CARBON PAINTED ON THE CRT, AFTER REMOVING THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE ANODE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 –...
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 TABLE OF CONTENTS Section Title Page Section Title Page SELF DIAGNOSIS FUNCTION 5. DIAGRAMS ........ 4 5-1. Block Diagram ............49 1. GENERAL ................ 8 5-2. Frame Schematic Diagram ........52 Circuit Boards Location .......... 55 2. DISASSEMBLY 5-4.
Page 4
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 SELF DIAGNOSTIC FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 5
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT 2 times 5 times Lamp ON 0.3 sec. Lamp OFF 3 sec. Lamp OFF 0.3 sec. STANDBY/SLEEP lamp Diagnostic Item Flash Count* +B overcurrent/overvoltage 2 times Vertical deflection stopped White balance failure 5 times * One flash count is not used for self-diagnostic.
Page 6
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [Screen display] / channel [5] / Sound volume [-] / Power ON...
Page 7
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 SELF-DIAGNOSTIC CIRCUIT IC301 IC001 IC003 Y/CHROMA JUNGLE SYSTEM MEMORY FROM IK-IN IO-8DAT B-DAT FROM [+B] Q604 C O-LED PROTECT IO-SDAT [H] D526 [V] Q509/507 [+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven verticals in a period, the unit will automatically turn off.
KV-XF29M50/XF29M63/XF29M80 SECTION 3 KV-XF29M83/XF29M90 RM-954 SET-UP ADJUSTMENTS • The following adjustments should be made when a complete Perform the adjustments in the following order : realignment is required or a new picture tube is installed. 1. Beam Landing • These adjustments should be performed with rated power 2.
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 3-2. CONVERGENCE Preparation : • Before starting this adjustment, adjust the focus, horizontal size V. STAT and vertical size. • Minimize the brightness setting. • Provide dot pattern. (1) Horizontal and Vertical Static Convergence Center dot H. STAT VR V.
Page 37
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 Y separation axis correction magnet adjustment. Blue Neck assy Neck assy 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [STANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of Blue the screen are straight.
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 Rotate TLV-2 VOL (29”, 34”) on DY 3-3. FOCUS ADJUSTMENT Rotate TLV VOL (25”) on DY Adjust FOCUS control on the flyback transformer for the best XCV Rotate XCV Adj core on DY focus. YCH Rotate YCH VOL on DY Insert Correction Plate to DY Pocket (Left or Right)
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 2. WHITE BALANCE ADJUSTMENT 3-4. G2 (SCREEN) AND WHITE BALANCE 1) Set to Service Mode (Refer Section 5-1: ADJUSTMENTS ADJUSTMENTS WITH COMMANDER). 1. G2 (SCREEN) ADJUSTMENT 2) Input white raster signal. 1) Set the PICTURE and BRIGHTNESS to normal. 3) Set the PICTURE to minimum.
KV-XF29M50/XF29M63/XF29M80 SECTION 4 KV-XF29M83/XF29M90 RM-954 CIRCUIT ADJUSTMENTS 4-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-954 that comes with 1, 4 this unit. Select the adjustment item. ↓ a. ENTERING SERVICE MODE 3, 6 Raise/lower the data value. With the unit on standby ↓...
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 4-2. ADJUSTMENT METHOD Item Number 00 of device GEO Use the same method for all Items. Use 1 and 4 to select the This explanation uses H-Position as an example. 1. Select “GEO 00 HPS” with the 1 and 4 buttons. adjustment item, use 3 and 6 to adjust, write with [MUTING] 2.
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 RM-954 4-3. PICTURE QUALITY ADJUSTMENTS BELL FILTER ADJUSTMENT SUB COLOR ADJUSTMENT 1. Input SECAM color-bar signal. 2. Connect the dual-trace oscilloscope to CN303 pin 9 1. Input a PAL color-bar. (not mounted). 2. Set to the following condition: 3.
Page 53
KV-XF29M50/XF29M63/XF29M80 SECTION 7 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. ELECTRICAL PARTS LIST Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK NOTE: • Items marked " ∗ " are not stocked since they •...
Page 54
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C524 1-126-967-11 ELECT 47MF C611 1-161-830-00 CERAMIC 0.0047MF 500V C526...
Page 55
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK CN201 * 1-564-510-11 PLUG, CONNECTOR 7P D517 8-719-945-80 DIODE ERC06-15S CN202 * 1-508-847-00...
Page 56
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK FB603 1-410-397-21 FERRITE 1.1UH L101 1-414-856-11 INDUCTOR 10UH FB604 1-410-397-21...
Page 57
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK Q502 8-729-216-22 TRANSISTOR 2SA1162-G R035 1-216-025-91 RES,CHIP 1/10W Q503 8-729-230-49...
Page 58
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R326 1-216-029-00 RES,CHIP 1/10W R527 1-216-001-00 RES,CHIP 1/10W R327 1-216-033-00...
Page 59
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R598 1-249-438-11 CARBON 1/4W R909 1-216-065-91 RES,CHIP 4.7K 1/10W R599...
Page 60
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M50/XF29M80 KV-XF29M90 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <MODULE> C3209 1-163-017-00 CERAMIC CHIP 0.0047MF C3210 1-126-964-11...
Page 61
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M50/XF29M80 KV-XF29M90 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C3281 1-163-037-11 CERAMIC CHIP 0.022MF D1411 8-719-158-35 DIODE RD9.1SB...
Page 62
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M50/XF29M80 KV-XF29M90 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK Q3201 8-729-224-61 TRANSISTOR 2SK246-Y R1471 1-216-022-00 RES,CHIP 1/10W...
Page 63
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M50/XF29M80 KV-XF29M63 KV-XF29M90 KV-XF29M83 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R3237 1-216-075-00 RES,CHIP 1/10W R3297 1-216-069-00...
Page 64
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M63 KV-XF29M83 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C1445 1-163-133-00 CERAMIC CHIP 470PF C3282 1-126-964-11 ELECT...
Page 65
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M63 KV-XF29M83 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <CONNECTOR> <CHIP CONDUCTOR> CN1400* 1-564-512-11 PLUG, CONNECTOR 9P JR1405 1-216-295-91...
Page 66
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M63 KV-XF29M83 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R1409 1-216-105-91 RES,CHIP 220K 1/10W R1498 1-216-025-91 RES,CHIP...
Page 67
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. KV-XF29M63 KV-XF29M83 REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R3285 1-216-073-00 RES,CHIP 1/10W * A-1331-872-A C BOARD, COMPLETE R3286 1-216-073-00 RES,CHIP...
Page 68
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK D720 8-719-911-19 DIODE 1SS119-25 R1801 1-249-426-11 CARBON 5.6K 1/4W D721...
Page 69
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C2833 1-137-366-11 FILM 0.0022MF R2806 1-216-073-00 RES,CHIP 1/10W C2834 1-106-375-12...
Page 70
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * A-1241-346-A F BOARD, COMPLETE <CAPACITOR> (KV-XF29M50(GE)/XF29M80/XF29M83) ******************** C3900 1-136-153-00...
Page 71
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <TRANSISTOR> <DIODE> Q3901 8-729-030-02 TRANSISTOR DTC144ESA D3453 8-719-110-72 DIODE RD30ESB2 Q3902...
Page 72
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <COIL> R5931 1-249-413-11 CARBON 1/4W R5932 1-249-413-11 CARBON 1/4W L5901...
Page 73
KV-XF29M50/XF29M63/XF29M80 KV-XF29M83/XF29M90 The components identified by shading RM-954 and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK * 4-066-926-01 CUSHION (UPPER) (ASSY) * 4-066-927-01 CUSHION (LOWER) (ASSY) 4-392-003-11 BAND, HOLD...
KV-XF25M50/XF25M80 KV-XF25M50/XF25M80 KV-XF25M50/XF25M80 KV-XF25M50/XF25M80 RM-954 RM-954 RM-954 RM-954 SECTION 5 DIAGRAM 5-1. BLOCK DIAGRAM TRU Surround AUDIO PROCESSOR L1 out TV V in AV SW DBFB (3D) AUDIO OUT IC3201 IC3206 IC3207 TDA7315D R1 out MAIN. TUVIF TV L in IC1401 with NJM2187L...
(1) Schematic Diagram of A Board (1/2) CN204 CN203 CN102 TO B3 BOARD CN1405 TO H3 BOARD CN201 :BTOB TO B3 BOARD CN3603 CN608 CN1407 CN303 CN106 CN101 :S-MICRO CN105 CN104 :S-MICRO TO B3 BOARD CN205 CN302 TO B3 BOARD TO B3 BOARD :MINI CN1406...
Page 79
(2) Schematic Diagram of A (2/2) Board CN507 R501 :S-MICRO NS ROT :CHIP TO C BOARD NS MUTE R500 CN1801 135V 135V R596 135V 135V 135V 135V 135V 135V POWER SUPPLY,HV,MICON 135V L516 R502 L517 C500 R544 L515 3W :RS :DCC NS ROT C514...
Page 80
(3) Schematic Diagram of B Board A BOARD N OT E : The circuit indicated at left contains high voltage of over D004 [COMB FILTER] [POWER SUPPLY, HV, MICON, Y/C JUNGLE] D615 D005 600 Vp-p. Please pay attention when inspecting or repair- D616 IC001 B-10...
Page 81
(4) Schematic Diagrams of H and VM Boards TO B3 BOARD TO B3 BOARD TO A BOARD TO SP TO J2 BOARD TO B3 BOARD TO A BOARD TO F BOARD TO A BOARD CN6204 CN6202 CN904 CN3451 CN1400 CN104 CN4602 CN5901 CN601...
Page 82
(5) Schematic Diagram of B Board CN1400 TU1401 :S-MICRO C1461 R1411 C1460 D1415 470p :CHIP AUDIO(R) CH:CHIP F:CHIP UDZSTE-179.1B R/L/Y/S/C/CV R3272 6.8k R IN :CHIP R1420 C1450 C1453 R1412 R1409 C1462 JR1409 R1474 220k F:CHIP :CHIP JW1481 C1437 C1463 :CHIP R3211 L IN AUDIO(L)
KV-XF25M50/XF25M80 KV-XF25M50/XF25M80 RM-954 RM-954 BOARD IC3201 NJM2187L PRINTED WIRING BOARD Lch out Lch in [AUDIO PROSESSOR, AV SWITCH] BYPASS FIL 1 3D–STEREO Rch in Rch out SPACE VR 3D–STEREO BYPASS CENTER VR FIL 2 – B Board – Schematic diagram board –...
Page 84
(6) Schematic Diagram of F Board C BOARD IC701 STV5112 BLUE FEEDBACK (RED FEEDBACK, GREEN FEEDBACK) (CISPR) BLUE OUTPUT CN4601 T4602 F4601 (RED OUTPUT, VDR461 JW4603 250V GREEN OUTPUT) T4601 :FUSE AC IN AC OUT JW4604 R4601 AC IN AC OUT 1/2W BLUE CATHODE CN4602...