: Perform Initial Software Configuration
IBM Ethernet Router J02M Quick Start Step 6: Perform Initial Software Configuration This procedure connects the router to the network but does not enable it to forward traffic. For complete information about configuring the router to forward traffic, including examples, see the JUNOS software configuration guides. - Page 23 Step 6: Perform Initial Software Configuration root@# set system root-authentication plain-text-password New password: password Retype new password: password [edit] root@# set system root-authentication encrypted-password encrypted-password [edit] root@# set system root-authentication ssh-dsa public-key [edit] root@# set system root-authentication ssh-rsa public-key Optionally, display the configuration to verify that it is correct. [edit] root@# show system {...
-
Page 24: Safety Warnings
Read the installation instructions before you connect the router to a power source. Before installing the router, read the guidelines for site preparation in the IBM Ethernet Router J02M Hardware Guide to make sure that the site meets power, environmental, and clearance requirements for the router. - Page 25 IBM Ethernet Router J02M Hardware Guide. To prevent injury, keep your back straight and lift with your legs, not your back. Do not attempt to lift the chassis by the power supply handles.
-
Page 26: Hardware Service And Support
For information about which products are supported by Support Line in your country or region, go to the following Web site: www.ibm.com/services/sl/products For more information about the IBM Support Line and other IBM services, go to the following Web sites: www.ibm.com/services www.ibm.com/planetwide... - Page 27 Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
- Page 28 Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu ® installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der IBM verändert bzw.
- Page 29 People’s Republic of China Class A Electronic Emission Statement Japan VCCI Class A ITE Electronic Emission Statement Korea Class A Electronic Emission Statement Taiwan Contact Information IBM Taiwan Product Service Contact Info: IBM Taiwan Corporation 3F, No 7, Song Ren Rd., Taipei Taiwan Tel: 0800-016-888...
- Page 30 Your feedback is important in helping us provide the most accurate and high-quality information. If you have comments or suggestions for improving this document, send us your comments by e-mail to starpubs@us.ibm.com. Be sure to include the following: v Exact publication title...
- Page 32 Part Number: 45W5526 Printed in USA GA32-0656-00...