Table of Contents
Advertisement
Available languages
Available languages
For Direct Wire
Cabinet Grommet
For 1 1/2" (38 mm) hole in
cabinet
NOTE: Required for metal
cabinets
NOTE: Be sure to purchase only Whirlpool factory-certified parts
and accessories for your appliance. Your installation may require
additional parts. To order, refer to the contact information
referenced in your Quick Start Guide.
Location Requirements
Dishwasher must be fully enclosed (top, sides, back, and floor)
upon installation. A side panel kit is available from your dealer for
installing your dishwasher at the end of your cabinetry.
An optional moisture barrier accessory is also available for
installing underneath a wooden countertop.
Check location where dishwasher will be installed. The location
must provide:
� Convenient access for loading and unloading dishes. Corner
locations require a 2" (51 mm) minimum clearance between
the side of the dishwasher door and the wall or cabinet.
� Easy access to water, electricity, and drain:
• Grounded electrical supply is required.
• This dishwasher has a water-heating feature and also
requires a connection to a hot water supply line.
• Make sure pipes, wires, and drain hose are within the
shaded area shown in the "Cabinet Opening Dimensions"
section.
• Do not run drain lines, water lines, or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
• Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
NOTE: If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
• If installed in new construction, flush the water supply line of
debris before connecting it to the fill valve. If it is not
flushed, debris from the water supply could plug the fill
valve screen.
� A square opening for proper operation and appearance.
� The cabinet front to be perpendicular to floor.
� A level floor.
For Power Cord
Power Cord Kit
Kit typically includes power
cord, metallic strain relief,
grommet, and twist-on wire
connectors (Straight: Whirlpool
Part Number 4317824, 90°:
Whirlpool Part Number
W10278923RP). For proper
installation, refer to the
installation instructions
provided with the kit.
Helpful Hint: If floor at front of opening is not level with floor at
rear of opening, shims may be used to level dishwasher.
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
� The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should
not touch the floor.
� Do not install dishwasher over carpeted flooring.
Cabinet Opening Dimensions
Clearances
Check that all surfaces have no protrusions that would prohibit
dishwasher installation.
C. Measured from the lowest point on the underside of the
countertop. May be reduced to 33 1/2" (851 mm) by removing
the wheels and perforated area of insulation (blanket) on
dishwasher.
D. Minimum, measured from narrowest point of opening.
NOTE: Shaded areas of cabinet walls show where utility
connections may be installed.
Drain Requirements
� A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft. (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher.
NOTE: Do not connect multiple drain hoses together.
� Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
7
Hide quick links:
Advertisement
Table of Contents
