hit counter script
Sony HDC4300 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. CCD Cameras
  5. super motion hdc4300
  6. Service manual

Sony HDC4300 Service Manual

Hide thumbs Also See for HDC4300:
Table of Contents

Advertisement

Quick Links

Download this manual
COLOR CAMERA
HDC4300
SERVICE MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony HDC4300

Summary of Contents for Sony HDC4300

  • Page 1 COLOR CAMERA HDC4300 SERVICE MANUAL 1st Edition...
  • Page 2 à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. Model Name Serial No. HDC4300 (SY) 10001 and Higher HDC4300 (CED) 40001 and Higher HDC4300 (J)
  • Page 3 The use of optical instruments with this product will increase eye hazard. CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT This HD COLOR CAMERA is classified as a CLASS 1 LASER PRODUCT. HDC4300...
  • Page 4 Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. HDC4300...

  • Page 5: Table Of Contents

    When the Optical Connector Cleaner (Commercially Available) is not Available (Tajimi Electronics Co., Ltd.)..2-6 2-4-4. When the Optical Connector Cleaner (Commercially Available) is not Available (Connector)..... . . 2-8 HDC4300...
  • Page 6 SW-1530 Board/SW-1530A Board................. . . 4-53 HDC4300...
  • Page 7 Forced Version Update of Software or PLD Data..............6-5 HDC4300...
  • Page 8 Outside-3 ......................... . . 10-6 HDC4300...
  • Page 9 Frame Wiring......................... . 11-4 HDC4300...

  • Page 11: Manual Structure

    Related manuals The following manuals are available for this model. If any of these manuals is required, please contact your local Sony Sales Office/Service Center. • Operation Manual CD-ROM (Supplied with this unit) This manual contains information required to operate and use the unit.

  • Page 13: Service Overview

    If the ROM and software version is lower than the specified below, be sure to perform ROM replacement and updating the software. If ROM replacement and updating the software are required, contact your local Sony Sales Office/Service Center. Peripheral Equip- Board Name Ref.

  • Page 14: Connectors And Cables

    0.8 Vp-p 75 Ω, 1.485 Gbps/1.4835 Gbps Serial TEST OUT SDI 2 BNC type 75 Ω, 1.0 V p-p BNC type EARPHONE Output: HD SDI signal SMPTE 292M/372M, BTA-S004 compliant Stereo mini jack 0.8 Vp-p 75 Ω, 2.97 Gbps/2.9679 Gbps Serial HDC4300...
  • Page 15 –60 dBu, –50 dBu, — No connection –40 dBu, –30 dBu, AUDIO 1/2 (X) UNREG +12 V dc, 500 mA (max) –20 dBu selectable, High AUDIO 1/2 (Y) impedance, Balanced 　 　 11. REMOTE 8-pin, Female - External View - HDC4300...
  • Page 16 - External View - — No connection — No connection Signal Specifications G TALLY ON : 5 V RET VIDEO • ENABLE: 0 V OFF : GND ENABLE • DISABLE: +5 V or — No connection OPEN — No connection Continued Continued HDC4300...
  • Page 17 RS-232C • RX0 (+): RS-422A • RX1: for RS-232C GND (VIDEO) — GND for VIDEO - External View - Y VIDEO (X) 1.0 V p-p, (0 dBu = 0.775 V rms) Zo = 75Ω — GND for SCL/SDA Continued HDC4300...

  • Page 18: Wiring Diagrams For Cables

    Data - (3) 1-2-3. Connection Connectors/Cables 22. DC OUT Connection made with the connector panels during installation or 2-pin, Female service, should be made with the connectors/complete cable assemblies specified in the following list, or equivalent parts. - External View - HDC4300...

  • Page 19: Note In Connecting Bpu Connector

    “2-4. Cleaning of Connector/Cable”. If using a cable of length different from a standard product, contact your local Sony Sales Office/Service Center. The pin 8 of CCA-5 cable is GND (ground). The pin 8 of REMOTE cable is not GND (ground).

  • Page 20: Location Of Printed Circuit Boards

    1-3. Location of Printed Circuit Boards BI-291 IF-1278 DR-663 BI-291 SE-1093 DPR-370 PS-836 RE-291 SY-408 CN-3426 SW-1672 CN-3421 SW-1531 CN-3423 MB-1214 AT-189 SW-1528 SW-1527 CN-3424 HDC4300...
  • Page 21 SW-1530: SY, J CN-3430 SW-1530A: CED, CN CN-3429 CN-3428 LE-376 TX-146 SW-1524 CN-3422 CN-3431 SW-1525 CN-3427 MEM-147 CN-3432 CN-3425 CN-3434 HDC4300...

  • Page 22: Notes On Board Replacing

    The part number listed in “10. Spare Parts” is for EEPROM which is not programmed. If replacement is needed, contact your local Sony Sales Office/Service Center. 1-4-2. Adjustment and Setting Required when Replacing the SY-408 Board Camera setting status and files are stored in the SY-408 board. When the SY-408 board is replaced, contents of the reference file, scene file, lens file, and operator file are lost.

  • Page 23: Fixtures/Measuring Equipments List

    LEADER ELECTRONICS LV5150DA, LV5152DA or equivalent Frequency counter Advantest TR5821AK or equivalent Digital voltmeter Advantest TR6845 or equivalent HD color monitor Sony BVM-D20F1J/D14H5J or equivalent Luminance meter Konica Minolta LS-110 or equivalent Spectrum analyzer Advantest R3131A or equivalent Signal generator...

  • Page 24: Microphone Power And Intercom Settings

    In the case of dual-type headphone to listen the same sound with both ears or single-type headphone Set “INTERCOM RECEIVE SELECT” on the RECEIVE SEL page of the OPERATION menu to “MIX”. The same sound is output from right and left. 1-12 HDC4300...
  • Page 25 Set channels (left, right, and both) of items INTRECOM, PGM1, PGM2, and TRACKER on the RECEIVE SEL page. To adjust the volume of your voice Set volume in SIDE TONE on the INTERCOM LEVEL page of the OPERATION menu. 1-13 HDC4300...

  • Page 26: Flexible Card Wire And Coaxial Cable

    Slide or lift up the portion A in the direction of the arrow to unlock and pull out the flexible card wire. Connecting Insert the flexible card wire firmly as far as it will go with the insulating surface facing upward. 1-14 HDC4300...

  • Page 27: Forming Flexible Card Wire

    CN-3427 board • SY-408 board CN5 ↔ SW-1530 board CN1 24 mm Isolation surface 45° Mountain Valley fold fold SW-1530 board SY-408 board • SY-408 board CN9 ↔ CN-3426 board CN1 Isolation surface Valley Valley Mountain fold fold fold 1-15 HDC4300...

  • Page 28: Disconnecting/Connecting Fine-Wire Coaxial Cable

    Hold both sides of the fine-wire coaxial cable connector, and pull the connector in the arrow direction to disconnect Connecting Both sides of connector Fine-wire coaxial cable Insert the connector of fine-wire coaxial cable in the arrow direction to connect it. Note Insert firmly the connector of fine-wire coaxial cable in the interior. 1-16 HDC4300...

  • Page 29: Connecting/Disconnecting Coaxial Cable

    Hold both sides of the fine-wire coaxial cable connector with the contact surface facing up. Insert the connector straight to meet the angle specified. 1-7-4. Connecting/Disconnecting Coaxial Cable Type A Disconnecting Hold the plug to remove. Do not attempt to remove by pulling the cable. Hold the plug of coaxial cable. 1-17 HDC4300...
  • Page 30 Be sure to hold the plug when disconnecting the coaxial cable. Do not pull the cable. Connecting Hold the plug to connect Connecting connector Hold the plug of coaxial cable. Connect the coaxial cable perpendicularly to the connector. Push the plug into the connector while turning it clockwise and counterclockwise several times. 1-18 HDC4300...

  • Page 31: Explanation Of Prism Number

    1-8. Explanation of Prism Number The CMOS imager adhering to prism is managed by following mount assembly number. A-2075-369-A Example : A00000001 to (8 digit) 1-19 HDC4300...

  • Page 32: Circuit Protection Parts

    THP601 B3 (Side B) 1-803-615-21 0.14 A/20 ℃ THP602 A1 (Side B) 1-803-353-21 0.50 A/20 ℃ THP603 B1 (Side B) 1-803-615-21 0.5 A/20 ℃ MEM-147 THP001 1-803-615-21 0.5 A/20 ℃ THP002 1-803-615-21 0.5 A/20 ℃ THP003 1-803-615-21 Continued 1-20 HDC4300...
  • Page 33 Part No. Hold Current Name 1.10 A/20 ℃ SY-408 THP1 B3 (Side A) 1-802-063-21 0.50 A/20 ℃ THP101 C3 (Side A) 1-803-615-21 0.50 A/20 ℃ THP102 D2 (Side B) 1-803-615-21 0.50 A/20 ℃ THP103 D2 (Side B) 1-803-615-21 1-21 HDC4300...

  • Page 34: Lead-Free Solder

    • The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-22 HDC4300...

  • Page 35: Periodic Maintenance And Inspection

    Replace it as nec- Fan Duct 4-572-051-01 essary. DC OUT Connector Cap 4-415-079-01 SW Cover 4-138-682-01 BNC Cap 3-872-935-01 BNC Cap 3-868-657-03 Rear Connector Cap 2 4-414-618-01 Rear Connector Cap 1 4-414-617-01 DC Fan 1-855-374-11 Cushion (FAN) 4-546-928-01 HDC4300...

  • Page 36: Cleaning The Air Vents

    Clean the air vents every two or three months. Loosen the two screws with stopper, and remove the shoulder pad assembly. Remove dust on the air vent areas with a vacuum cleaner. Air vent Shoulder pad assembly Air vent Screws with stopper HDC4300...

  • Page 37: Replacing Lithium Battery

    A lithium battery is mounted on the SY-408 board to back up the real time clock (RTC). If a battery comes to the lifetime, then RTC stops. Therefore, the battery must be replaced. • SY-408 board/Lithium secondary battery (ML621 (U)): Sony Part No. 1-756-134-15 CAUTION In replacing, ensure that the battery is installed with “+”...

  • Page 38: Cleaning Of Connector/Cable

    Clean the tip of the white optical contacts using the optical connector cleaner. Optical contacts (white) Female connector Insert the optical connector cleaner straight. Apply sufficient pressure (approximately 600 g to 700 g) to ensure that the optical contact is a little depressed. HDC4300...

  • Page 39: When The Optical Connector Cleaner (Commercially Available) Is Not Available (Connectors/Cables Of Lemo)

    Clean the LEMO connectors and cables using the following procedure. Fixtures • Alignment sleeve remover HC-001 (for female connector) Sony Part No. : J-6480-010-A or DCC.91.312.5LA manufactured by LEMO, or equivalent Note Insert the shorter nose end when removing/installing the alignment sleeve. Grasp not the shock absorber portion of the remover but the handle in use.

  • Page 40: When The Optical Connector Cleaner (Commercially Available) Is Not Available (Tajimi Electronics Co., Ltd.)

    The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve. Alignment sleeve: Sony Part No. : 9-980-074-01 Alignment sleeve Clean the tip of the white optical contacts with a cotton swab moistened with alcohol.
  • Page 41 If there is no screwdriver, use the plate attached to the connector cap. Pull the adapter pin out of the connector in the arrow direction. Adapter Adapter pin Clean the white optical contacts with a cotton swab moistened with alcohol. Optical contacts (white) HDC4300...

  • Page 42: When The Optical Connector Cleaner (Commercially Available) Is Not Available (Connector)

    Cleaning Procedure Clean the tip of the white optical contacts with a cotton swab moistened with alcohol. Optical contact (white) HDC4300...
  • Page 43 Connect 2 pin harnesses harnesses (BLK,BRN) (BLK,BRN) of FB cable of FB cable detection detection. connect? Confirm CHU MODE of BPU menu C07 Is configuration Set C07 CHU MODE in of BPU set to BPU menu to HDC4300. HDC4300? HDC4300...
  • Page 44 25P, 24P, 23.98P with 3G, the picture does not output correctly. The levels are changed after changing Rch at WB adjustment. Confirm the 4K COLOR SPACE setting of BPU menu C08. Is it set to NORMAL? Set it to NORMAL. HDC4300...
  • Page 45 POWER LED of BPU turn on? Confirm the connection of AC input cable. Does camera turn on? Does POWER LED of CAMERA turn on? Remove the accessories attached to the camera, turn on in the following sequence CCU, BPU and camera. HDC4300...

  • Page 47: Replacement Of Main Parts

    DC Fan (Front) “4-9. DC Fan (Front)” (13) DC Fan (Rear) “4-10. DC Fan (Rear)” Mounted circuit boards After replacing/repairing the mounted circuit boards (or the assembling parts including them), perform the steps after replacement/repair. (Refer to“1-4. Notes on Board Replacing”) HDC4300...
  • Page 48 CN-3427 board “4-11-1. CN-3429 Board/CN-3427 Board” （8） CN-3428 board “4-11-3. PROMPTER/GENLOCK/TEST OUT Connector （9） (CN-3428 Board)” （10） CN-3429 board “4-11-1. CN-3429 Board/CN-3427 Board” CN-3430 board “4-11-4. REMOTE Connector (CN-3430 Board)” （11） CN-3431 board “4-12-1. INTERCOM Connector (CN-3431 Board)” （12） Continued HDC4300...

  • Page 49: Basic Knowledge

    • Since small screws are used in this unit, they may fall into the unit when they are removed and installed. To prevent screws from falling, it is recommended that the bit of each torque driver be magnetized to a degree that prevents screws from falling. HDC4300...

  • Page 50: Inside Panel Assembly

    Inside panel assembly Inside SW cover Screws with stopper Switch levers Note Turn the switch levers in the arrow direction, and then install the inside panel assembly. Install the inside panel assembly and tighten the four screws with stopper. HDC4300...

  • Page 51: Outside Block

    Disconnect the harness from the connector (CN100) on the PS-836 board. Disconnect the two fine-wire coaxial cables from the two connectors (CN800, CN203) on the DPR-370 board. Disconnect the two FPCs with connector (DPR-SDI) from the two connectors (CN104, CN105) on the DPR-370 board. HDC4300...
  • Page 52 When installing the outside panel assembly, arrange the harness as shown in the figure. Remove the outside panel support from the hook of the main frame and remove the outside panel assembly. Outside panel support Hook of main frame Outside panel assembly HDC4300...

  • Page 53: Mem-147 Board/Tx-146 Board

    Release the fine-wire coaxial cable and coaxial cables from the clamper. Disconnect the three coaxial cables from the three connectors (SDI1, SDI2, and PROMPTER2) on the MEM-147 board. Disconnect the fine-wire coaxial cable from the connector (CN501) on the MEM-147 board. HDC4300...
  • Page 54 CN1001 Clamper Fine-wire coaxial cables CN-3434 board Note When connecting the coaxial cables, connect connectors correctly. Remove the seven screws, and open the MEM-147 board in the direction of the arrow. PSW3 x 6 PSW3 x 6 MEM-147 board HDC4300...
  • Page 55 • When installing the MEM-147 board, match the two bosses with the two holes. • When installing the MEM-147 board, arrange the optical fiber cables as shown in the figure. Remove the radiation sheet (EC rear) from the TX-146 board. HDC4300...

  • Page 56: Dc Fan (Outside Panel)

    15. Install the removed parts by reversing the steps of removal. 4-3-3. DC Fan (Outside panel) Preparation Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Remove the MEM-147 board assembly. (Refer to “4-3-2. MEM-147 Board/TX-146 Board”) 4-10 HDC4300...

  • Page 57: Cn-3434 Board

    Install the removed parts by reversing the steps of removal. 4-3-4. CN-3434 Board Preparation Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Procedure Remove the UL tape from the CN-3434 board. Disconnect the fine-wire coaxial cable from the connector (CN001) on the CN-3434 board. 4-11 HDC4300...

  • Page 58: Optical Multi Cable Assembly

    Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Remove the MEM-147 board assembly. (Refer to“4-3-2. MEM-147 Board/TX-146 Board”) Procedure Remove the screw, and detach the earth lug. Remove the tape AS. Release the two optical fiber cables from the clamper. 4-12 HDC4300...

  • Page 59: Prompter Connector

    Install the removed parts by reversing the steps of removal. 4-3-6. PROMPTER Connector Preparation Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Procedure Remove the two screws, and detach the BNC cap, and bracket BNC. Disconnect the coaxial cable from the PROMPTER connector. 4-13 HDC4300...

  • Page 60: Coaxial Cable

    Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Remove the MEM-147 board assembly. (Refer to“4-3-2. MEM-147 Board/TX-146 Board”) Procedure Disconnect the coaxial cable from the connector (SDI1). Remove the four screws, and detach the two BNC caps, and two brackets BNC. 4-14 HDC4300...
  • Page 61 Remove the two nuts and two washers, and detach the coaxial cable (SDI2). Brackets BNC Coaxial cable Washers Coaxial cable (SDI1) Connector (SDI2) B2 x 5 B2 x 5 BNC caps Install the removed parts by reversing the steps of removal. 4-15 HDC4300...

  • Page 62: Fd (Filter Disk) Assembly

    Disconnect the harness from the connector (CN3) on the IF-1278 board. Loosen the two screws, and detach the FD assembly. FD assembly IF-1278 board Harness Attached screws (Tightening torque: 0.53 N•m) Install the removed parts by reversing the steps of removal. 4-16 HDC4300...

  • Page 63: Front Assembly

    CN202 Hook CN201 Grooves Hooks Hook CN200 CN300 Fine-wire coaxial cables Note When installing the front assembly, arrange the fine-wire coaxial cables as shown in the figure. Loosen the four screws with stopper, and draw the front assembly. 4-17 HDC4300...
  • Page 64 Disconnect the harness from the connector (CN303) on the DPR-370 board. CN303 (DPR-370 board) Screws with stopper Front assembly Harness Screws with stopper Install the removed parts by reversing the steps of removal. 4-18 HDC4300...

  • Page 65: Ohb Block

    (Tightening torque: 0.53 N•m) Remove the four screws and four washers, and detach the front panel assembly. Front panel assembly OHB assembly M3 x 8 (Tightening torque: 1.1 N•m) Install the removed parts by reversing the steps of removal. 4-19 HDC4300...

  • Page 66: If-1278 Board

    CN005 Remove the four screws, and draw the IF-1278 board. Disconnect the harness from the connector (CN004) on the IF-1278 board. IF-1278 board PSW2 x 5 Harness CN004 Install the removed parts by reversing the steps of removal. 4-20 HDC4300...

  • Page 67: Handle Block

    Remove the screw, and detach the LE-376 board. Remove the toggle SW cushion. Disconnect the harness from the connector (CN2) on the SW-1524 board. Remove the screw, and pull up the SW-1524 board in the direction of arrow. 4-21 HDC4300...

  • Page 68: Vf Connector (Cn-3422 Board)

    Install the removed parts by reversing the steps of removal. 4-7-2. VF Connector (CN-3422 Board) Procedure Remove the front assembly. (Refer to“4-5. Front Assembly” on page 4-17 Procedure Press the handle release button and turn the handle in the direction of arrow. 4-22 HDC4300...
  • Page 69 Remove the two screws, and detach the top cover. B2 x 5 Handle release button Top cover Handle Remove the three screws, and pull up the handle assembly. 4-23 HDC4300...
  • Page 70 SW-1525 board Disconnect the harness from the connector (CN2) on the CN-3422 board. Remove the two screws, and detach the CN-3422 board. B2.6 x 5 harness CN-3422 board Install the removed parts by reversing the steps of removal. 4-24 HDC4300...

  • Page 71: Sw-1525 Board

    When installing the SW-1525 board to the SW-1525 bracket, match the boss with the slit. When installing the SW-1525 bracket to the main unit, match the two bosses with the two holes. Install the removed parts by reversing the steps of removal. 4-25 HDC4300...

  • Page 72: Main Chassis Block

    Disconnect the nine harnesses from the nine connectors (CN1 to CN4, CN6, CN7, and CN10 to CN12) on the SY-408 board. Harness Flexible flat cable Harnesses Harnesses CN10 CN11 CN12 Flexible flat cables SY-408 board Harnesses Remove the five screws. Remove the SY-408 board from the connector (CN101) on the MB-1214 board. 4-26 HDC4300...

  • Page 73: Power Block Assembly (Re-291 Board/Ps-836 Board)

    Assembly”) Remove the SY-408 Board. (Refer to“4-8-1. SY-408 Board/AT-189 Board”) Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Procedure Disconnect the harness from the connector (CN6002) on the RE-291 board. Release the harness from the clamper. 4-27 HDC4300...
  • Page 74 Remove the three screws, and detach the power block assembly from the connector (CN4) on the MB-1214 board in the direction of arrow. Power block assembly PSW3 x 6 MB-1214 board Remove the screw, and detach the pin stopper. 4-28 HDC4300...
  • Page 75 Remove the two screws, and detach the RE-291 board from the connector (CN5007) on the PS-836 board. PSW3x 6 RE-291 board PS-836 board CN5007 Remove the screw, and detach the heat sink retainer and thermal sheet. Remove the hexagon support. 10. Remove the four screws, and detach the PS-836 board. 4-29 HDC4300...

  • Page 76: Dpr-370 Board

    12. Install the removed parts by reversing the steps of removal. 4-8-3. DPR-370 Board Preparation Remove the inside panel assembly. (Refer to“4-2. Inside Panel Assembly”) Remove the outside panel assembly. (Refer to“4-3-1. Outside Panel Assembly”) Remove the front assembly. (Refer to“4-5. Front Assembly”) 4-30 HDC4300...
  • Page 77 Coaxial cable CN801 CN106 CN107 Harnesses CN102 Boss (MB-1214 board) PSW3 x 6 Holes DPR-370 board PSW3 x 6 Note When installing the DPR-370 board, match the two bosses with the two holes. Remove the DPR thermal sheet. 4-31 HDC4300...

  • Page 78: Mb-1214 Board

    Remove the DPR-370 board. (Refer to“4-8-3. DPR-370 Board”） Procedure Disconnect the three harnesses from the three connectors (CN6, CN7, and CN9) on the MB-1214 board. Remove the counter measure sheet from the connector (CN1) on the MB-1214 board. 4-32 HDC4300...
  • Page 79 Remove the two screws, and detach the MB bracket. Disconnect the two harnesses from the two connectors (CN5, CN8) on the MB-1214 board. Harness Harness Boss MB-1214 board MB bracket Hole PSW2 x 5 Note When installing the MB bracket, match the boss with the hole. 4-33 HDC4300...

  • Page 80: Sw-1527 Board

    Remove the toggle SW cushion (C), two toggle SW cushions, VR knob (audio), and front shield plate. Remove the two screws (PSW2 x 5) and pull out the SW-1527 board in the direction of arrow. Disconnect the harness from the connector (CN1) on the SW-1527 board. 4-34 HDC4300...

  • Page 81: Cn-3423 Board

    When installing the SW-1527 board, match the two bosses with the two holes. Install the removed parts by reversing the steps of removal. 4-8-6. CN-3423 Board Preparation Remove the SW-1527 Board. (Refer to “4-8-5. SW-1527 Board”.) Procedure Remove the screw and pull out the CN-3423 board. 4-35 HDC4300...

  • Page 82: Sw-1672 Board

    Disconnect the harness from the connector (CN001) on the SW-1672 board. Harness CN001 Boss PSW2 x 5 Slit SW-1672 board Note When installing the SW-1672 board, match the boss with the slit. Install the removed parts by reversing the steps of removal. 4-36 HDC4300...

  • Page 83: Cn-3421 Board

    Install the removed parts by reversing the steps of removal. 4-8-9. SW-1528 Board Preparation Remove the inside panel assembly. (Refer to “4-2. Inside Panel Assembly”.) Procedure Remove the five toggle SW cushions. Remove the screw and pull out the SW-1528 board in the direction of arrow. 4-37 HDC4300...

  • Page 84: Cn-3424 Board

    Remove the front assembly. (Refer to “4-5. Front Assembly”.) Remove the SW-1672 board. (Refer to“4-8-7. SW-1672 Board”) Remove the SW-1528 board. (Refer to “4-8-9. SW-1528 Board”.) Remove the SW-1527 board. (Refer to“4-8-5. SW-1527 Board”) Remove the CN-3423 board. (Refer to“4-8-6. CN-3423 Board”) 4-38 HDC4300...
  • Page 85 Arrangement the harnesses from the CN-3424 board Harness Harnesses Harnesses CN-3424 board Note When installing the CN-3424 board, arrange the harnesses as shown in the figure. Disconnect the five harnesses from the five connectors (CN1 to CN5) on the CN-3424 board. 4-39 HDC4300...

  • Page 86: Cn-3426 Board

    Remove the two screws, and detach the CN-3426 board. Boss CN-3426 board PSW2 x 5 Hole Flexible flat cable Note When installing the CN-3426 board, match the boss with the hole. Install the removed parts by reversing the steps of removal. 4-40 HDC4300...

  • Page 87: Sw-1531 Board

    Assembly”) Remove the SY-408 board. (Refer to“4-8-1. SY-408 Board/AT-189 Board”） Remove the DPR-370 board. (Refer to“4-8-3. DPR-370 Board”） Procedure Disconnect the harness from the connector (CN101) on the PS-836 board, and release the harness from the two clampers. 4-41 HDC4300...
  • Page 88 Disconnect the harness from the connector (CN6) on the MB-1214 board, and release the harness from the two clampers. CN101 Harnesses Clamper Harness Harness PS-836 board Clamper Clamper MB-1214 board Clamper Harnesses Remove the four screws, and detach the hotshoe assembly. Hotshoe assembly B3 x 8 B3 x 8 4-42 HDC4300...
  • Page 89 Remove the two screws, and detach the BUILD UP connector. BUILD UP connector Step screws (attached screw) Install the removed parts by reversing the steps of removal. 4-43 HDC4300...

  • Page 90: Dc Fan (Front)

    The OHB sliding sheet is attached to the SUB frame. When removing it, be careful not to damage the SUB frame. Remove the DC fan (front) assembly. Harness OHB sliding sheet DC fan (front) assembly SUB frame MB-1214 board Clamper 4-44 HDC4300...
  • Page 91 Remove the DC fan (front) from the cushion (fan). Cushion (fan) Label DC fan (front) Harness Note When installing the DC fan (front), carefully peeling off it paying attention to the label and harness locations. Install the removed parts by reversing the steps of removal. 4-45 HDC4300...

  • Page 92: Dc Fan (Rear)

    Remove the DC fan (rear) from the fan duct. DC fan (rear) Fan duct Label Harness Note When installing the DC fan (rear), carefully install it paying attention to the label and harness locations. Install the removed parts by reversing the steps of removal. 4-46 HDC4300...

  • Page 93: Mic Panel Block

    Disconnect the two harnesses from the two connectors (CN10, CN12) on the SY-408 board. CN12 CN10 Flexible flat cable (36 core) SY-408 board Harnesses Remove the five screws and pull out the MIC panel assembly. Disconnect the harness from the connector (CN2) on the CN-3432 board. 4-47 HDC4300...
  • Page 94 PSW2 x 5 Disconnect the flexible flat cable from the connector (CN1) on the CN-3427 board. 10. Remove the UL tape. 11. Disconnect the three harnesses from the three connectors (CN2 CN3 and CN6) on the CN-3427 board. 4-48 HDC4300...

  • Page 95: Audio In Connector (Cn-3425 Board)

    13. Install the removed parts by reversing the steps of removal. 4-11-2. AUDIO IN Connector (CN-3425 Board) Preparation Remove the MIC panel assembly. (Refer to“4-11-1. CN-3429 Board/CN-3427 Board” on page 4-47 Procedure Remove the four screws, and detach the CN-3425 board. 4-49 HDC4300...

  • Page 96: Prompter/Genlock/Test Out Connector (Cn-3428 Board)

    B2 x 5 BNC cap B2 x 5 PROMPTER/GENLOCK/TEST OUT connector (CN-3428 board) Install the removed parts by reversing the steps of removal. 4-11-4. REMOTE Connector (CN-3430 Board) Preparation Remove the MIC panel assembly. (Refer to“4-11-1. CN-3429 Board/CN-3427 Board” on page 4-47 4-50 HDC4300...

  • Page 97: Dc In Connector (Cn-3432 Board)

    Remove the two screws, and detach the DC IN connector (CN-3432 board). Disconnect the harness from the connector (CN2) on the DC IN connector (CN-3432 board). B2.6 x 5 DC IN connector (CN-3432 board) Harness Install the removed parts by reversing the steps of removal. 4-51 HDC4300...

  • Page 98: Incom Panel Assembly

    When connecting the two harnesses, pay attention to their colors. Remove the six screws, and detach the INCOM panel assembly. B2 x 5 B2 x 5 B2 x 5 B2 x 5 INCOM panel assembly Remove the four screws, and detach the two INTERCOM connectors (CN-3431 boards). 4-52 HDC4300...

  • Page 99: Sw-1530 Board/Sw-1530A Board

    Remove the two return select knobs. Remove the six VR knobs. Remove the screw, and detach the DC line protection sheet. Remove the two screws, and detach the SW-1530 board. Disconnect the flexible flat cable from the connector (CN1) on the SW-1530 board. 4-53 HDC4300...
  • Page 100 • When installing the return select knob, set the marks of the switch and the return select knob on the SW-1530 board to the positions shown in the figure. • When installing the return SEL packing, stick the adhesive surface to the board side. Install the removed parts by reversing the steps of removal. 4-54 HDC4300...

  • Page 101: Electrical Alignment

    Use calibrated equipment and tools. Equipment Required Name Equipment HD waveform monitor Leader Electronics LV5150DA, Leader Electronics LV5152DA (multi format) or equivalent HD color monitor Sony BVM-D20F1J/BVM-D14H5J or equivalent Oscilloscope Tektronix TDS460A or equivalent Master setup unit Sony MSU-1000/1500 HD viewfinder Sony HDVF-20A/200/C30WR/C35W Lens...

  • Page 102: Handling The Grayscale Chart

    • When the chart is not used for a long period and is stored, open the case and dry the chart for about an hour once or twice a month. Setting Illumination Measuring equipment : Illuminance meter (Calibrated) Procedure Turn on the light source. HDC4300...
  • Page 103 Illuminance meter Light source Transparent grayscale chart (16:9) Recommended chart • Product name: Grayscale chart (16:9 transparent type) • Sony Part No.:J-6394-080-A Handling precautions Use calibrated pattern box. Setting Illumination Measuring equipment : Illuminance meter (KONICA MINOLTA LS-110 or equivalent , Calibrated) Preparation Place the pattern box where the chart is not exposed to light, such as a darkroom.

  • Page 104: Setup Menu

    Set the DISPLAY switch to “MENU” while pressing the ASSIGNABLE 1 switch on the side of the camera and the rotary encoder on the front of the camera. [SERVICE] menu is displayed on the [TOP MENU] screen. Display screen of [SERVICE] menu, Refer to “8-2. SERVICE Menu”. HDC4300...

  • Page 105: Connection Of Equipment

    Change: Turn the rotary encoder. Confirm: Press the rotary encoder. Cancel: Switch the STATUS/CANCEL to "CANCEL”. Before confirming, value can be returned to previous. 5-1-5. Connection of Equipment Viewfinder HDVF-20A/200/C30WR/C35W HDC4300 Lens (For ENG/EFP) Waveform monitor A-ch SDI MONI Y, Pb, Pr...

  • Page 106: Setup Menu Correspondence List

    Setup Menu Correspondence List The camera setup menu items corresponding to the adjustment items of MSU are described. Refer to the following tables when using the camera setup menu for electrical adjustments without using MSU PAINT • MSU： [PAINT] button → ON(lit). HDC4300...
  • Page 107 Ref Store FILE REFERENCE STORE FILE Lens File Lens Store LENS FILE STORE FILE OHB File OHB Store OHB FILE STORE FILE MAINTENANCE • MSU : [MAINTENANCE] button → ON (lit) • Camera setup menu : Select [MAINTENANCE] menu HDC4300...
  • Page 108 H PARA H PARA R/G/B V SAW V SAW R/G/B V PARA V PARA R/G/B Lens Auto Iris Settings Level AUTO IRIS IRIS LEVEL APL Ratio APL RATIO V Mod Saw R/G/B PAINT VIDEO LEV- V MOD R/G/B/M Master HDC4300...

  • Page 109: Automatic Adjustment

    START/BREAK button lights (ON), automatic adjustment is executed. After the adjustment is completed, the message “Completed” is displayed. When performing automatic adjustment using the camera menu, set the setup menu as follows. MENU: MAINTENANCE PAGE: AUTO SETUP ITEM: AUTO LEVEL HDC4300...

  • Page 110: Camera System Adjustment

    • 4K59.94P (2x) • HD59.94P (2x) • HD59.94P (4x) • HD59.94P (8x) File store MENU：SERVICE PAGE：BLACK SHADING ITEM：STORE FILE 5-3-2. Sensitivity Adjustment Measuring equipment : waveform monitor (R,G,B) Measuring point : SDI 1 terminal Subject : Grayscale chart 5-10 HDC4300...
  • Page 111 Adjust [R1] and [R2] of [GAIN CONT] so that A portion level of R channel waveform becomes 100%. The values of [R1] and [R2] should be same. Adjust [G1],[G2],[B1] and [B2] of [GAIN CONT] in the same way as step 8. 100% 10. Store the file. MENU：SERVICE PAGE：OHB_ADJ1 ITEM：STORE FILE 5-11 HDC4300...

  • Page 112: Black Shading Adjustment

    GAMMA OFF button → OFF (lit) MASTER GAIN → 12 MASTER BLACK → 30 Procedure Set as follows by camera setup menu. MENU：MAINTENANCE PAGE：OUTPUT FORMAT ITEM：CURRENT → 4K59.94P Set as follows by camera setup menu. MENU：SERVICE PAGE：BLACK SHADING ITEM：MONITOR SEL → R 5-12 HDC4300...

  • Page 113: White Shading Adjustment

    When the next condition corresponds to even one, white shading is not adjusted correctly. Note • The brightness of the subject is uneven. • The brightness is not set correctly. • Iris value of lens is not set correctly. • Zoom position is not set correctly. 5-13 HDC4300...
  • Page 114 WHITE button → ON (lit) After the adjustment is completed, the message "AWB : OK" is displayed. Open the following items with using the MSU. (1) MAINTENANCE button → ON (lit) (2) Touch panel operation: [Camera] → [White Shading] → [R] 5-14 HDC4300...
  • Page 115 After the adjustment is completed, the message “AWB : OK” is displayed. Set the lens extender to ×1. Operate the control panel of MSU, and store the lens file. (1) FILE button → ON (lit) (2) Touch panel operation : [Lens File] → [Lens Store] → [Store] 5-15 HDC4300...
  • Page 116 (1) FILE button → ON (lit) (2) Touch panel operation : [Lens File] → [Lens Store] → [Store] Return the setting of lens extender or lens shrinker. • Lens extender (×2) → OFF • Lens shrinker (×0.8) → OFF 5-16 HDC4300...

  • Page 117: Video System Level Adjustment

    Set each item as follows: • Level → 99 • Limiter → 0 • Crispening → –25 • Level Dep → 25 Operate the [PAINT] menu of MSU, and set as follows. Touch panel operation: (Page 1) → [Detail] → [2/3] 5-17 HDC4300...

  • Page 118: Detail Level Adjustment

    (2) Touch panel operation: (Page 1) → [Detail] → [1/3] Adjust the detail level to be added to each step of the grayscale to the desired level. • Adjustment item : [Level] Store the reference file. (Refer to the “5-4-12. File Store”. 5-18 HDC4300...

  • Page 119: Crispening Adjustment

    Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector Object: Grayscale chart Preparation • Setting for MSU DETAIL OFF button → ON (dark) • Shoot the grayscale chart so that the chart frame is aligned with the under scanned monitor frame. 5-19 HDC4300...

  • Page 120: Detail Clip Adjustment

    • Setting for DETAIL OFF button → ON (dark) KNEE OFF button → OFF (lit) • Shoot the grayscale chart so that the chart frame is aligned with the under scanned monitor frame. • Lens iris: F4 to F5.6 5-20 HDC4300...
  • Page 121 Adjust the edge at portion B(white) to the desired clip level. • Adjustment item : [W Limiter] Adjust the edge at portion C(black) to the desired clip level. • Adjustment item : [B Limiter] Store the reference file. (Refer to the “5-4-12. File Store”. 5-21 HDC4300...

  • Page 122: Auto-Iris Adjustment

    Equipment: Waveform monitor (R, G, B) Test Point: SDI 1 connector Preparation • Setting for MSU CLOSE button → ON (lit) • Shoot the grayscale chart so that the chart frame is aligned with the under scanned monitor frame. 5-22 HDC4300...

  • Page 123: Flare Adjustment

    If the lens aperture is greater than F5.6, adjust the light amount with the shutter. • Procedure Operate the control panel of MSU, and set as follows. (1) PAINT button → ON (lit) (2) Touch panel operation: (Page 1) → [Flare] 5-23 HDC4300...

  • Page 124: Gamma Correction Adjustment

    WHITE button → ON (lit) After the adjustment is completed, the message “AWB : OK” is displayed. Operate the control panel of MSU, and set as follows. (1) PAINT button → ON (lit) (2) Touch panel operation: (Page 1) → [Gamma] 5-24 HDC4300...

  • Page 125: Knee Point/Knee Slope Adjustment

    Touch panel operation: (Page 1) → [Knee] → [Knee Slope] Adjust the levels B to desired level for R, G and B respectively. • Adjustment item : [R], [G], [B], [Master] • Reference value : B = 735 mV 5-25 HDC4300...

  • Page 126: White Clip Level Adjustment

    Setting after Adjustment • Setting for MSU MASTER GAIN → 0 TEST 1 button → OFF (dark) 5-4-12. File Store After adjustments described in “5-4. Video System Level Adjustment” are completed, be sure to store the reference file. 5-26 HDC4300...
  • Page 127 Operate the control panel of MSU, and store file. (1) FILE button → ON (lit) (2) Touch panel operation: [Ref File] → [Ref Store] → [Store] After the reference file entry is completed, a message “Completed” is displayed. 5-27 HDC4300...

  • Page 128: Nd Offset Adjustment

    WHITE button → ON(lit) After the adjustment is completed, the message “AWB : OK” is displayed. Operate the control panel of MSU, and set as follows. • ND4 button → ON (lit) • MASTER GAIN → 6 dB 5-28 HDC4300...
  • Page 129 (1) FILE button → ON (lit) (2) Touch panel operation : [OHB File] → [OHB Store] → [Store] After recording is completed, a message “OHB File Stored” is displayed. Setting after adjustment • Setting for MSU MASTER GAIN → 0 5-29 HDC4300...

  • Page 130: Rpn Compensation

    • Manual RPN compensation adjustment data is not affected by executing the RPN automatic compensation(APR). • RPN automatic compensation(APR) may take several minutes. Execute RPN automatic compensation(APR) from MSU or execute AUTO CONCEAL of [RPN MANAGE] in the SERVICE menu. 5-30 HDC4300...

  • Page 131: Manual Rpn Compensation Adjustment

    Select(turn the knob) “YES” by rotary encoder and confirm(press the button).。 The message “COMPLETE” is displayed, the compensation data is recorded. If a compensation pixel has been wrongly recorded, delete the RPN data. ITEM: DELETE RPN → EXEC Repeat steps 4 to 6 to compensate other RPNs. 5-31 HDC4300...

  • Page 132: Procedures To Be Taken When The Rpn Compensation Fails

    Appearance of an RPN next to the pixel to be compensated means that adjacent RPNs exit. If an RPN appears in the diagonal direction, the RPN cannot be compensated. In this case, the CCD or the CCD block must be replaced. For more information, contact your local Sony Sales Office/Service Center. Procedure Open following page by camera setup menu.

  • Page 133: Performing Automatic Rpn Detection Effectively

    Open the following page by camera setup menu. MENU: SERVICE PAGE: RPN MANAGE <RPN MANAGE> S04 TOP RPN ALL PRESET : EXEC AUTO CONCEAL : EXEC APR AT ABB : ON Execute the automatic compensation of RPN. ITEM: AUTO CONCEAL → EXEC 5-33 HDC4300...

  • Page 135: Software Upgrade

    Copy the camera application update data to the USB drive using the following procedure. Note For how to obtain the version update data file (hdc4300_app.pkg), contact your local Sony Sales Office/Service Center. Create the following directory in the USB drive.
  • Page 136 Copy the OS update data to the USB drive using the following procedure. Note For how to obtain the version update data file (hdc4300_os.pkg), contact your local Sony Sales Office/Service Center. Create the following directory in the USB drive. \MSSONY\PRO\CAMERA\HDC4300 Copy the version update data file “hdc4300_os.pkg”...

  • Page 137: Pld

    This unit uses the PLD (Programmable Logic Device) that supports USB drive to write and rewrite the internal data. If the part listed below needs to be replaced or to be upgraded, contact your local Sony Sales Office/Service Center. Note The part number of PLD (or ROM for PLD) in which data is not written yet, is shown in “10.
  • Page 138 The unit restarts automatically and the version update starts. Upon completion of the version update, a message “UPDATE SUCCEEDED” appears. Turn off and on the unit and confirm that the version has been updated on the “ROM VERSION” page of the DIAGNOSIS menu. HDC4300...

  • Page 139: Forced Version Update

    Copy the software or PLD data version update data file to the USB drive using the following procedure. Note For how to obtain the version update data file, contact your local Sony Sales Office/Service Center. Create the following directory in the USB drive.

  • Page 141: File System

    This file is stored in the camera. OHB File (Refer to “7-7. OHB File”.) Used for adjustment of the CMOS block maintenance. This file can be stored in the camera. HDC4300...

  • Page 142: Structure Of Paint Related Files

    • ND offset Factory-set value 0 (*1): The additional data of each file is sent to each circuit in the unit. (*2): For items that can be stored in the scene file and the reference file, refer to “7-8. File Items”. HDC4300...

  • Page 143: Operator File

    [OPERATION] → [OPERATOR FILE] → [WRITE (CAM → USB)] Reading Reference: Refer to step 2 of “Outline Figure of Operation”. Using OPERATION Menu of This Unit Reads the operator file stored in the USB drive to the camera. [OPERATION] → [OPERATOR FILE] → [READ (USB → CAM)] HDC4300...

  • Page 144: Preset Operator File

    [FILE] → [OPERATOR FILE] → [STORE PRESET FILE] Initializing Reference: Refer to step 3 of “Outline Figure of Operation”. Using FILE Menu of This Unit Introduce preset operator file from the factory settings. [FILE] → [FILE CLEAR] → [PRESET OPERATOR] HDC4300...

  • Page 145: Scene File

    Select the scene file number to be called on the SCENE FILE page. [PAINT] →[SCENE FILE] → [1] ～ [5] A file currently being called is indicated with its file number highlighted. Select the number again to cancel the call and resume the previous status. HDC4300...
  • Page 146 Reads the scene file stored in the USB drive to the camera. [PAINT] → [SCENE FILE] → [READ (USB → CAM)] Note Scene File data stored in the USB drive cannot be read when the power is just turned on. HDC4300...

  • Page 147: Reference File

    Press the FILE button in the functional operation area on the operation panel. Select [Reference] → [Reference Store] by the menu operation. Reference file is stored in the camera and the numerical data is displayed as 0. (Excluding some items. Refer to “7-8. File Items”.) HDC4300...
  • Page 148 [FILE] → [REFERENCE] → [WRITE (CAM → USB)] Initializing All File Items Reference: Refer to step 5 of “Outline Figure of Operation”. Using FILE Menu of This Unit Re-set the reference file to the factory settings (default value: 0). [FILE] → [FILE CLEAR] → [REFERENCE (ALL)] HDC4300...

  • Page 149: Lens File

    [FILE] → [LENS FILE] → [STORE FILE] Set the lens extender to ON and repeat steps 4 to 7. For lens compatible with serial communication Check that the lens number is No. 17. Also check that the name of the lens and minimum f-stop value. HDC4300...
  • Page 150 [FILE] → [LENS FILE] → [STORE FILE] Set the lens extender to ON and repeat steps 5 to 7. Calling Using OPERATION Menu of This Unit Calls the lens file stored in the camera. [FILE] → [LENS FILE] → [No.] 7-10 HDC4300...

  • Page 151: Ohb File

    [FILE] → [OHB FILE] → [STORE FILE] With MSU (Master Setup Unit) Press the STANDARD button in the camera/panel control area on the operation panel (ON: lit). Press the FILE button in the menu operation area on the operation panel (ON: lit). 7-11 HDC4300...
  • Page 152 Perform the OHB matrix adjustment. [OHB] → [Adjusting] →[Matrix] Change the adjustment display by pressing the button 1, 2 of sub menu, and adjust the value of the OHB matrix. Store the OHB File. [OHB] → [OHB Store] → [Store] 7-12 HDC4300...

  • Page 153: File Items

    × × × ○ ing H Para-G Black Shad- × × × × ○ ing H Para-B Black Shad- × × × × ○ ing V Para-R Black Shad- × × × × ○ ing V Para-G Continued 7-13 HDC4300...
  • Page 154 × × Mod Shading × × ○ × × V Saw-R Mod Shading × × ○ × × V Saw-G Mod Shading × × ○ × × V Saw-B Master V Mod × × ○ × × Continued 7-14 HDC4300...
  • Page 155 Knee Aparture ○ ○ × × × Knee Apar- ○ ○ × × × ture HD Detail Detail Off ○ × × × Detail Level ○ ○ × × × Detail Limiter ○ × × × × Continued 7-15 HDC4300...
  • Page 156 ○ × × × Skin 3 Width ○ ○ × × × Skin 3 Sat ○ ○ × × × Skin 3 Y Lim- ○ ○ × × × Matrix Matrix Off ○ ○ × × × Continued 7-16 HDC4300...
  • Page 157 × × Low Key Sat- ○ ○ × × × uration level Gamma Gamma Off ○ × × × Gamma Cate- ○ ○ × × × gory Select STANDARD ○ ○ × × × Gamma Table Select Continued 7-17 HDC4300...
  • Page 158 × pression sion ON Level ○ ○ × × × Mono Color Mono Color On ○ Connected with CCU only Mono Color ○ ○ Connected Saturation with CCU only Mono Color ○ ○ Connected with CCU only Continued 7-18 HDC4300...
  • Page 159 SD Preset Ma- ○ ○ Connected trix On with CCU only SD User Matrix ○ ○ Connected with CCU only ○ ○ Connected with CCU only ○ ○ Connected with CCU only ○ ○ Connected with CCU only Continued 7-19 HDC4300...
  • Page 160 White Setup × × × × × Mode Digital ex- digital extender × × × × × tender Menu Item SCENE REFERENCE LENS OPERATOR Note File File File File File USER MENU — — — ○ — customize Continued 7-20 HDC4300...
  • Page 161 CENTER — — — ○ — SAFETY — — — ○ — ZONE EFFECT — — — ○ — ASPECT — — — ○ — MASK — — — ○ — SAFETY — — — ○ — Continued 7-21 HDC4300...
  • Page 162 — — ○ — BOX MEMOR — — — ○ — H POSI — — — ○ — V POSI — — — ○ — WIDTH — — — ○ — HEIGHT — — — ○ — Continued 7-22 HDC4300...
  • Page 163 — ○ — RET2 SW SEL — — — ○ — RET3 SW SEL — — — ○ — RET1 SW — — — ○ — +RET2 SW VBS RET AS- — — — ○ — PECT Continued 7-23 HDC4300...
  • Page 164 — — ○ — EARPHONE EARPHONE — — — ○ — RECEIVE SE- LECT INTERCOM — — — ○ — PGM1 — — — ○ — PGM2 — — — ○ — TRACKER — — — ○ — 7-24 HDC4300...

  • Page 165: Setup Menu

    • When AF DISPLAY is set to ON, the EFFECT display cannot be used. Instead of the EFFECT display, you can select 100% of the SAFETY ZONE display that usually cannot be selected. • If “Digital extender” is used, the area marker is not displayed correctly. HDC4300...
  • Page 166 “AF” is added to “VF DISPLAY” in the Operation menu. When this “AF” is set to ON, the focusing indicator appears. Focusing indicator: ▲ Front focus ■ Focal point ▼Rear focus HDC4300...

  • Page 167: Service Menu

    Gain extend, Chroma filter characteristic setting, Vol- page 8-8 ume over setting, Front microphone stereo setting, Mi- crophone AB power active setting CUSTOMIZE Page for Extensions page 8-9 8-2-2. Description of SERVICE Menu The display screen appearing in this section shows the factory settings. HDC4300...
  • Page 168 When using the RET2 switch after using RET1 switch, set the Insertion Mute time. If the Mute time is short, the noise may be appeared at the time of changing from RET1 to RET2. PsF DELAY MODE Set the delay time at the PsF format. HDC4300...
  • Page 169 Adjustment”. RPN MANAGE <RPN MANAGE> S04 TOP RPN ALL PRESET EXEC AUTO CONCEAL EXEC APR AT ABB The RPN MANAGE menu is used for RPN compensation setting and management. For details, refer to “5-6-4. Performing Automatic RPN Detection Effectively”. HDC4300...
  • Page 170 S07 TOP [R] [G] [B] V SAW V PARA : H SAW H PARA : WHITE STORE FILE: EXEC COLOR_TEMP_SEL: 3200K The WHITE SHADING menu is used for adjustment of the white shading. For details, refer to “5-3-2. Sensitivity Adjustment”. HDC4300...
  • Page 171 The setting is valid when S3 switch is set to RTS side on the SY-408 board. DISP INTERCOM1 ONLY When selecting INTERCOM2 switch on the rear panel to MIC ON, set indication/ non-indication of "TALK" in the viewfinder. ON : non-indication OFF : indication HDC4300...
  • Page 172 When switching the microphone ON/OFF by a belt pack etc., "TALK" in the viewfinder can be hidden. POWER SUPPLY STATUS2 This is the page for analysis about the consumption electricity. SERIAL NO. The display screen is the case of serial number 10001 of HDC4300. <SERIAL NO.> S11 TOP MODEL...
  • Page 173 Switch the IRIS knob on the control panel of the RCP-1000/1500 series so that the relative value mode turns to OFF and the absolute value mode turns to ON. FRONT MIC STEREO Change the front microphone to stereo. (The repair of hardware is necessary.) CUSTOMIZE For the function expansion in the future. HDC4300...

  • Page 175: Circuit Description

    This board equips 2/3 inch backside illumination type 4K CMOS image sensor (IC005). BI-291 boards are used for R, G and B respectively. 9-1-2. IF-1278 board This board equips power supply of CMOS image sensor and flash memory for saving the APR data. HDC4300...

  • Page 176: Signal Processing/Transmission System

    (ABB), shutter adjustment, Noise Reduction, aberration compensation and White/Gain adjustment are performed by R/ G/B signal input from CMOS block. The main line signal is sent to the MEM-147 board. Analog VF signal, embedded audio and lens control except picture process are performed. HDC4300...

  • Page 177: System Control System

    The main program is written in the flash memory (IC401) on the AT-189 board. 9-3-3. MB-1214 Board The MB-1214 board is the motherboard of this unit. This board contains interface connectors to be connected to other boards, inductors for power filters on each board, capacitors, and positive thermistors (overcurrent protection device). HDC4300...

  • Page 179: Spare Parts

    Therefore, specified parts should be used in the case 指定の部品を使ってください。 of replacement. 2. Standardization of Parts 2.  部品の共通化 Some repair parts supplied by Sony differ from those ソニーから供給する補修用部品は，セットに使われ used for the unit. These are because of parts common- ているものと異なることがあります。 ality and improvement.

  • Page 180: Exploded Views

    3-603-679-02 s STAINLESS SCREW +B3X10 3-612-669-01 o LID,POWER SW 3-672-250-01 s RING (M2.6), O 3-703-575-11 s PIN (DIA. 1.2X8), PARALLEL 3-742-066-11 o SPRING, SHUTTER 4-400-101-01 s POWER SW HOUSING 4-410-956-01 s SHEET, INSIDE(MULTI) 4-654-273-02 s ACE (M2), LOCK [B2x5] 10-2 HDC4300...
  • Page 181 A-1838-924-A s INSIDE PANEL SUBASSY 3-624-455-01 s TUBE,SHIELD 3-676-244-04 s COVER, SWITCH 4-294-962-01 s INSIDE PAD 4-415-077-01 s PANEL, BLANK(DC OUT) 4-415-079-01 s CAP, CONNECTOR(DC OUT) 4-575-378-01 s LABEL, FILTER 4-422-703-01 s TAPE, VHB 4-654-273-02 s ACE (M2), LOCK [B2x5] 10-3 HDC4300...
  • Page 182 2-640-315-02 o SCREW (M2X5), SMALL, +P, SW 3-257-200-01 s CLAMP, CORD 3-603-679-02 s STAINLESS SCREW +B3X10 3-672-250-01 s RING (M2.6), O 4-382-854-51 s SCREW (M3X6), P, SW (+) 4-546-928-01 s CUSHION (FAN) 4-654-273-02 s ACE (M2), LOCK [B2x5] 10-4 HDC4300...
  • Page 183 4-293-494-03 s CN BRACKET(CN-3434) 4-293-502-01 s CONNECTOR HOUSING 4-293-509-02 s ETHER CAP 4-424-320-03 s TRIAX DUCT (FAN) 4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 4-654-273-02 s ACE (M2), LOCK [B2x5] 3-079-115-01 s TAPE AS 7-682-548-09 s SCREW +B 3X8 10-5 HDC4300...
  • Page 184 3-079-115-01 s TAPE AS 3-624-455-01 s TUBE,SHIELD 3-676-244-04 s COVER, SWITCH 4-144-604-01 s SOFT SHIELD (3154) 4-293-514-01 s NUMBER FRAME 4-293-515-01 s NUMBER FRAME BASE 4-298-877-01 s SPRING, NUMBER FRAME 4-411-059-01 s LABEL(BNC) 4-654-273-02 s ACE (M2), LOCK [B2x5] 10-6 HDC4300...

  • Page 185: Front Panel

    A-1838-946-A s FRONT PANEL ASSY 2-623-773-11 s BOLT (M3X8), STAINLESS 3-603-679-02 s STAINLESS SCREW +B3X10 3-624-455-01 s TUBE,SHIELD 3-672-250-01 s RING (M2.6), O 3-870-272-02 s CLAMP, CABLE 4-138-679-01 s SCREW, BLIND 4-654-273-02 s ACE (M2), LOCK [B2x5] 7-623-208-22 s SW 3,TYPE 2 10-7 HDC4300...

  • Page 186: Ohb Block

    3-655-653-01 s BAND (TAITON), BINDING 3-699-048-01 s CAP, MOUNT 3-776-897-02 s GUIDE PLATE 4-263-184-04 s RING, BAYONET 4-562-323-01 s LEVER, MOUNT 4-654-273-02 s ACE (M2), LOCK [B2x5] 4-264-474-01 s BOLT,BHS M2X15 3-257-200-01 CLAMP, CORD 7-627-452-18 s SCREW,PRECISION +K 2X3 10-8 HDC4300...

  • Page 187: Incom Panel

    4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 2-640-315-02 o SCREW (M2X5), SMALL, +P, SW 4-654-273-02 s ACE (M2), LOCK [B2x5] 3-869-842-01 s CAP,SW 3-903-660-01 s DROP PROTECTION,TOGGLE 3-903-661-01 s ROD,GURAD 4-138-682-01 s SW COVER 4-414-613-03 s PANEL, INCOM (SY, J) 10-9 HDC4300...

  • Page 188: Mic Panel

    1-968-146-11 s HARNESS, SUB (EXT DC IN) 1-968-150-11 s HARNESS, SUB (UNREG) A-1860-043-A s MOUNTED CIRCUIT BOARD, CN-3432 1-968-153-11 s HARNESS, SUB (MIC) 1-784-240-11 s CONVERTER, COAXIAL CONNECTOR 1-968-154-11 s HARNESS, SUB (REMOTE) 1-830-742-11 s CABLE ASSEMBLY, COAXIAL 10-10 HDC4300...
  • Page 189 4-414-617-01 s CAP, REAR CONNECTOR 1 4-414-618-01 s CAP, REAR CONNECTOR 2 4-414-624-01 s PACKING, EARPHONE 4-414-625-01 s SHEET, SLIDE SW WATER RESIST 4-432-516-02 s SLIDING SHEET, SW 4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 4-654-273-02 s ACE (M2), LOCK [B2x5] 10-11 HDC4300...

  • Page 190: Ps Block

    PS Block Part No. SP Description Part No. SP Description A-1838-556-B s POWER BLOCK ASSY A-1860-029-A s MOUNTED CIRCUIT BOARD, SW-1528 A-1860-206-A s MOUNTED CIRCUIT BOARD, PS-836 10-12 HDC4300...
  • Page 191 4-415-078-01 s PACKING, DC OUT 4-415-274-01 s PS BRACKET 4-415-278-01 s STOPPER, PIN 4-415-279-01 s SUPPORT (3SQ-16), HEXAGON 4-415-280-01 s SHEET (T1), THERMAL 4-415-281-02 s SHEET(T1.5),THERMAL 4-415-282-01 s SHEET (T2), THERMAL 4-415-283-01 s SHEET (T3.5), THERMAL 4-415-284-02 s SHEET (T4), THERMAL 10-13 HDC4300...

  • Page 192: Dpr Block

    4-574-579-01 s SHEET (2.0 (38X38)), RADIATION 1011 4-533-878-01 s SHEET, RADIATION (L) 1012 4-382-854-51 s SCREW (M3X6), P, SW (+) 1013 4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 1014 1-543-793-11 s FILTER, CLAMP (FERRITE CORE) 1015 4-542-018-01 s GASKET (10X10X15) 10-14 HDC4300...

  • Page 193: Mb Block

    3-654-615-02 s COLLAR, SUSPENSION 1114 3-853-802-01 s CLAMP,REUSE 1115 3-870-137-02 s CAP, DROP PROTECTION 1116 4-293-489-01 s BRACKET CN-3426 1117 4-293-492-01 s GUARD, TAIL 1118 4-409-534-01 s SHEET, PS CASE THERMAL 1119 4-573-728-01 SHEET, COUNTERMEASURE 7-682-548-09 s SCREW +B 3X8 10-15 HDC4300...

  • Page 194: Front Sw Block

    1209 3-729-072-02 s SCREW, +K (4X8) 1210 3-742-066-01 s SPRING, SHUTTER 1211 3-742-067-06 s LID, SHUTTER 1212 3-872-587-01 s CUSHION,TOGGLE-SW 1213 3-872-601-01 s TOGGLE SW CUSHION(C) 1214 4-293-503-01 s FRONT SW COVER 1215 4-298-963-02 s FRONT SHIELD PLATE 10-16 HDC4300...

  • Page 195: Front Fan

    1-968-159-11 s HARNESS, SUB (LENS) 1307 1-968-162-11 s HARNESS, SUB (PS CONT, FRONT) 1308 2-640-315-02 o SCREW (M2X5), SMALL, +P, SW 1309 3-629-684-02 s FORM,SHIELD 1310 3-796-945-01 s CUSHION,FAN 1311 4-293-504-01 s FRAME, SUB 1312 4-411-696-01 s SLIDING SHEET, OHB 10-17 HDC4300...

  • Page 196: Hotshoe Block

    3-872-522-02 s SPRING,COMPRESSION(STOPPER) 7-682-548-09 s SCREW +B 3X8 1406 3-872-550-02 s STOPPER(R),HOT DOOR 1407 3-872-551-02 s STOPPER(L),HOT DOOR 1408 3-872-573-02 s WATER PROTECT(HOT DOOR) 1409 4-382-854-51 s SCREW (M3X6), P, SW (+) 1410 4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 10-18 HDC4300...
  • Page 197 4-654-273-02 s ACE (M2), LOCK [B2x5] 1507 2-640-315-02 o SCREW (M2X5), SMALL, +P, SW 1508 3-654-615-02 s COLLAR, SUSPENSION 1509 3-676-244-04 s COVER, SWITCH 1510 3-701-507-01 s SET SCREW, DOUBLE POINT,(M3X5) 1511 3-872-534-02 s WASHER02 1512 3-872-537-01 s PIN,HANDLE LOCK 10-19 HDC4300...
  • Page 198 3-711-765-01 s BOLT (M3), HEXAGON SOCKET 1612 3-711-794-12 s PIN, STOPPER 1613 3-872-615-02 s PLATE,VF SLIDE 1614 3-895-622-01 s RING (DIA. 5), O 1615 4-137-907-02 s PIPE,VF SLIDE(LONG) 1616 4-293-491-01 s COVER, TOP(2) 1617 4-549-633-01 s KNOB, LOCK 1618 4-558-057-01 s SHOE,SLIDE 10-20 HDC4300...
  • Page 199 2-640-315-02 o SCREW (M2X5), SMALL, +P, SW 1707 3-872-543-01 s SPRING,COMPRESSION(HANDLELOCK) 1708 4-138-679-01 s SCREW, BLIND 1709 4-293-486-02 s COVER, TOP 1710 4-299-188-01 s BUTTON, HANDLE RELEASE 1711 4-408-829-01 s SHEET, TOP 1712 4-559-446-01 s SCREW, +P2.6X5 LOCK ACE 10-21 HDC4300...

  • Page 200: Supplied Accessories

    10-3. Supplied Accessories Supplied Accessories Q'ty Part No. SP Description 4-138-677-01 s BRACKET, BELT 4-138-758-01 s CLAMP BELT, CABLE 4-408-856-01 s LABEL, NUMBER 2pcs 7-682-548-09 s SCREW +B 3X8 10-22 HDC4300...

  • Page 201: Block Diagrams

    CN105:28 IIC_SDA/SCK_OHB 74CLK-out CN300(3/3):1,2 163,165 CN105(2/3):35,37 CN101:30 27CLK-out IC1806 CN105(2/3):171 74CLK-out IC1812 CN105(2/3):172 IC1806 27CLK-PROTEIN 27CLK-ROSE&PREMA CN107 27M-PLL-VAR, X1801 IC1802,1804,1816 IC1800 IC1817,1818 MB-1214(3/4) 27CLK-ADV 27K-PLL-REF CN9:2 IC1700 DRIVER COMPARATOR SDI-27M-CLK CN105:35 27MHz CN106 27CLK-out DC FAN CN101:29 (REAR) 11-1 HDC4300...
  • Page 202 NET-WORK-INT-IN, BUFFER D-FF NET-WORK-CS-IN 23,25,26 IC007 IC509,510 IC502 IC504 VCO501,502 IC506 SD-27CK-in SD-27CK-IN IC205 COMPARATOR DRIVER MAIN-74CK_MEM VCO501:148.352MHz IC503 VCO502:148.5MHz HD-74CK-IN MAIN-74CK_SDI IC002 IC015 CN007 TEMP_SENS_IIC_SDA/SCL REAR_FAN_CONT[0]-[6] FAN(+) TEMP REAR_FAN_OFF DC FAN IC202,203 (OUTSIDE) SDRAM REAR_FAN_PULSE IC402 FLASH 11-2 HDC4300...
  • Page 203 CALL SY-CALL-SW 16 BIT RTC_SDA, DC IN 1,2,5,6 1,2,5,6 AB33_A[1]-[16] eMMC 11-14 +5.5V D-TYPE IC306 RTC_SCL AB33_A[1]-[16], (4GB) AB33_ADV 115,117 LATCH 19,21,22 +3.7V AB33_AD[0]-[15] CN51 -5.5V OPT-VR1 IC804 IC402,403 OPT-VR2/3 OPTION 12,13, IC805 DDR2 UART0_TX/RX (128MB) 1-7,15 83,85 11-3 HDC4300...

  • Page 204: Frame Wiring

    J401 COAXIAL CABLE (BI-IF) SDI1 J402 COAXIAL CABLE SDI2 J901 DEBUG HARNESS (BI-IF) TX-146 OPTICAL MULTI CABLE ASSEMBLY :HDC4300/T HARNESS OPTICAL MULTI CABLE ASSEMBLY-M:HDC4300/L (BI-IF) CN004 CN005 CN001 CN002 CN901 CN902 CN1301 CN501 CN004 CN001 CN-3434 DEBUG FINE-WIRE COAXIAL CABLE...
  • Page 206 HDC4300 (SY) HDC4300 (CED) HDC4300 (CN) Printed in Japan Sony Corporation HDC4300 (J) J, E 2015. 4 08 9-878-636-01 © 2015...

Table of Contents

Save PDF