Related Manuals for Silvercrest SEKU 2000 A16
Summary of Contents for Silvercrest SEKU 2000 A16
- Page 1 Electric Fireplace SEKU 2000 A1 Electric Fireplace Operating instructions KOMPERNASS GMBH BURGSTRASSE 21 · D-44867 BOCHUM www.kompernass.com ID-Nr.: SEKU 2000 A1-05/10-V3...
-
Page 2: Table Of Contents
Contents Introduction ..... . 2 Information for these operating instructions ..2 Copyright ....... 2 Limited liability . -
Page 3: Introduction
Introduction Information for these operating instructions These operating instructions are a component of the SEKU 2000 A1 Electric Fireplace (henceforth designated as the appliance) and they provide you with important information about the intended use, safety, installation and connection as well as operation of the appliance. These operating instructions must at all times be kept available close to the appliance. -
Page 4: Warnings
Introduction Warnings In these operating instructions the following warnings are used: DANGER A warning at this danger level indicates a threateningly dangerous situation. If the dangerous situation is not avoided, it could result in death or serious injury. Compliance with the instructions in this warning is necessary to avoid the risk of death or serious injury. ►... -
Page 5: Safety
Safety In this chapter you are being given important safety information regarding the handling of the appliance. This appliance complies with the statutory safety regulations. Incorrect usage can, however, lead to personal and property damage. Risk of electrocution DANGER Risk of electrocution! A potentially fatal situation can arise from contact with live wires or components! Pay heed to the following precautions to avoid the risk of electric shock: Do not use the appliance if the mains power plug or the connecting cable are damaged. -
Page 6: Setting Up And Connecting
Setting up and connecting Defective components may only be replaced with original replacement parts. Only by using original ■ replacement parts can it be guaranteed that the safety requirements are being complied with. Protect the appliance from moisture and liquid penetration. ■... -
Page 7: Installation Requirements
Installation requirements For the safe and correct operation of the appliance, the installation site must satisfy the following requirements: The appliance must be placed on a fi rm, fl at and horizontal surface. ■ Do not place the appliance in a hot, wet or very humid environment or close to infl ammable materials. ■... -
Page 8: Operating Components
Operating components Operating components NOTICE The operating elements are on the front of the appliance, above right and behind the ventilation grille. ► To operate them, fold the ventilation grille forward. ► ON/OFF switch (Flames) ON/OFF switch (Heating, level 1) ON/OFF switch (Heating, level 2) Temperature control (Thermostat) Dimmer (for fl... -
Page 9: Set Up
Set up Before the appliance can be set up, the fi re surround must be assembled. NOTICE Check the contents to make sure everything is there and for visible damage. ► Firstly, become familiar with all parts involved in the assembly. ►... -
Page 10: Screws And Assembly Material
Set up Screws and assembly material No.: Designation: Screws 6 x 25 mm Wood plugs Double locking pin Single locking pin Adapter sleeve Fixing device NOTICE You require a screwdriver for the assembly; this is not supplied. ► The assembly of the fi re surround is described in detail in the following. NOTICE Carry out the assembly step by step in the order as described. -
Page 11: Assembly
Assembly Step 1 Screw three single locking pins Place two wood plugs Insert three adapter sleeves screwdriver line up the adaptor sleeves edge of the side panel Then, bring the front panel enter the holes on the left edge of the side panel When done, screw all three adapter sleeves clamped into the adapter sleeves and the panels are seated fi... - Page 12 Assembly Then, bring the front panel enter the holes on the right edge of the side panel. When done, screw all three adapter sleeves clamped into the adapter sleeves and the panels are seated fi rmly together and at right angles. Step 3 Take the centre front panel Then place four adapter sleeves...
- Page 13 Step 5 Place the fl oor plate Now take the previously assembled unit and carefully place it on the fl oor plate as shown in the following diagramme. Then screw together the assembled unit with the connection blocks 8 screws of the type Step 6 Take the top covering panel Secure the top covering panel...
- Page 14 Assembly Step 7 Take the base plate Then place the base plate the fl oor plate. Rear view Installing the appliance in the fi re surround To fi nalise, install the appliance in the assembled fi re surround. Place the appliance carefully on the base plate (from the rear of the fi re surround) and then push it gently forward as far as it will go into the opening of the fi...
-
Page 15: Handling And Operation
Handling and operation NOTICE See also "Operating Elements" on page 7. ► In this chapter you receive important information for the handling and operation of the appliance. Activate the ON/OFF switch desired brightness with the Dimmer Then, turn the heater on with the switch 1 (1000 W). -
Page 16: Cleaning
Maintenance/Cleaning/Troubleshooting Switch the appliance off . Pull the plug from the mains power socket. Loosen the four screws on the rear panel and remove the metal ventilation panel Carefully replace the defective bulb Screw the metal ventilation panel Cleaning WARNING Observe the following safety information to avoid risks and property damage: Clean the appliance ONLY when it is switched off... -
Page 17: Malfunction Causes And Remedies
Malfunction causes and remedies The following table will help with localising and remedying minor malfunctions: Defect The fl ame replication does not light up. The appliance does not heat. The fan does not run. The heating is not switched off . NOTICE If you cannot solve the problem with the aforementioned methods, please contact Customer Services. -
Page 18: Appendix
Appendix Appendix Technical data General Input voltage Mains frequency Power consumption Heating level 1 Heating level 2 Bulb 2 x Bulbs E14 Ambient temperature Humidity (no condensation) Measurements (W x H x D): Weight Notes on the EC Declaration of Conformity This appliance complies with, in regard to conformance to the basic requirements and other relevent regulations, the European Directive Low Voltage Directive 2006/95/EC as well as the European Directive for Electromagnetic Compatibility 2004/108/EC. -
Page 19: Warranty
Warranty You receive a 3-year warranty for this appliance as of the purchase date. The appliance has been manu- factured with care and meticulously examined before delivery. Please retain your receipt as proof of purchase. In the case of a warranty claim, please make contact by telephone with our Service Department.